Question about Cars & Trucks

1 Answer

How do I tell which heater goes to the throttle body?

What heater hose goes to the throttle base?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 24 Answers

I have no idea what you are working on. That should not matter cause it will still get flow. If it can go either way.

Posted on Dec 11, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is causing it to leak?


If not radiator hoses, what about heater hoses to and from heater core?
You might also have throttle body heater hoses to and from throttle body.
My biggest problem is I can't see anything from here.

Nov 27, 2015 | 2000 Pontiac Montana

1 Answer

2002 4.0l explorer cleaned throttle body but it increase the idle


Is there a vacuum hose off or leaking somewhere? Maybe a throttle body base gasket?

Feb 05, 2012 | 2002 Ford Explorer

3 Answers

Where is the thermostat located grand am 2000?


Under the radiator hose that meets the top of the engine
under the throttlebody if you follow the heater hose from firewall on the driverside toward the engine it goes to the thermostat housing.

To get to the thermostat you need to remove air cleaner box assembly from the throttle body and move it out of the way. Next, remove the nut at the throttle body that holds the steel tube that goes to the heater hose, remove all hoses that connect to this tube and raise it out of the way. Remove the steel line that goes to the radiator surge tank from the thermostat housing. Now the fun part. With a 13MM box end wrench, loosen the lower bolt from the thermostat housing. A 13 mm socket will remove the top bolt. Remove the thermostat cover and remove the thermostat. Reverse to install.

May 13, 2010 | 2000 Pontiac Grand Am GT

1 Answer

How do i remove the heater defroster kit and


Loosen the clips holding the coolant hoses and release them, remove the throttle body by undoing the 4 bolts holding it to the plenum chamber. Discard the gasket & fit a new one on refit. (This is after removing the intake hose, and disconnecting the throttle & cruise control cables. Then undoing the clip securing the breather hose and the multiplug).

Nov 12, 2009 | 1999 Land Rover Discovery

1 Answer

Change thermostat on gm 3400 v6


Drain coolant at the radiator drain. Remove air intake hose and MAF sensor assembly. remove throttle cable bracket and disconnect cable linkage. Remove throttle body bolts and disconnect coolant hoses to throttle body. Loosen heater hose pipe and remove heater hose from rear of pipe. Remove radiator hose from thermostat housing. Remove top thermostat housing bolt. Loosen and almost remove lower thermostat bolt. You will need to slide your wrench and hand under the exhaust crossover pipe to gain access. Loosen the bolt until you can remove the thermostat housing, it should be slotted to clear the bolt. Replace the thermostat and reassemble. Bleed cooling system using the two bleed screws (one on thermostat housing and the other on the passenger side of the engine where the heater hose pipe comes out above the water pump.

Jan 23, 2009 | 2003 Pontiac Montana

1 Answer

Throttle position sensor


Sounds like you have a vacuum leak somewhere on the engine. If the tps was bad, it would set a code and the check engine light would be on. Also, check your air tube that goes to your throttle body - make sure the hoses are connected tight and the tps is on the throttle body down on the front of your engine where the hose runs down to it. It's not really that hard to get the throttle body off. That would be the best way to change the tps - to take the whole throttle body off and put new gaskets on and tps on it. Hope this helps you out. PHil

Nov 03, 2008 | 2000 Pontiac Sunfire

2 Answers

Car is leaking antifreeze from underneath of car


I would check and replace the thermostat if it is bad, recheck the connections of the heater hoses to the heater core, and if none of these are bad, the heater core is most likely gone bad. Also, depending on where the overflow canister is, and if the radiator cap has gone bad, it might be letting too much antifreeze out of the system and overfilling the overflow canister.

Aug 07, 2008 | 1999 Mitsubishi Eclipse

1 Answer

99 taurus sho coolant leak


Honestly i would say take it to the shop something like that should not cost you to much at all then you dont have to worry about anything.... But its most likely you Heater hose

Aug 05, 2008 | 1999 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...