Question about Cars & Trucks

1 Answer

What to do when your remote quits working that cranks your truck

Cleaning cables and checked fuses

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 90 Answers

The batteries in your remote are probably dead. Put in new batteries. Just use the key until you get new batteries.

Posted on Dec 13, 2014

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
cobra777
  • 80 Answers

SOURCE: keyless remotes not working

Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:

  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Posted on Jun 06, 2010

Testimonial: "Great advice. This fix worked great. "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What to do when my remote quits workingto crank my truck


could be the transmitter or remote starter itself, check the connections on your starter, they use cheap pinch on connectors that let your wires corrode and they also disolve because they are made from cheap metal, they can also destroy your ECU and cost you a fortune, some remote companys can try to start your vehicle remotlely via satellite, you can remove the switch they put on your starter and see if it works with 12 volt power, use a test light or a volt meter to see if it opens or closes, if it does its your transmitter for sure

Dec 13, 2014 | Cars & Trucks

1 Answer

What to do when your remote quits working that cranks your truck


Replace the battery in the fob. Have the fob check to see if it is working. If the receiver is bad replace the system or take it out. If you don't take it out, eventually it will mess up the security system and you won't be able to start the car with the key. I take them out all the time, when I see them. Starts the car every time..

Dec 13, 2014 | Cars & Trucks

1 Answer

My dash has quit working on my 2001 dodge caravan


Have you ever had any work done in that area? Check all fuses and the back side of the fuse cover points you to what each fuse does. If you've had damage to the dash it is quite likely where your problem is.

Feb 01, 2013 | 2001 Dodge Grand Caravan

2 Answers

The remote locking fob will not work on my 94 sovereign 4 litre I have a warning on the dash saying fuse 2 but I have checked fuse 2 and it is ok how do I re-program the remote? mike


what about the spare fob?? i have two with my sovereign ,try cleaning the battery connections as well then bend them up a bit and use a bit of vasaline on the connections ,works wonders

Dec 24, 2009 | 1994 Jaguar XJ6

1 Answer

2002 Yukon won't start


try cleaning battery cables if not that check starter

Apr 12, 2009 | 2002 GMC Yukon Denali

1 Answer

Crank but will not start


yes .check your timeing belt

Dec 23, 2008 | 2006 Mazda 6

1 Answer

2004 tahoe


yes or damage to the cars computer chances are that you have a blown fuse or loosecables check all connections and be very careful not to damage any airbag cables

May 20, 2008 | 2004 Chevrolet Tahoe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...