Question about 1995 Chrysler Cirrus

Open Question

95 cirrus lx. Key codes 12,71,33,23. Where do I start on 71 and is 12 a problem or just not running?

I have installed a new battery, and the ecm was troubleshooted ,reflashed ,and reprogrammed.Next I will check the ground wires but I don't know how to check the low voltage.

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

gordb32750
  • 27 Answers

SOURCE: 95 cirrus lx 12,71,33,23 update. Engine runs great but engine lite won't go out for smog

how are you reading these codes? if you have an OBDII code reader then you should get a 4 digit code. you can go here to learn what they mean
http://engine-codes.com/search_codes.php?q=33

Posted on Dec 14, 2014

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 96 Chrysler Cirrus lX its starts up but turn right off what could it be,?


if it starts and runs while you have the key in the start position but stops when the key returns to the run position it is probably a faulty ignition switch that is breaking the run circuit in the switch

Oct 11, 2015 | Chrysler Cars & Trucks

1 Answer

Where is the anti theft light o a 2008 nissan xterra


It will be on the dashboard usually looks like a padlock. The ecm needs to be coded to the key and possibly to the car other ecus and dashboard as that is usually the canbus controller . If u have only changed the ecm the car will not start

Jan 23, 2015 | 2008 Nissan Xterra

1 Answer

95 cirrus lx 12,71,33,23 update. Engine runs great but engine lite won't go out for smog


how are you reading these codes? if you have an OBDII code reader then you should get a 4 digit code. you can go here to learn what they mean
http://engine-codes.com/search_codes.php?q=33

Dec 13, 2014 | 1995 Chrysler Cirrus

1 Answer

Where is starter relay switch on a 95 cirrus lx 2.5 motor located at


If the starter spins but does not engage the flywheel, either the starter is faulty or there are teeth missing from the flywheel.

Sep 01, 2014 | Cars & Trucks

1 Answer

Just installed new ecm on 04 gmc envoy, now engine wont start. everything else works. what should i do?


when ever you replace ECM computer, you must take out your CHIP , to put it into your new ECM. did you do this ?????? if not your engine will not run ,even with GOD turning the key .

Feb 01, 2013 | 2004 GMC Envoy

3 Answers

1995 chrysler cirrus lx-the engine cuts off when moving-driving


I have a '95 Cirrus LX 2.5L V6 (with 150k miles) that has been having the same problem -- it just shuts off unexpectedly while driving and then fails to start right afterward. No "Check Engine" light beforehand and no fault codes were stored. After setting for a while, the car would eventually start again. Initially this problem happened only seldomly but over several months it gradually became more frequent.

After doing a lot of research on the Internet and troubleshooting with the Haynes manual, the prime suspects were as follows:
1) Crankshaft Position Sensor (mounted onto the engine block under the distributor). I replaced this and the car started but it didn't last long before it abruptly quit again. This time, whatever was degrading finally broke for good; the car would no longer start even after sitting for a couple days.

2) Camshaft Position sensor and/or ignition coil -- (both are in the distributor on the 95 Cirrus LX 2.5L V6). I replaced the distributor (cost about $225). The car still would not start, though!

Using the electrical diagrams in the Haynes manual, I began troubleshooting and found that all of the top three mentioned items use the same +8VDC from pin 44 of the Powertrain Control Module (PCM). I was only reading +4.88VDC -- way too low for for the two 'Hall Effect' solid-state sensors to work properly.

I didn't want to spend hundreds of dollars buying a new PCM if I wasn't absolutely sure it was the problem so I took out my PCM (it's up front between the fuse box and the air cleaner on the driver's side and can be removed fairly easily). Since this is a single-board electronic device, being an electronics technician, I tried an old trick and froze the PCM for more than 12 hours so the circuit board and solder joints would contract and make a better connection. I then reinstalled the PCM and tried starting the engine -- and it fired right up and ran smoothly.

So, the PCM (P/N PO4606064) ended up being my problem.

NOTE: There are two replacement models of PCM for this car. One model is for cars with "Firm Feel Suspension (FFS)" and another model for those without; mine DOES NOT HAVE FFS. Make sure you get the correct one.
Also, on one of the threads on the Internet for another person having this same problem, a Master Mechanic stated that 'Firm Feel Suspension (FFS)' was the same thing as "Speed Sensitive (power-assisted) Steering (SSS)". I confirmed with the Chrysler experts that THIS IS NOT THE CASE! They are separate things -- according to my VIN, my car does not have FFS but it has SSS.

Feb 25, 2010 | 1995 Chrysler Cirrus

1 Answer

My car died code 1255


that is two codes, niether mean any problem, here are the difinitions,
12 Battery Disconnect Direct Battery input to PCM disconnected within last 50 ignition key-on cycles. Normal if battery has been disconnected, otherwise check battery power and ground connections


A DTC 55 is used to end all DTC messages. This code does not show on the DRB tool and indicates a completion of the stored codes on the Malfunction Indicator Lamp (check engine lamp).

Aug 14, 2009 | 1996 Plymouth Neon

1 Answer

Check engine light


Code 12.................Problem with the battery connection. Direct battery input to PCM disconnected within the last 50 ignition key-on cycles.

either a loose connection or the battery dead or removed within 50 last times you turned on the car, check battery terminals for corrosion or loose connector, and check the earth wire for corrosion, the code will dissapear by itself if the power is not removed again

Apr 11, 2009 | 1995 Chrysler Cirrus

1 Answer

My '95 Thunderbird wil turn over but randomly will not start.


Your crank sensor may be really dirty and can't get a good signal from the reluctor near the balancer. Check the wiring harness to it as well. You may need a new crank sensor.

Nov 01, 2008 | 1995 Ford Thunderbird

Not finding what you are looking for?
1995 Chrysler Cirrus Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...