Question about Cars & Trucks

1 Answer

My low beams on my 2006 Madza 6 dose no come on but the high beams come on, why needs to be done to fix the problem?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,585 Answers

These lights run threw the turn signal switch. Replace it.

Posted on Dec 11, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

I have a 2006 civic SI. DRL indicator is on, driver side low and high beam ok. Passenger side low beam ok but DRL and hi beam not working. Any help is appreciated.


When either the high or low beam light is out in either side, DRL (daytime running lights) indicator will come on. When one bulb goes out, that's a clue the opposite bulb will burn out soon, so its best to replace both bulbs. If it was a fuse issue, both left and right side would be out. If driver side is OK but passenger side is not, then its a bulb issue. A 2006 Honda civic takes 9006 (HB4) low beam bulbs and 9005 (HB3) high beam bulbs. Cheapest is online from Walmart site-2-store. After procuring, wear latex, vinyl, or ANY gloves to keep your (corrosive) oil skin from coming in contact with headlight glass bulbs. Your skin oil will chemically react and cause shorter life span on glass bulbs. Instruction don't tell you this, so you handle with your hands, then need to replace bulbs 3 years later instead of 5 years (or more) in the future. With gloves on, pop the hood and look behind each headlight. Turn counter clockwise to unlock headlight bulb holders. Its a quarter to half turn to unlock bulb holder lock. Replace one bulb at a time so you don't confuse high beam from low beam. The wire has a tab you need to lift to pull out & disconnect wire connector. You might need a slim narrow-**** (NOT phillips) screwdriver to lift the tab; or use your house key. Snap the wire connector to the new bulb, then twist into headlight housing to secure bulb holders, then move on to the next bulb to repeat the procedure. Pict below, 9005 high beam is on the left, 9006 low beam is on the right. Handle by grasping the plastic base, not the glass bulbs. The raised potrusion on the bottom center is where the tab locks onto wire connector. Replace all 4 bulbs now, but in the future, its likely the low beam will wear out before the high beam. In the future, replace only the pair, not all 4. The factory installs inferior bulbs that go out sooner, hoping you'll take to dealership and they ******** you with higher parts-n-labor fees. As opposed to Walmart online site-2-store, it would cost you AT LEAST triple in parts & labor from dealership to replace all 4 headlight bulbs :-(
45d1f6ac-2983-42b9-a46c-30ef441b89e7.jpg

Nov 29, 2013 | 2006 Honda Civic

1 Answer

2006 Hyundai Tycson GL Headlight Problems


Could be a defective headlight relay, Located in the fuse block in engine compartment,

Nov 29, 2012 | Cars & Trucks

1 Answer

My 2004 madza 3i high and low beam are too low. I have to use high beam to see the road. Is anyone know how to fix it?


This is not hard to fix. Wait until it is dark enough outside to clearly see your headlight beams, then park your car on level ground 20 feet from a wall, fence, garage door, etc. Turn on your headlights (be sure your high beams are off) and open the hood. on the top of each headlight assembly you will find an adjustment screw... just turn the screw with a Phillips screwdriver until the hot spot in the center of your headlight beam hits the wall where it meets the ground.

Nov 22, 2011 | Cars & Trucks

1 Answer

Replacing low beam headlight for a Madza 6 2004


Easier than high-beams, need to find the black turn covers just on the inside of the fender, release metal clip holding bulb and unplug light, replace resecure and put plastic cover back on should be good to go

Sep 25, 2011 | 2004 Mazda 6

1 Answer

Low beams don't work, high beams do. Can you help?


CHECK FOR A BLOWN FUSE UNDER THE HOOD. THE FUSE SHOULD BE A 10 AMP. WHEN THE LOW BEAMS ARE ON THEN THE FUSE WILL TEST BAD. THANKS FOR USING FIX-YA. THERE IS A CHANCE THAT BOTH OF THE BULBS HAVE BLOWN BUT NOT LIKELY. GOOD LUCK

Sep 02, 2009 | 2006 Chevrolet Trailblazer Ext

1 Answer

2006 ford freestar high beams


there should be seperate fuses for the high beams in the under hood fuse box try checking them

Nov 05, 2008 | 2006 Ford Freestar

1 Answer

Front lights


look at the head lights assembly. find some phillips screw there. two of them .either one on top and one on the side. these are the adjusting screws.

do it at night. park the car in front of a wall about 6 feet away and adjust the lights.

tnx 4 using fixya,


drcool



Nov 05, 2008 | 2006 Chevrolet Colorado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...