Question about 1996 Isuzu Trooper

1 Answer

What way I need to turn to loose a harmonic balancer on Isuzu trooper 1996

Try w the puller and don't work, what direction?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Isuzu Master
  • 1,249 Answers

Counter clockwise with an impact wrench What way I need to turn to loose a harmonic balanc - 25321269-zkea2bktkzr3q3lrmfdlr2m5-4-0.jpg

Posted on Dec 14, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 87 Answers

SOURCE: Harmonic balancer bolt direction for loosening??

CCW , and your going to at least put the new timing belt on and balance to check for compression. you can run an engine without the covers installed or accessories hooked up

Posted on Feb 07, 2009

  • 5 Answers

SOURCE: need to know how much oil for 1996 isuzu trooper

auto box takes 4-5 litres on a service, around 8.5 from dry

Posted on Feb 08, 2009

germcelchar
  • 389 Answers

SOURCE: change a cv boot on a 1996 isuzu trooper

First their are two different front axles in 1996 troopers. Isuzu changed the 4wd system from auto lock hubs to drive control axle.auto lock hube are on the older trooper's with the light and wiper switches on the dash. The same way to change both. Auto hub remove the six hex. screws slide off the hub remove the sirclip from the driveshaft. Newer hub has 6 alan-head screw's again remove them then the hubcap then the sirclip on the shaft and slide off the round spacer. Next 4 bolts from the lower balljoint and the brake's. Pull out the hub until it clear's the shaft remove the inner boot clips slide the inner boot out the shaft. Clean the grease from the end of the axle then with your fingernail feel along any of the 3 tracks in the axle and near the outer end of the track you will find a wirelike split ring slide a screwdriver under the ring and lever it off . Pull out the drive clean off the grease. You will see a sirclip on the end of the joint remove it and slide off the joint. You can replace either boot from that end. The outer joint is held on with a snap ring on the shaft inside the joint and is not easily removed need a hammer and drift to drive off the end and when removed its hard to get the snap ring on the shaft back into its place.You can change both boots from this end as well. Cheers

Posted on Sep 28, 2009

  • 4044 Answers

SOURCE: I have an automatic Isuzu trooper 1996, it shifts wrong

You need to get the transmission serviced. Either the Filter is clogged or something has worn out and needs to be repaired.

Posted on Dec 01, 2009

mabpest
  • 1152 Answers

SOURCE: what type of oil do

I have owned two isuzu trooper's.
and 88 and a 98.
Both having higher mileage I have always used 10W-30.
If your truck is burning oil it may help to get a higher viscosity of oil, but 10W-30 will get the job done.

Posted on Jan 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm trying to remove a harmonic balancer. I've got to the point of taking it off. The pulley remover is placed. But the bolt when completely down only turns the balancer. How to fix please


Are you using a gear puller or an actual harmonic bal. puller? You can use air tools(carefully), or to hold the balancer/pulley still, use a chain wrench with an old belt wrapped around to prevent damage. I would not recommend a 2 or 3 jaw type gear puller.

Oct 17, 2015 | 1996 Buick LeSabre

1 Answer

How to remove harmonic balancer


Buy or borrow a big impact wrench to remove the center bolt. Either use two pry bars to wiggle the pulley off or get a puller from your flaps (favorite local autopartstore). they will also have the socket to rent if you don't have the right one. 25321263-zkea2bktkzr3q3lrmfdlr2m5-4-0.jpg

Dec 14, 2014 | 1996 Isuzu Trooper

1 Answer

How to remove harmonic balancer Isuzu trooper 1996


counter clockwise. if you don't have an impact wrench, watch this video.

Dec 14, 2014 | Isuzu Cars & Trucks

2 Answers

Is it right or left hand thread on harmonic balancer (1996 rodeo)


The harmonic balancer should loosen in the CCW direction. Turn the bolt to counter clock wise direction.To tighten the bolt turn in clock wise direction. -------------- This should help.Thanks.Helpmech.

Apr 06, 2011 | 1996 Isuzu Rodeo

2 Answers

Need to replace the harmonic balancer in a 1994 isuzu rodeo. ( rwd, 3.2 ltr v.6 ). no success so far. is the main bolt reverse threaded? so far i have been attempting to turn it toward the passenger side,...


No, the bolt is not left handed. You do need to turn it counter-clockwise to loosen it. You're probably just spinning the engine when trying to loosen it. I use a 6" c-clamp and attach it behind the balancer in a way that the threaded shaft can lodge up against something so the engine can't turn. Then I use a 3 lb rubber mallet and hit the 1/2" drive rachet on the handle, or put a breaker bar on the end of it and work it loose that way. Once you get the bolt off, you will need to use a pulley puller to get the balancer off.

Mar 19, 2011 | Isuzu Rodeo Cars & Trucks

1 Answer

How to remove the harmonic balancer on a 1995 dodge intrepid 3.5


There is a nut in the center of the balancer... loosening may require an "impact" or a sharp blow with a hammer to begin to loosen the nut. Once loose, you can use a harmonic balancer puller (rentable at a local rental yard) Since its a very tight fit you'll need the puller to persuade it loose from the crankshaft.... watch your knuckles...

Oct 14, 2009 | 1995 Dodge Intrepid

1 Answer

I need a how to to change harmonic balancer for 1995 nissan maxima. step by step


First remove right front tire and support vehicle with a jack stand. Remove splash guard lower portion near the harmonic balancer. Remove all drive belts. First remove the A/C alternator belt. Loosen the 14mm bolt at the front of the belt tenioner and then loosen the tensioner bolt (it is the one that stands out, you use a socket on it.). The power steering adjuster bolt with be gained from the bottom. It has a 12mm bolt head on it. You will break the jamb bolt loose first and then loosen the adjusting bolt. Pull down on the belt the help move it after you've loosened it some.Then remove harmonic balancer bolt (19mm).If the harmonic balancer will not slide off the crankshaft then use a two finger gear puller. Place the harmonic balancer bolt back in the crankshaft but do not tighten it. Leave it about a half inch from being all the way in. Next place the puller onto the harmonic balancer (one finger on each side securely press into the belt groove. The center puller bolt will rest against the harmonic balancer bolt head. Tighten the puller bolt and make sure the harmonice balancer bolt does not turn. The balancer should come off at this point.

Aug 26, 2009 | Nissan Maxima Cars & Trucks

1 Answer

Harmonic balancer bolt direction for loosening??


CCW , and your going to at least put the new timing belt on and balance to check for compression. you can run an engine without the covers installed or accessories hooked up

Feb 05, 2009 | 1996 Isuzu Rodeo

Not finding what you are looking for?
1996 Isuzu Trooper Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14379 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...