Question about 2006 GMC Sierra

1 Answer

How to remover motor from radiator fan - 2006 GMC Sierra

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • GMC Expert
  • 211 Answers

Posted on Dec 31, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Need to replace radiator fan and its motor


need to remove the fan unscrew the fan center nut and remove fan blade from motor.to remove fan motor from shroud remove the three mounting screws in back of fan motor.

Jan 25, 2013 | 1997 Honda Civic

1 Answer

Cooling fan burned up


Get a new fan motor and blade from GM or from an aftermarket supplier.

GM parts are usually better than the aftermarket ones, though for fit and functioin.

May also look into checking the relays and harness. If the terminals of the fan show they are getting current, then the motor will have to be replaced if not turning or obviously burnt.

Good luck on this repair.
---

Inspect/Replace

CAUTION
The fan that draws cool air across the radiator can be driven by either a belt or electricity. Rotating fans can be dangerous. Some are controlled by an automatic switch and can start unexpectedly. When working on electric fans, keep in mind that electric cooling fans should be disconnected when working around them.
When replacing a radiator fan motor, always refer to the vehicle's service manual. The following is a general guide for cooling fan replacement.

  • Disconnect the negative battery terminal at the battery. This is necessary on vehicles using electric fans, but some vehicles may require the relocation of the charging system components.
  • Drain the cooling system.
  • Loosen or remove the hose clamps, then remove the upper and lower hoses from the radiator.
  • Disconnect the transmission cooling lines and plug them off, if equipped.
  • Disconnect the electric fan motor connector, if equipped.
  • Remove the fasteners attaching the fan module to the radiator.
  • On some vehicles equipped with air conditioning systems, it may be necessary to discharge the system. This is the case if the radiator and condenser can not be separated in the vehicle.
  • Remove the upper radiator cross member or mounts.
  • Disconnect and plug the air conditioning lines at the condenser, if needed.
  • Remove the radiator and fan module as one unit if possible.
  • Separate the fan module from the radiator.
  • If required, separate the radiator from the condenser.
  • Remove the old fan module.
  • Install the new fan module onto the radiator.
  • Reattach the fasteners attaching the fan module to the radiator.
  • If equipped, connect the electric fan motor connector.
  • Reinstall the radiator.
  • Refill the cooling system.

Oct 29, 2010 | 1997 Chevrolet Cavalier

1 Answer

How to replace a radiator fan motor on a Chevrolet Cavalier


You will have to remove the cooling fan motor assembly by removing the lower mount bolt and lifting the scroud off of a lip on the top of the radiator. Remove the fan and remove the motor.

Sep 12, 2010 | 1999 Chevrolet Cavalier

1 Answer

How to change a radiator


1988–91 Models
  1. Disconnect the negative battery cable.
  2. Properly drain the cooling system into a suitable container.
  3. Disconnect the fan motor and motor connector.
  4. Disconnect the upper and lower radiator hoses.
  5. Disconnect and plug the automatic transaxle cooling lines at the radiator, if equipped.
  6. Disconnect the coolant reservoir overflow hose.
  7. Remove the radiator attaching bolts and brackets.
  8. Remove the radiator with the cooling fan attached.
  9. Remove the cooling fan and shroud from the radiator. NOTE: Check all cooling system hoses for any signs of damage, leaks or deterioration and replace if necessary. To install:
  10. Attach the cooling fan and shroud to the radiator and install the assembly.
  11. Attach the radiator bolts and brackets. Tighten the radiator bracket bolts to 7 ft. lbs. (10 Nm).
  12. Connect the coolant reservoir overflow hose.
  13. Connect the automatic transaxle cooling lines to the radiator, if equipped.
  14. Connect the upper and lower radiator hoses.
  15. Connect the fan motor and thermo-switch wire connector.
  16. Refill the system with the proper type and quantity of coolant, check for leaks and bleed the cooling system.
  17. Reconnect the negative battery cable. Fig. 7: Cooling system components — 1988–91 engines 86833085.gif
1992–95 Models
  1. Disconnect the negative battery cable.
  2. Properly drain the cooling system into a suitable container.
  3. Disconnect the fan motor and motor connector.
  4. Disconnect the upper and lower radiator hoses.
  5. Disconnect and plug the automatic transaxle cooling lines at the radiator, if equipped.
  6. Disconnect the coolant reservoir overflow hose.
  7. Remove the radiator attaching bolts and brackets.
  8. Remove the radiator with the cooling fan attached.
  9. Remove the cooling fan and shroud from the radiator. NOTE: Check all cooling system hoses for any signs of damage, leaks or deterioration and replace if necessary. To install:
  10. Attach the cooling fan and shroud to the radiator and install the assembly.
  11. Attach the radiator bolts and brackets. Tighten the radiator bracket bolts to 7 ft. lbs. (10 Nm).
  12. Connect the coolant reservoir overflow hose.
  13. Connect the automatic transaxle cooling lines to the radiator, if equipped.
  14. Connect the upper and lower radiator hoses.
  15. Connect the fan motor and thermo-switch wire connector.
  16. Refill the system with the proper type and quantity of coolant, check for leaks and bleed the cooling system.
  17. Reconnect the negative battery cable. Fig. 8: Cooling system components — 1992–95 engines 86833086.gif
prev.gif next.gif

Aug 27, 2010 | 1991 Honda Civic

1 Answer

Need instructions on how to replace the cooling


Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Radiator upper crossmember
    • Fan motor electrical connector
  3. Drain cooling system below the level of the upper radiator hose.
  4. Remove or disconnect the following:
    • Upper radiator hose from radiator
    • Radiator fan fasteners and upper clip
    • Fan assembly by lifting upward to clear radiator
To Install:
  1. Install or connect the following:
    • Radiator fan assembly
    • Upper clip and fasteners
    • Upper radiator hose to radiator
    • Fan motor electrical connector
    • Radiator upper crossmember
  2. Fill cooling system.
prev.gif next.gif

Jul 17, 2010 | 2004 Dodge Intrepid

1 Answer

How do I remove the cooling fan shroud from the top of the radiator ? I'm trying to change the cooling fan motor, and I've removed the bolt holding the fan shroud to the radiator, but I can't get the...


I would suggest replacing the cooling fan relay in the fuse compartment under the hood first. Cooling fan motors very, very rarely go bad. You will probably end up having to remove the radiator to remove the shroud. You will save yourself a lot of time and money if you replace the relay first.

Jul 07, 2010 | 1996 Chevrolet Cavalier

1 Answer

How do you change a cooling fan motor? I can't get it off the fan shroud.


You must drain the coolant from the radiator by unscrewing the drain on the drivers side of the radiator, remove the radiator hold downs (10mm) and pull up the radiator carefully to remove the 4 10mm bolts that hold the fan to the radiator, the fan unplugs right at the motor.

May 17, 2010 | 1994 Ford Escort

1 Answer

How do you replace a radiator in a dodge shadow 1993


These are the instructions for a 4 cylinder motor.

  1. Disconnect the negative (-) battery cable.

CAUTION Do NOT remove the cylinder block or the radiator draincock with the system hot and under pressure because serious burns from coolant can occur.
  1. Drain the cooling system.
  2. Remove the hose clamps and hoses from the radiator. Remove the coolant reserve system tank-to-filler neck tube.
  3. Remove the automatic transaxle hoses, if so equipped.
  4. Remove the fan and fan support assembly by disconnecting the fan motor electrical wiring.
  5. Remove the fan shroud retaining clips, located on the top and bottom of the shroud for most of the vehicles (the Dynasty has them only on the top).
  6. Lift the shroud up and out of the bottom shroud attachment clips separating the shroud from the radiator. Avoid damaging the fan.
  7. Remove the upper radiator mounting screws. Disconnect the engine block heater wire, if so equipped.
  8. Remove the air conditioning condenser attaching screws located at the top front of the radiator, if the vehicle is equipped with air conditioning.
  9. Lift the radiator free of the engine compartment.
Care should be taken to NOT damage the radiator cooling fins or water tubes during removal or installation.
To install:
  1. Slide the radiator down into position behind the radiator support.
  2. Attach the air conditioning condenser to the radiator, if so equipped, with a force of approximately 10 lbs. (44 N) to seat the radiator assembly lower rubber isolators in the mount holes provided.
  3. Tighten the radiator mounting screws to 108 inch lbs. (12 Nm).
  4. Connect the automatic transaxle hoses, if so equipped. Tighten the hose clamps to 35 inch lbs. (4 Nm).
  5. Slide the fan shroud, fan and motor down into the clips on the lower radiator flange. Install new shroud retaining clips.
  6. Install the upper and lower radiator hoses (including the coolant reserve hose).
  7. Plug the fan motor electrical connection and attach the negative (-) battery cable.
  8. Fill the cooling system with coolant (refer to Section 1 for more details).
  9. Operate the engine until it reaches normal operating temperature. Check the cooling system and automatic transaxle (if equipped) for the correct fluid levels. Also check for coolant leaks.
Here are the instruction for a 6 cylinder engine.
6-Cylinder Engines
  1. Disconnect the negative (-) battery cable.

CAUTION Do NOT remove the cylinder block or the radiator draincock with the system hot and under pressure because serious burns from coolant can occur.
  1. Drain the cooling system.
  2. Remove the hose clamps and hoses from the radiator. Remove the coolant reserve system tank to filler neck tube.



  1. Remove the automatic transaxle hoses, if so equipped.
  2. Remove the fan and fan support assembly by disconnecting the fan motor electrical wiring.
  3. Remove the fan shroud retaining clips, located on the top and bottom of the shroud for most of the vehicles (the New Yorker, Dynasty, Fifth Ave., and Imperial have them only on the top).
  4. Lift the shroud up and out of the bottom shroud attachment clips separating the shroud from the radiator. Avoid damaging the fan.
  5. Remove the upper radiator mounting screws. Disconnect the engine block heater wire, if so equipped.
  6. Remove the air conditioning condenser attaching screws located at the top front of the radiator, if the vehicle is equipped with air conditioning.
  7. Lift the radiator free of the engine compartment.
Care should be taken NOT to damage the radiator cooling fins or water tubes during removal or installation.


To install:
  1. Slide the radiator down into position behind the radiator support.
  2. Attach the air conditioning condenser to the radiator, if so equipped, with a force of approximately 10 lbs. (44 N) to seat the radiator assembly lower rubber isolators in the mount holes provided.
  3. Tighten the radiator mounting screws to 9 ft. lbs. (12 Nm).
  4. Connect the automatic transaxle hoses, if so equipped. Tighten the hose clamps to 35 inch lbs. (4 Nm).
  5. Slide the fan shroud, fan and motor down into the clips on the lower radiator flange. Install new shroud retaining clips.
  6. Install the upper and lower radiator hoses (including the coolant reserve hose).
  7. Plug the fan motor electrical connection and attach the negative (-) battery cable.
  8. Fill the cooling system with coolant (refer to Section 1 for more details).
  9. Operate the engine until it reaches normal operating temperature. Check the cooling system and automatic transaxle for the correct fluid levels. Also check for coolant leaks.
please let me know if i can assist you in any further problems you may encounter with your vehicle.
please do not forget to rate and comment about your experience with fixya today.


Dec 27, 2009 | 1993 Dodge Shadow

1 Answer

Want to replace the radiator on my 1997 ford thunderbird


Radiator Aluminum Core, Crossflow — 3.8L (Base) and 4.6L Engines
Removal
  1. Drain engine cooling system as described. Disconnect upper radiator hose (8260) and lower radiator hose (8286) and radiator overflow hose (8075) from the radiator (8005). Disconnect the transmission oil cooler inlet and outlet lines from the radiator.
  1. Remove cooling fan motor,fan blade (8600) and fan shroud (8146) assembly as described.
  1. Remove radiator upper bracket retaining bolts and remove bracket. Lift radiator from vehicle.
Installation
  1. Position the radiator into the vehicle. Install upper brackets and tighten bolts securely.
  1. Connect the transmission oil cooler lines to the transmission oil cooler fittings.
  1. Install cooling fan motor, fan blade and fan shroud assembly as described.
Engine Cooling Fan Motor, Fan Blade and Fan Shroud Assembly, Electrical Removal
  1. Disconnect (pull apart) the male-female cooling fan motor wiring connector at the side of the fan shroud (8146). Remove the male terminal connector retaining clip from the fan shroud mounting tab.
  1. Remove two fan shroud upper retaining bolts at the radiator tanks.
  1. Lift cooling fan motor/fan blade (8600)/fan shroud assembly past radiator (8005), disengaging fan shroud from two lower retaining clips.
Installation
  1. Follow removal procedure in reverse order.
  1. Tighten fan shroud retaining bolts to 5.2-7.2 Nm (46-63 lb-in).

  2. 10e2638.gif
    8d231fe.gif HOPE THIS HELPS.

    Oct 30, 2009 | 1997 Ford Thunderbird LX

    1 Answer

    How do i replace the radiaor? on this 2005 Hyundai do i remove the intake cover, then the cooling fan, the the motor mount? what?


    Below are instructions and a diagram for removing the radiator from your Santa Fe. There's nothing involving the motor mounts. Best of luck and please post back with any questions or just to rate the solution. Greg

    1. Drain the cooling system. Remove the radiator cap to speed draining.
    2. Remove the inlet hose from the radiator.
    3. Remove the transmission oil cooler lines from the retainer clip at the bottom of the cooling fan shroud.
    4. Remove the fan shroud clip from the condenser tubes.
    5. Remove the bolt that connects the fan shroud to the condenser hold down bracket.
    6. Remove the air deflectors from the top of the radiator.
    7. Remove the cooling fan shroud bolts.
    8. Remove the coolant reservoir hose from the radiator overflow neck.
    9. Remove the radiator upper support brackets and bolts that connect to the fan shroud.
    10. Disconnect the engine cooling fan motors electrical connectors.
    11. Remove the cooling fan motors electrical harness from the fan shroud clips.
    12. Remove the cooling fan shroud.
    13. Remove the outlet hose from the radiator.
    14. Disconnect the transaxle oil cooler pipes from the radiator.
    15. Tilt the top of the radiator rearward.
    16. Remove the condenser hold down bracket from the radiator.
    17. Lift the condenser from the mounting tabs on the radiator and position the condenser aside.
    18. Remove the radiator.
    6db9db4.gif

    Aug 11, 2009 | 2005 Hyundai Santa Fe

    Not finding what you are looking for?
    2006 GMC Sierra Logo

    Related Topics:

    22 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top GMC Experts

    yadayada
    yadayada

    Level 3 Expert

    76070 Answers

    Freddy

    Level 3 Expert

    1311 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Are you a GMC Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...