Question about 2001 Kia Rio

1 Answer

How do you replace and install the 80 amp main fuse?

I know it is in the main fuse box by the battery on the end and has 2 nuts holding it down and I can't seem to get all of the original fuse out. Does it all have to come out? Without the fuse when I connect the battery back now the fan comes on direct and no fuel pump and all dash light s are on without the key in start position.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Kia Master
  • 3,368 Answers

It sounds like you need to get one of your buddies with a bit more experience to help you. If you cannot get the old one out where will you put the new?

Posted on Dec 11, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76164 Answers

SOURCE: jump wont work. 80 amp fuse blown under hood. where does fuse go

that is the alternator and vehicle power supply fuse, did u jump this wrong? u will need to replace this fuse before the car will start.

Posted on Mar 20, 2009

Molson02536
  • 3854 Answers

SOURCE: My son's 2004 Kia Optima started stalling on the

Start with the simple and replace the fuel filter. The fuel filter should be replaced every 15,000 miles or once a year to ensure the fuel system is running 100%. Auto Zone will have the fuel filter and can give you the step by step instructions to getting the job done with common tools. If it's the fuel pump failure, you have not gotten the car restarted. Good luck and keep me posted, be glad to know you got your car running 100% again soon and please rate.

Posted on Jan 11, 2010

  • 972 Answers

SOURCE: 2002 Kia Sportage will not start.

p0560 is system voltage problem. open or short between the battery positive and the ecm.CHECK ALL FUSES. dosnt matter what they are labeled under dash and under hood replace any that are bad and retry to start. no start then check voltage to ecm grounds to. i dont have a wireing diagram to give you but for a small fee or free the dealer can make you a copy.make sure all the wires that go to battery terminals are not corroded and are making good contact [verified with volt meter]. if after all checks ok then replace ecm. as a side note i havent had to change one ever.

Posted on Apr 11, 2010

Testimonial: "Thank you for the help. We will continue to check all fuses and wires."

  • 2 Answers

SOURCE: need wiring diagram for 2001 kia sportage , need it for fuel pump

2002 kia optima has no fire to the spark plugs
or spark plug connector

Posted on May 18, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i turn of the red imobaliser light. It is not on when key in the ignition only when removed


is lamp in the CLUSTER? (not on ours)
no other lights stuck on (warning?)
are you saying the IMMO lamp glows, key out of car>?
that is a relay stuck. (or bad ignition switch or short there)
what country, this is USA site, so no country and no engine stated.
means all answer are wrong. (guessing)

it has its own theft deterrent ECU. (has power all the time,)
and the Immobilizer to main PCM.
my guess is one of 2 relays bad. (or input key switch bad to relay)
IG1 relay
and ( EFI-EOD) relay. can fail if above is stuck.


25397164-unf1iprsnlx2ajznacse1210-3-0.jpg

Feb 02, 2015 | 2001 Toyota Land Cruiser

1 Answer

Instructions on changing the 100 amp battery fuse on my '01 Nissan X-Terra


These bigger fuses are sometimes bolted in. If you are looking at the fuse box under the hood, look on either side of the box. You should see little bolts to remove that will let the 100 amp come out. Oh yeah, disconnect the battery first!!!...Chris

Dec 02, 2013 | 1992 Mazda MX-3

2 Answers

How to change 80 amp fuse on 2008 Chevy Equinox


Locate the fusebox
Locate the 80amp fuse you wish to replace
Remove the old fuse
Take new fuse and insert it into slot
Test the fuse by seeing if the electronic that runs on itsit is working

Oct 13, 2013 | 2008 Chevrolet Equinox

1 Answer

Will not start there is no juice going from the battery to the engine at all the lights will not turn on or the horn won't blow nothing works at all


did you changed the battery ? and then it did not start, how do you know that it is fully charged.
well lets assume that you are right, get a test light, start by putting one end to the battery positive +, the other end touch the engine block, valve cover what ever is metal on the engine, if comes on you are ok is far is the battery, then if ok, open the fuse box next to the battery and look for a main fuse, 80 or 100 amp, if you cant see inside, or you cant pock it, pullet out, ground one leg on the body any were, and touch the other leg with the test light, if it light up is ok, if you can pocket, the test light mast light up when you hook up the test light alligator to ground. and continue testing all the big fuses, also look at the battery + terminal may have a little box on top with 1 or 2 fuses, main fuses, check them the same way, both side of the fuse must lit up, if one side does not lit up, you have a open main fuse. good luck.

Jul 29, 2012 | 1991 Honda CRX

1 Answer

I need to know what relay r fuse runs my main power


There is a 175 amp "Megafuse" located at one end of the power distribution box located under the hood. Remove the 2 nuts that hold the cables onto the box and the fuse will come off.

Apr 18, 2012 | 2005 Ford Taurus

2 Answers

Where is the 80 amp mega fuse on 2008 equinox


I use and I'd recommend you register for free at www.autozone.com Once registered you'll have access to repair and shop manuals for virtually any car or truck. All the data, specs and diagrams you need now or may need in the future will be a couple of mouse clicks away.

Oct 10, 2011 | 2007 Chevrolet Equinox LS New Cars

1 Answer

I have a '95 lumina. It died in my driveway and now I have no power to anything including the dash lights. I have replaced the alternater and battery to no avail. What could it be?


Well not being able to see and test the vehicle it leaves me a couple of guess's which you will need to check out.

So you changed the battery ,, ?? was it dead ?? and the alternator ?

check the ground connection leading of the battery terminal to the cars body ensure its connected properly, there should also be a connection to the engine.

check the positive lead wire to the fuse box.

to test this easing (connect a voltage meter a. ground to cars body, b. pos to battery terminal)

if the wiring is fine then the only other possible thing is the MAIN FUSE. this fuse is located in the fuse box and is eighter an 80 amp, 90 amp or 100 amp fuse. open the fuse box and look at where the main battery wire connects you should see the use there. its bolted in place. or simply check the diagram under the fuse box cover.

Other than that its the car battery which you said you replaced and it still didnt work. So again recap
check wiring off battery to cars body, engine and fuse box,
check main fuse.

your problem has to be 1 of the 2 of them.

Mar 20, 2011 | Chevrolet Lumina Cars & Trucks

1 Answer

Just wondering where the Camshaft position sensor in my 2005 Dodge Neon is as I need to replace it.


Removal & Installation 2.0L engine camshaft position sensor location chry_car_2.0_cpsloc.gif

2.4L engine camshaft position sensor location chry_car_2.4turbo_cpsloc.gif

2.0L SOHC Engine To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Brake booster hose and electrical connector from holders on end of cylinder head cover and reposition
    • Electrical connectors from camshaft position sensor
    • Camshaft position sensor mounting screws
    • Sensor
To Install:
  1. Install or connect the following:
    • Camshaft position sensor. Torque sensor mounting screws to 80 in. Lbs. (9 Nm)
    • Brake booster hose and electrical harness in holders on end of valve cover
    • Electrical connectors to camshaft position sensor
2.4L Turbo Engine To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Air cleaner box
    • Plastic clip for the wiring harness from the stud on the valve cover
    • Nut holding the clip for the oil supply line to the turbo and disconnect the fresh air makeup hose from the valve cover
    • Electrical connectors from camshaft position sensor
    • Camshaft position sensor mounting screws
  3. Remove sensor
To Install:
  1. Install or connect the following:
    • Camshaft position sensor torque sensor mounting screws to 80 in. lbs. (9 Nm)
    • Electrical connectors to camshaft position sensor
    • Nut holding the clip for the oil supply line to the turbo and disconnect the fresh air makeup hose to the valve cover
    • Plastic clip for the wiring harness to the stud on the valve cover
    • Air cleaner box
    • Negative battery cable
prev.gif next.gif

Aug 01, 2010 | 2005 Dodge Neon

3 Answers

Removing the 8o amp main fuse from 1986 Toyota pickup


yes, you must remove the top panel on the fuse block the 80 amp fuse is bolted to the the fuse panel, hope this helps if not get back to me as i strive to be the best please rate my fix Thanks Ray

Apr 29, 2009 | 1986 Toyota Pickup 4WD

1 Answer

Altenator is not charging the battery


sir , the altenator has 3 wires at the connector correct ? a white/red , a green/white and a black , the white/red wire is involved with a 10 amp fuse to do with the charging meter / gauge , the fuse located behind left side of dash .. the green/white wire is is involved with 2 fuses , a 10 amp ECU fuse and a 25 amp Main fuse located at left rear of engine compartment main box , and the black wire is involved with a main 80 amp fuse at the main box also . both of these 2 wires end up at the positive side of the battery , please verify all these fuses are good . if they are indeed good , then open wiring would be next step verify continuity on black and the white/green wires . i would post a link to diagram but autozone repair info site is down at this time . if ya need more help , please ask .

Jan 05, 2009 | 2002 Kia Rio

Not finding what you are looking for?
2001 Kia Rio Logo

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...