Question about Cars & Trucks

1 Answer

I have a slayer pro and I thought the cluch was way to tight but I loosened it...the truck won't roll backwards...and when I start it the wheels spin with the revs of the motor so what could it be ..all the drive line is good...could it be the gear mesh?...or tranny problem?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 29 Answers

I teally think its a prob with ur gears..

Posted on Dec 13, 2014

  • brad mccrindle Dec 15, 2014

    Yeah I think I found out what is was a started the truck and picked it up and held it wide open and after that is when everything got tight....so I'm pretty sure that the motor shifted and locked up the mesh between the bell and spur gear....thanks for your help

  • brad mccrindle Dec 15, 2014

    Yeah I think I found out what is was a started the truck and picked it up and held it wide open and after that is when everything got tight....so I'm pretty sure that the motor shifted and locked up the mesh between the bell and spur gear....thanks for your help..and also the motor bults were not that tight and there was no locktight on them

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changed rear bearing on 2001 Honda accord now it is tight and holding back when you drive


Is it the rear wheel bearing you have replaced?
If so, please jack up the rear wheel you fixed and try to spin the wheel by hand.
If it is tight, you will need to loosen the nut as it is too tight.
If it is loose, you may have your brakes too tight.
God bless your efforts.

Nov 27, 2015 | 2001 Honda Accord

2 Answers

Front breaks lock up,while driving,park for a few minutes,breaks are fine


Could be that the callipers are jamming or the wheel is running tight. Check for wheel spin with the front wheels off the ground, they should spin with minimum effort. Could also be something wrong with the master cylinder. It may not be releasing properly and slowly building pressure to lock the brakes. After sitting for a while, it returns to normal position and releases the brakes. Mt Ford had a dud wheel bearing which would intermittently start to seize. When this happened, the anti lock braking system thought that the wheel was about to lock and would throw the brakes on and off without warning... Check your wheel bearings too.

Apr 13, 2015 | 2007 Chevrolet Avalanche LTZ

1 Answer

2011 sonata shifter won't lock into place


Do you have a warranty?If so take it back,it may have a recall.

Dec 18, 2012 | 2011 Hyundai Sonata

1 Answer

My tire is tilted slightly inward at the top on out toward the bottom, makes a noise similar to brake pads rubbing ( Yes, I have changed my brake pads... ;-)) and feels like the car is being held back from...


Worn wheel bearing, jack up front to allow wheel to spin. Hold wheel and try to rocck it top to bottom and left to right. get someone under car to look at any play at suspension ball joints or bewaring.

Oct 24, 2012 | Cars & Trucks

1 Answer

Front wheel bearing clearance/adjustment


Adjust the castellated nut by lightly tightening it and spinning the wheel. Now loosen it until the casteallations line up with the axle's crossdrilled hole. Too loose is better than too tight.

Aug 08, 2012 | 2000 Mercedes-Benz CLK

3 Answers

How do you know if your front wheel bearings are going out i have a 1967 camaro


Jack up the vehicle, grab the tire from the top and bottom....side to side and try to move it. If the tire and rim move in any dirrection while observing the hib, your wheel bearings are in need of replacement. You may want to remove the hib assembly and inspect. It is not a real diffucult job to perform, and replacing the bearings and seals would not hurt or harm a thing if they are suspect.

Mar 20, 2010 | Chevrolet Camaro Cars & Trucks

1 Answer

REPLACE STARTER ON 1995 CHEVY S-10PU 4.3 LTR


step1 Turn the truck off and disconnect the battery. Lift the car with a jack and place jack stands under the frame of the truck. Block the rear wheels to prevent the truck from rolling backwards. Step2 Locate the starter and remove the wires connected to it. Mark them so you know which is positive and which is negative so you can reconnect them accordingly. Step3 Remove the bolts holding the starter in place. There are usually two or three bolts holding the starter. Step4 Pull the starter out of its position and remove it from the truck. Some other parts may need to be loosened or removed for the starter to be removed from the truck. Remember what parts are removed or loosened. Step5 Put the new starter in the truck by installing it the same way the old starter was removed. Tighten the bolts slightly, connect the wires to the starter and then tighten the bolts completely. Step6 Replace any other parts in the truck that were removed or loosened. Lower the truck from the jack stands, remove the blocks from the rear wheelsmag-glass_10x10.gif and reconnect the battery. Start the car to make sure everything is working properly.

Feb 25, 2009 | 1995 Chevrolet S-10 CA Edition

1 Answer

Rear brake drums


a lot of brute force is needed or invest in a hub puller

Nov 22, 2008 | 1994 Pontiac Bonneville

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...