Question about 2000 Toyota Camry Solara
Electrically (old post)
electric is easy with schematics of both
alldata.com,. easy peasy.
Posted on Jan 19, 2015
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Look at the back side of the headlamp assembly. There are a couple of ears that stick out, right above a small silver toothed wheel. Using a suitably long phillips screwdriver, insert the driver down into the 2 small ears, and then the screwdriver should contact the small toothed wheel. The ears provide the proper support for the screwdriver to mesh with the toothed gear. Spin the screwdriver, and the toothed gear should spin, also. Rotate the driver in whatever direction to adjust the lamp beam. This will gibe you what you need. Hope this helps; any questions; please repost.
Posted on Oct 10, 2008
check for voltage at the lamps themselves. If no voltage is present, check headlamp relay,.Rarely it could also be the multi-function switch, but don't go there first! Also, did you try a new bulb?(s)
Posted on Dec 13, 2008
Door scraper rubbers stiff tripping the motors protective circuit (anti-crush, to stop chopping off fingers, heads etc)
Try cleaning the glass inside and out with household window clear or a White spirit etc then spray silicone spray on a rag, wipe over the glass then try the window operation.
Posted on Nov 18, 2009
It easy ! You need a philips and flat screw driver,8" X 4" block of wood and a needle nose pliar.
Use flat screw driver and pry out the two or three dust covers for the arm rest screws then use philips and remove the screws. Next use the flat screw driver and pry out the black plastic mirror cover from the inside of the door. Pry out the switch panel ( aka master switch panel) with the flat screw driver and disconnect it. On the side of the door panel just above the striker is this plastic push pull typeof a hold in screw. Use flat screw driver to get it to move a little then pull it out with the needle nose. Depending on which door your doing if you have a map folder ( driver or front passenger door) in the door there are two more screw to remove on the bottom of the door.
Now the inside door handle is tricky it comes out in two pieces. Use philips and get the only hold down screw you see out.( you may have to pry out al ittle screw cover first) Now the handle cover is removed by placeing the flat screw driver on the rear of the outside of the cover top and on the outside rear bottom to release the tangs that are holding it onto the panel.Pry it out lightly you may have to place the screw driver over the top of the door release button and pry that way. Don't loose your cool its a pain but it will fall out. Once its removed unhook the panel.
Next lift the plastic cover and remove the six gold bolts first(For motor and regulator) Then push the window down till you see the two bolts holding the window to the regulator .Remove them, BEFORE YOU PULL OUT THE MOTOR AND REGULATOR YOU WILL SEE TWO TANGS THAT HELP HOLD THE REGULATOR AND MOTOR TO THE DOOR MARK THE RELOCATION , NOW pull out the motor and regulator have an assistant hold up the glass while you place the two blocks of wood to hold up the window. Now order your regulator and installation is in reverse. Good luck kate. Keep me posted.
Posted on Apr 22, 2010
Tips for a great answer:
Oct 19, 2014 | 2000 Toyota Camry Solara
Jun 17, 2014 | 2000 Toyota Camry Solara
Apr 10, 2013 | 2000 Toyota Camry Solara
Apr 03, 2011 | Toyota Solara Cars & Trucks
Apr 01, 2010 | 2000 Toyota Camry Solara
Feb 23, 2010 | 2003 Toyota Camry Solara
57 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: