Question about Cars & Trucks

1 Answer

1987 nissan d 21 4x4 4cylinder z motor need torque specs for flywheel to crank and presher plat to flywheel

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 5,313 Answers

It amazes me how many questions are asked about torque specs. Anyone going into an engine deep enough to need them should be working from a shop manual. I'm 67 years old and been wrenching since I was 14. Over the years I've bought more than 100 vehicle specific books and I still will not tackle a new type car or truck without a shop manual. They are cheap and full of tips and tricks to insure you don't screw something up. Use them folks!

Posted on Dec 12, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Torque spec for flywheel bolt: Isuzu 2.5 diesel engine

normally 110 nueton metres. use nut lock and once you have torqued you will feel if you have to tighten it a bit more.

Posted on Aug 15, 2008

emissionwiz
  • 75797 Answers

SOURCE: i need torque specs for 94 rodeo

flywheel 80-90 foot lbs (new bolts 90), press plate 45 foot lbs

Posted on Feb 14, 2009

joecoolvette
  • 5660 Answers

SOURCE: Bolt torque specs for flywheel, pressure plate,

1.Flywheel - 61 to 69 Foot Pounds
2.Pressure Plate - 25 to 33 Foot Pounds
3.Bell Housing - No specs found. I would say 25 to 35 foot pounds should be sufficient.

Bolts clean on ->flywheel to crank, ->pressure plate to flywheel, and ->bell housing to back of engine, I would use TWO drops of Loctite Red threadlocker, on ALL of these bolts.

Hope you have an alignment tool for your clutch disk when you install it. Auto parts stores sell the plastic one's cheap! Saves a LOT of headaches!

Tighten the pressure plate EVENLY! Snug the bolts down until they just TOUCH, then go in a criss-cross pattern when tightening. Do the tightening in incremental stages! You turn one bolt one thread, you go across to the opposite side, and turn that bolt one thread. Keep criss-crossing so the pressure plate goes down EVENLY. (YES, it's a pain in the keister!)

If NOT, you'll have a warped pressure plate, and it will be junk!
Thanks for letting me say that, I feel better.

Posted on Jul 07, 2009

mindreader
  • 578 Answers

SOURCE: i need the torque specs for a ford 300 inline 6

Tighten all bolts to 10 Lbs, then 20 Lbs, then 35 Lbs.
That should be fine for the 6 cylinder flywheel.

Posted on Oct 10, 2009

wilsodfarm
  • 986 Answers

SOURCE: 04 4.6 mustang, what are the torque specs for the

Flywheel/Driveplate Bolts 59-64 ft. lbs.I hope this helps you,and merry x mas,And please dont forget to vote on this

Posted on Dec 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the torque specs for flywheel bolts on a Nissan NP 200 bakkie. It has a Renault K7M engine - 1600 cc


you will need the torque specifications for the renault engine not nissan
the bolts may be different sizes and incorrect torque readings may snap off the bolts

Dec 17, 2016 | Nissan Cars & Trucks

1 Answer

What is the torque setting for nissan navara v6 4lt2007 flywheel torque


there are 2 sets of torque specs for flywheel bolts as there are 2 different fly wheels in use with different bolts for each
go google and type in--torque specifications for nissan navara flywheel bolts and fins a site relevant to you application
it could be 61-69 ft/lbs a or 90 ft lbs depending on the flywheel and the vehicle 2wd or 4wd

Sep 30, 2015 | Nissan Cars & Trucks

1 Answer

Torque specs on a 1987 Nissan 300 zx 2+2 plenum


If you are referring the the collector the specs are:
Collector cover: 4.3 - 5.8 ft lbs
Collector: 13-16 ft lbs

You should use a torque wrench that is sensitive at low torques. I bought an "inch pound" torque wrench for delicate items like injectors and just convert the foot pounds to inch pounds.

Mar 03, 2015 | 1987 Nissan 300ZX

1 Answer

Nissan frontier starter binds the flywheel


You need to put shims in between the starter and the engine block.You should be able to pick them up at your local auto parts store.

Oct 31, 2012 | Nissan Frontier Cars & Trucks

1 Answer

Need flywheel specs and pressure plate torque specs for 1991 ford f250 460 motor 4x4


flywheel bolt torque 75-85 ft-lbs and pressure plate 15-20 ft-lbs

Apr 08, 2011 | Ford F-250 Cars & Trucks

1 Answer

I need the torque specs for a ford 300 inline 6


Tighten all bolts to 10 Lbs, then 20 Lbs, then 35 Lbs.
That should be fine for the 6 cylinder flywheel.

Oct 08, 2009 | 1997 Ford F150 Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...