Question about Ford Cars & Trucks

1 Answer

What colour wire gos to what terminal on ford 1973 coupe starter motor

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 1,209 Answers

Your starter should only have one red wire that goes from the solenoid to the starter.

Posted on Dec 14, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

I think my starter has gone in my 1997 ford expedition. I have all lights etc. but when key is turned i hear a grinding sou nd. My question is, what does the starter look like and where is it.? Is it the...


Here is the picture:
https://www.dragtimes.com/parts/FORD-EXPEDITION-STARTER-46L-1997-1998-NEW_160456310228.html


And this is removal manual:
Starter
Removal & Installation
1. Disconnect the negative battery cable.
2. Raise and safely support the vehicle.
3. Remove the starter terminal cover.
4. Remove the terminal nut and separate the battery starter cable from the starter motor.
5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.
? To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal.
6. Remove the starter motor retaining bolts.
7. Remove the starter motor from the vehicle.
To Install:
8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm).
9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm).
10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.
11. Install the starter solenoid safety cap. If equipped.
12. Lower the vehicle.
13. Connect the negative battery cable.
Start the engine several times to check starter motor

May 19, 2011 | 1997 Ford Expedition

1 Answer

I have coupe 1.6 the starter motor does not turn but battery is fine bump starts ok


do you hear a clicking sound at the starter.if so then the starter needs to be replaced.if not you need to check for voltage at the starter wires the small terminal as that is the wire that comes from the ignition switch,if you have power here then the starter solenoid is bad but you should change the starter anyways.

Apr 14, 2011 | Hyundai Motor S Cars & Trucks

1 Answer

I am looking for wiring diagram for the starter motor for my rolls royce


hi, first thing we need to do is DISCONNECT the BATTERY (NEGATIVE (- sign)) HEAVY LEAD.

the SOLINOID has a HEAVY POSITIVE (+) LEAD this is a BOLT on connection and also (normamlly smaller cable (this cable feeds the car POSITIVE (+)) BOTH BOLT on THE SAME terminal ( ring terminals).

the STARTER MOTOR CONNECTS to the other BOLT ON CONNECTION (SINGLE ring terminal) of the SOLINOID.

the other small wire (s) is the (ignition key position starter motor circuit, the colour RED/WHITE or BLUE/WHITE. this is normally a PUSH-ON connector. if you have a BLACK or BROWN WIRE then this is EARTH (GROUND (-))

testing if this do'nt work. check if BOLT-ON CONNECTIONS are TIGHT by HAND.

the solinoid is a remote HEAVY CONTACT SWITCH and has 2 circuits SWITCHES HEAVY CURRENT up to 700 AMPS. and the CONTOL of the KEY to operate from a small wire. gerry

Sep 13, 2010 | Rolls Royce Silver Spirit Cars & Trucks

1 Answer

Wiring of solnoid for 1997 ford mustang


Big terminal next to motor gets the ground wire. Other big terminal gets the big red hotwire from battery. The little terminal gets the white/pk wire from the starter relay/ignition switch. Always remove the neg batt terminal before hooking up starter, as you can easily get melted wire in your eye down there. I assumed you have the stock setup, but if you have a modified setup with a remote solenoid, please get back to me.

Sep 12, 2010 | Ford Mustang Cars & Trucks

1 Answer

2005 ford windstar Problem starting not enough voltage at the solenoid Starter motor has 12v Starter relay & fuses are good What am I missing?


check battery terminals for corrosion. clean with a wire brush. check starter terminals for corrosion and clean as nessarray. if the connections between the wire and terminal connectors are corroded you may need to replace that wire and terminals.

Mar 28, 2010 | 1998 Ford Windstar

1 Answer

My 92 ford tempo wony start,charged battery, solenoid clicks, pulled starter with wires on, jumped posts and starter spins what now


Most Fords I have worked on use a solonoid. Measure the voltage on the starter motor side when you turn the key. Does it show 12v? The solonoid may be energizing but if the contacts are bad the starter won't get current. Jumping across the two large terminals will also bypass the contacts, see if this will crank the motor. Use a wire the same size as connected to the large terminals. The starter pulls hundreds of amps.

Feb 05, 2010 | Ford Tempo Cars & Trucks

1 Answer

What wire gos on right side small terminal of starter solenoid 1974 dj5


facing the front of the starter, the terminal closest to the engine is the trigger wire for the solenoid. any other small wires would generally be attached to the other small terminal if yours has one. (trigger wire is the only small one that will have full 12v with key turned to start position)

Nov 11, 2009 | 1983 Jeep CJ5

2 Answers

How to remove a starter on a 2002 ford explorer


  1. Disconnect the negative battery cable.
  2. Properly raise and support the vehicle.
b58491e.gif
Disconnect all wires connected to the starter, including this ground wire on the starter mounting bolt stud

  1. Click to Enlarge

    1. Tag and disconnect the wiring at the starter.
    1. WARNING
    1. When detaching the hard-shell connector at the S-terminal, grasp the plastic shell to pull it off. Do not pull on the wire itself. Ensure to pull the connector straight off to prevent damage to the connector and S-terminal. If any part of the connector is damaged, replace the damaged component.
  • daab222.gif
    Remove the starter motor (arrow) mounting bolts . .

    Remove the starter mounting bolts and remove the starter.

    5c220c9.gif
    . . . then remove the starter—be careful, the starter motor can be quite heavy

    To install:
    1. Position the starter motor against the engine and install the mounting bolts. Tighten the mounting bolts to 15–19 ft. lbs. (21–27 Nm).
    2. Install the starter solenoid connector by pushing it straight on. Ensure that the connector locks in position with a notable click.
    Install the starter cable nut to the starter solenoid B-terminal. Tighten the nut to 80–123 inch lbs. (9–14 Nm).
    1. Connect any remaining wiring to the starter motor.
    2. Lower the vehicle.
    3. Connect the negative battery cable.

    Oct 11, 2009 | 2002 Ford Explorer

    1 Answer

    How do i remove starter on 2001 ford f350 dually (7.3 l powerstroke)


    Starter

    Removal & Installation 1. Disconnect the positive and negative battery cables.
    2. Raise and safely support the vehicle.
    3. Remove the starter terminal cover.
    4. Remove the terminal nut and separate the battery starter cable from the starter motor.
    5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.
    ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal.
    6. Remove the starter motor retaining bolts.
    7. Remove the starter motor from the vehicle.
    To Install:
    8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm).
    9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm).
    10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.
    11. Install the starter solenoid safety cap. If equipped.
    12. Lower the vehicle.
    13. Connect the positive and negative battery cables.
    14. Start the engine several times to check starter motor operation

    May 27, 2009 | 2001 Ford F350 Super Duty SuperCab

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    14 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    76164 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    fordexpert

    Level 3 Expert

    5522 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...