Question about 2000 Nissan Quest

2 Answers

Engine misses when you excelerate. when its hot engine wont start

Replaced distributer cap & rotor

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 14,585 Answers

It could be to much air, not enough fuel. Or to much fuel, not enough air. Most likely the first, unless you notice a lot of black smoke when accelerating. Check engine light on? Also could be the catalytic converter/s. Have the codes read. repost.

Posted on Dec 13, 2014

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It the ignition coil inside the distributor. I have the same problem with my 2000 Nissan Quest. After I replace the distributor, my car runs great now.

Posted on Jan 05, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 93 Ford Ranger 3.0 missing when hot. I have replaced the timing belt, plugs, wires, distributer cap, and rotor button.


Compression good on all 6 cylinders when the engine is hot ?
If yes, it could be an injector.

Sep 07, 2015 | Ford Cars & Trucks

1 Answer

1988 ford bronco11 have feul,but no fire from distributor to coil


with distributer cap off have someone crank engine and see if your rotor is turning if not repair distributer or replace.

Apr 05, 2014 | 1988 Ford Bronco II

1 Answer

Replaced plugs , wires, distributer cap, rotor, no. 3 cyl. not hitting all the time


The problem could be related to the fuel injector instead of the ignition system.

Jan 31, 2013 | 1990 Toyota Camry

1 Answer

I changed my dist. cap & rotor wireleads and plugs. The truck still wont start what am i missing?


What the mechanic said does not make sence, the first thing you need to do is start from basics. Check the spindle on the distributer moves as you turn the engine over. If it does replace the top and connect the lead to a plug you have removed, then earth it on the motor. (DO NOT HOLD IT OR THE CABLE) . Turn over the engine again, it should spark ( the plug). Then check the timing from scratch. If you want to know in detail how to check the timing, post again.

May 20, 2012 | 1996 GMC Sonoma

1 Answer

I changed my distributer cap and rotor, On my 1990 Cherokee 4.0 inline 6 ,I replaced plugs followed 153624 and now it wont start ?? i matched # 1 on the block to #1 on the distributer cap etc .. turns...


if that distributor has ever been out, it may not line up on #1. check to make sure the coil wire is connected tight on both the coil and the cap.

Mar 02, 2011 | 1990 Jeep Cherokee Limited

3 Answers

Car wont start, not getting spark


crankshaft sensor, or computer on toyotas then it was usually the distributor or the computer, but the crankshaft sensor might be bad too thats what helps to get you spark.

Jul 31, 2010 | 1991 Toyota Corolla

2 Answers

Just replaced engine in my 97 its a vortec brought it to tdc put in distributar it turns over and tries to start but wont i turn it just a little it acts better but i cant move it far enough


take the spark plug out of the #1 cylinder and turn the engine by hand until the piston is at the top dead center of its stroke (put a screw driver in the hole and you should be able to tell when its all the way up). now pull the cap off the distributer the rotor should be pointing at the #1 cylinder wire. if not then the distributer is in the wrong possition. remove the distributer and point the rotor in the correct possition(#1 cylinder) and place the distributer back in.also if this is a used engine replace the cap,rotor plugs and wires.the truck should start. Hope this helps you out.

Mar 14, 2010 | 2002 GMC Sierra C/K1500

1 Answer

Replaced engine. car turns but wont start. power


have you checked that the points in the distributer are set ok and havent closed or burnt,as this is what makes the coil spark the ht lead to the distributer cap to the rotor arm then to the plug leads.
hope this helps

Aug 02, 2009 | Ford Contour Cars & Trucks

1 Answer

95 nissan v6


Hi kellymcmeen

I think that you may have missed replacing the weather gasket....fits between the cap and the distributer body.

Best regards Johngee10

Oct 11, 2008 | 1997 Nissan Pickup

Not finding what you are looking for?
2000 Nissan Quest Logo

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...