Question about Cars & Trucks

1 Answer

My mb s 550 2007 headlamps is on all time.Do'not matter swich is on automatic position,or is off position.What is problem?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,368 Answers

Welded relay contact or shorted switch.

Posted on Dec 13, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Saturn aura wont start after trying to put rt.low lowbeam replacement


On the inside of the lid is a diagram .
The headlamps may be turned ON 2 different ways. First, when the driver places the headlamp switch in the HEADLAMP position, for normal operation. Second, with the headlamp switch placed in the AUTO position, for automatic lamp control (ALC). During ALC, the headlamps will be OFF in daylight conditions, or low beam operation in low light conditions. Battery positive voltage is supplied to the low beam relay and the high beam relay in the underhood fuse block. When low beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the low beam relay. This activates the relay and the relay supplies voltage to the left hand low beam headlamp through the LH LOW BEAM fuse and to the right hand low beam headlamp through the RH LOW BEAM fuse. Ground for the left hand low beam headlamp is provided at G101. Ground for the right hand low beam headlamp is provided at G102. When high beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the high beam relay. This activates the relay and the relay supplies voltage to the left hand high beam headlamp through the LH HIGH BEAM fuse and to the right hand high beam headlamp through the RH HIGH BEAM fuse. Ground for the left hand high beam headlamp is provided at G101. Ground for the right hand high beam headlamp is provided at G102.

Aug 14, 2017 | Saturn Cars & Trucks

1 Answer

2000. Where is fuse for tail lights?


Do your headlamps work ?
Park/Marker/License/Tail Lamps
Voltage is applied to the turn/headlamp switch at all times. When the turn/headlamp switch is in the PARK or the HEAD position, voltage is applied to the following components:
?€¢
The park lamps


?€¢
The marker lamps


?€¢
The tail lamps


?€¢
The license lamp

The front marker lamps are grounded through the turn filament of the respective front park/turn lamp. The front marker lamps light as a result.
The automatic lamp control function turns on the park lamps and the headlamps. This action occurs when the ambient light sensor determines that the exterior lamps should be turned ON based on the amount of available light. When the BCM grounds the park lamp relay, voltage is supplied directly to the park lamps, bypassing the turn/headlamp switch assembly. When this action occurs, the following conditions exist:
?€¢
The automatic lamp control relay is grounded.


?€¢
The headlamps turn ON. Refer to Headlights/Daytime Running Lights (DRL) Circuit Description .

The lamps turn OFF when the BCM does not ground the park lamp relay or the automatic lamp control relay. This action is caused by the following conditions:
?€¢
The available light reaches a predetermined level.


?€¢
The ignition switch is turned to the OFF position

Mar 31, 2016 | Pontiac Grand Am Cars & Trucks

1 Answer

No low beam. Good high beam. No day lights. What's wrong?


No on the fuse . The LH HDLP and RH HDLP fuse in the fuse block - under hood, supply battery positive voltage to both low and high beam lamps at all times. For manual operation, when the headlamp switch is in the ON position, the headlamp switch supplies ground directly to the headlamps and to the body control module (BCM) on the headlamp low or high beam signal circuit, depending on the position of the headlamp dimmer switch. The BCM uses this signal to determine if the conditions are present to illuminate the daytime running lamps or park lamps.
The headlamps may be turned on 2 different ways. First, when the driver places the headlamp switch in the ON position, for manual operation. Second, with the headlamp switch placed in the OFF position activating automatic lamp control (ALC).For ALC operation, the BCM receives a signal from the ambient light sensor indicating a low or high ambient, outside, light level. Under low light conditions the BCM grounds the headlamp relay control circuit energizing the headlamp control relay. The now closed relay supplies ground through the headlamp switch to the headlamps and the BCM on the headlamp low or high beam signal circuit, depending on the position of the headlamp dimmer switch. When the BCM grounds the headlamp relay control circuit it also grounds the park lamp relay control circuit illuminating the park lamps. The headlamp relay is grounded at G203.
Daytime Running Lamps (DRL)
The low beam headlamps operate at reduced intensity when in daytime running lamps (DRL) mode. The ground circuit to the switch side of the DRL relay has a resistor in-line to reduce the intensity of the low beam headlamps for DRL operation. The body control module (BCM) receives a signal from the ambient light sensor indicating a low or high ambient, outside, light level. Under daylight conditions the BCM grounds the DRL relay control circuit energizing the DRL control relay. The now closed relay supplies ground directly to the low beam headlamps and to the BCM on the headlamp low beam signal circuit. The low beam headlamps now illuminate with reduced intensity. The DRL relay is grounded at G203. Any time the headlamps are illuminated the DRL will not illuminate. Manual park lamps do not effect DRL operation.

Feb 23, 2016 | 2005 Chevrolet Equinox LS

1 Answer

Why don't lights work?


Both the headlight switch and the BCM provide a ground, or control circuit, to the headlight relay coil circuit for manual or automatic headlamp operation. When you place the headlamp switch in the OFF position, and the ambient light sensor indicates low light conditions, the BCM energizes the headlamp relay for low beam operation. You may switch the headlights to high beam by pulling the dimmer switch handle toward you until the dimmer switch is activated. When the dimmer switch is placed in the HIGH position, the indicator lamp input to the BCM is pulled low. The BCM then sends a class 2 message to the instrument cluster in order to illuminate the high beam indicator lamp.
Low and High Beams Headlamps Inoperative ?
Replace the headlamp switch. Refer to Headlamp Switch Replacement .
Did you check the headlamp relay ? Location ,left instrument panel
Did

Nov 11, 2015 | 2001 Chevrolet Monte Carlo

1 Answer

2006 buick allure , automatic low beams do not come on when key starts car


Headlamps
You can use the headlamps two different ways.
?€¢
Place the headlamp switch in the HEAD position for normal operations


?€¢
Place the headlamp switch in the OFF position for automatic lamp control (ALC) operation. During ALC the low beam headlamps are ON for daytime running lamp (DRL) operation in daylight conditions at reduced intensity or low beam headlamps ON at full intensity with exterior park lamps ON in low light conditions. The ambient light sensor is a light-sensitive transistor that varies its voltage signal to the body control module (BCM) in response to changes in the outside (ambient) light level. When the BCM receives this signal the BCM turns ON just the low beam headlamps at reduced intensity for the daytime running lamp (DRL) operation. A resistor wire is used (CKT312) to reduced the voltage which reduces the light intensity for the DRL's function. The ambient light sensor can also turn ON the low beam headlamps and the exterior lamps for automatic lamp control (ALC). Any function or condition that turns ON the headlamps will cancel the DRL operation (this means no reduced voltage to the low beam lights). Thirty seconds after you start the engine with the headlamp switch in the OFF position, the DRL will perform one of two actions:
?€¢
Illuminate the low beam headlamps at reduced intensity in daylight conditions


?€¢
Illuminate the low beam headlamps and exterior park lamps for low light conditions

The DRL operates when the ignition switch is in the RUN position, the parking brake is not set and the transmission is not in the PARK position When these conditions are met and the DRL ambient light sensor indicates daylight conditions the DRL will illuminate
Should have BCM scanned for DTC'S - diagnostic trouble codes , could have DTC'S stored in memory !
DTC B2645 Ambient Light Circuit
The body control module (BCM) monitors the ambient light sensor signal circuit in order to determine if the daytime running lights (DRL) or the auto headlights (ALC) should be turned ON in the AUTO mode. When the BCM senses the ambient light sensor voltage is between 1.75-4.9 volts, either the DRL will be commanded ON or the ALC will be commanded ON.

  1. Turn ON the headlamps.
  2. Ensure that the headlamp dimmer switch is in the LOW position.
Do both low beam headlamps illuminate?
Is only one low beam headlamp inoperative? YES / NO
IF no
  1. Disconnect the lamps switch assembly.
  2. Install a jumper between the headlamp switch headlamps ON signal circuit and ground.
Do the low beam headlamps illuminate?
Do the low beam headlamps illuminate?
Go to Step 18
Go to Step 7

7

  1. Remove the headlamp module.
  2. Install a fused jumper between battery positive voltage and the switched low beam voltage supply circuit.
Do the low beam headlamps illuminate?
Go to Step 8
Go to Step 11

8

Test for the following in the headlamp module control circuit:
?€¢
An open


?€¢
A poor connection


?€¢
A short to ground

Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 10

9

Inspect for a poor connection at the harness connector of the lamp switch assembly. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 14

10

Inspect for a poor connection at the headlamp module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 15

11

Test for a short to ground in the low beam voltage supply circuit. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 12

12

Inspect for a poor connection at the harness connector of the underhood fuse block. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 17

13

Inspect the inoperative low beam headlamp voltage supply and ground circuit for a high resistance, a short to ground, or an open. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 16

14

Replace the lamp switch assembly. Refer to Headlamp Switch Replacement .
Did you complete the replacement?
Go to Step 19
--

15

Replace the headlamp module. Refer to Relay Replacement in Wiring Systems.
Did you complete the replacement?
Go to Step 19
--

16

Replace the inoperative low beam headlamp. Refer to Headlamp Assembly or Headlamp Bulb Replacement .
Did you complete the replacement?
Go to Step 19
--

17

Replace the underhood fuse block. Refer to Testing for Intermittent Conditions and Poor Connections .
Did you complete the replacement?
Go to Step 19
--

18

Replace the BCM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?
Go to Step 19
--

19

Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 3

IF

Sep 30, 2015 | Buick Cars & Trucks

1 Answer

Why does my 1999 chevy malibu headlights turn on by them self in middle of night


You have a gremlin ! No , just kidding . No it's not the ignition switch ! The headlamps right an left have there own fuse in the under hood fuse box . LH HDLP - RH HDLP . Power direct to the head lamps an they ground through the headlamp switch when placed in high or low beams . Next time they come on wiggle the headlamp switch an see if they go out ! Does your vehicle have auto lights ? Day time running lamps ? The BCM - body control module controls Automatic lamp control !
Battery voltage is applied to the headlamp bulbs at all times. The headlamps are controlled by supplying the ground for the lamps through the turn/headlamp switch assembly or the body control module (BCM). When the turn/headlamp switch is in the ON position, the ground is supplied through CKT 150.
The BCM controls the daytime running lamps (DRL). The system allows the headlamps to operate at a reduced intensity under the following conditions:
?€¢
The engine is running.


?€¢
The transaxle is not in the PARK position.


?€¢
The normal headlamps are turned OFF.

The BCM activates the system by grounding CKT 592. This action energizes the DRL relay. This condition allows a reduced voltage to flow to the headlamps. When the headlamp switch is turned to ON, the headlamps operate normally.
The parking brake provides an input to the BCM. When the parking brake is engaged, the DRL remain disabled until the parking brake is disengaged.

May 30, 2015 | 1999 Chevrolet Malibu

1 Answer

Locate the ambient light sensor


Automatic Headlamps- Vehicles with the automatic headlamps option are equipped with a unique headlamp switch that includes an A (Automatic) position and have a sun load sensor located on the top of the instrument panel to sense ambient light levels. When the A position of the headlamp switch is selected while the engine is running, the headlamps are turned ON and OFF automatically as ambient light levels dictate.

Feb 08, 2015 | Cars & Trucks

2 Answers

1999 oldsmobile 88 headlights wont shut off


Pull this circuit breaker till you can find the problem. Check for applicable trouble codes. You have a lighting control module, I can't troubleshoot that component from here.
headlamp circuit breaker-aqqcxoafxh3vrrogaagbglgs-1-0.jpg

Apr 29, 2017 | 1999 Oldsmobile 88

1 Answer

I have low beam but no high beam. relay on new harness is good but it connects to the old harness. i put the new harnes on so i could have high beam on drivers side it worked for a while but stopped. most...


What relay's ?
The instrument cluster controls the headlamp systems that include daytime running lamps (DRL). The system allows the headlamps to operate at a reduced intensity when all of the following conditions apply:
• The engine is running.
• The transaxle is not in the PARK position.
• The normal headlamps are not on.
The instrument cluster turns the DRL system on by grounding CKT 592, thereby energizing the DRL relay. This action allows a reduced voltage of 6 volts to flow across the headlamps. If the vehicle has the optional fog lamps, the fog lamp relay will also be energized. The park lamps will turn on and the fog lamps will operate normally. When the headlamp switch is turned to the ON position, the instrument cluster allows normal headlamp operation.
The instrument cluster also has an input from the park brake. If the park brake is in the ON position, the DRL will remain disabled until the park brake is placed in the OFF position. On vehicles with an automatic transaxle, the instrument cluster will disable the DRL until the transaxle has been taken out of the PARK position.

Headlamps Inoperative - High Beams
Step
Action
Value(s)
Yes
No
1
Did you perform the Daytime Running Lamps (DRL) System Check?
--
YES - Go to Step 2
NO - Go to Daytime Running Lights (DRL) System Check
2
Disconnect the turn/hazard headlamp switch connector C1.
Connect the fused jumper between terminal B of the turn/hazard headlamp switch assembly harness connector C1 and ground.
Do the high beam headlamps operate?
--
YES - Go to Step 3
NO - Go to Step 4
3
Replace the turn/hazard headlamp switch assembly.
YES - Did you complete the repair?
--
NO - Go to Daytime Running Lights (DRL) System Check
--
4
Repair the open in CKT 1200 between the turn/hazard headlamp switch assembly. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair?
--
Go to Daytime Running Lights (DRL) System Check
--

Jul 01, 2017 | 1998 Chevrolet Cavalier

1 Answer

Headlamps won't light up


The headlamps are in manual mode. you must change in the computer the option of the headlights to automatic and then check the manual control of the lights that should be in the complete left position with the orange light on.

Aug 05, 2008 | 2004 Chevrolet TrailBlazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...