Question about Cars & Trucks

Open Question

My half gear is causing me problems in a 07 SCANIA with a GRS905 Gearbox. Have fully checked out actuator and indent balls. AlI functioning fine. When have a gear and then change half gear it ends up in no gear. I can conclude all other gears function fine including main high low.Think it's interior problem now. What I really need is full parts or assembly manual, something to let me know what's inside before I remove rear housing. Scania no real help so far as regards info I need. Can you help? My only tractor unit and under awful pressure now. I do all maintenance myself.

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emjem74
  • 162 Answers

SOURCE: speedo plug gear has broken off into gearbox

well you can but it is a bit more difficult than that as you will need allignment tool to replace and also the might be excess tension and you might need a pulling tool also to remove. it is very unusual that the mechanism drops into the gearbox though? well without effecting the performance of gearbox such as whines and creaks?

Posted on Mar 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Scania r420 opticruise 12 speed shows gearbox malfunction error. gear shifting from 6-7 gear goes automatically to a free gear.


Sorry know how to strip and repair a 12 speed foden gearbox with air change operating system ,but these new danfangled things are all electronics so you will need a computer nerd with the right software not a old seat of the pants diesel fitter like me whos now a dinasaur.Could be a computer fault but it could also be a fault with epalyptic gear train ,like a electrical solonoid operating a valve .Sorry no idea at all

Feb 22, 2016 | Cars & Trucks

2 Answers

My scania is showing gearbox malfunction on dash.what could be the problem?


Hi there I dont know to much about your type of g/box is it semi auto or a 16 /18/ speed sincro box as most times its the splitter and main cause is water in air lines.

Nov 05, 2014 | Cars & Trucks

1 Answer

In 2008 first 4th gear and later 2nd and 4th gears kept jumping out. I was told that all the bearings and other components inside the gearbox were worn out so Ihad them overhaul the gearbox. A few months...


a gear box place should know more than me but this can also be caused bye a little ball bearing and spring .... these 2 things push on the selecter shafts and fit in to a groove that holds the shaft in the right spot .. that is what u feel when u change gear and it stays in position ....... the spring - springs can looz tention .. brake or the ball can wear or the groov it sits in to can do the same making it not hold in position ... 2nd and 4th are prob on the same shaft and this problem useully happens under load or taking off quick ........ i think they call them retainer springs and ball

Jun 07, 2011 | Toyota Pickup Cars & Trucks

1 Answer

Why does my van kick when i put it in reverse?


Hi, if you have a manual gearbox then the problem could be any of the following:
1. gearbox oil could be low causing the gears to bite to hard.
2. clutch could be low and need replacing.
3. gearbox or engine mounts could be worn causing the engine or box to **** when put under pressure.
4. ball joints could need replacing such as bottom ball joint and anti roll bar bushes.

you can check the oil by finding the oil level bolt on gearbox remove bolt and if oil comes out its ok if not it needs topping up.

you can check engine/gearbox mounts by getting a good hold of the top of engine and give it a hard pull and push their should be only slight play any more and some mounts may be worn.

ball joints you can check by jacking the van off the floor then use pry bar to put bushes under pressure and check for play, their should be only slight play any more and the bush will need replacing.

Now if you have auto box then the chances are the fluid is bad and needs replacing or worse case it could be that the torque converter is on its way out.

let me know how you get on or if you need further assistance ok

Jun 27, 2010 | Cars & Trucks

2 Answers

My peugeot 307 gear linkage counter balance


i can't change into 2nd,4th and reverse gears. i think its a gear lever cable not sure doe any ideas?

Dec 27, 2009 | 2005 Peugeot 405

2 Answers

Isuzu bighorn 1994 manual, slips out of 4th and


Problem is the detent springs for 4/5 gear have gone weak .
If you are handy its take the top off the gearbox from inside the car and you will see the plug then the springs and balls .
If not its a transmission shop job.

Sep 24, 2009 | 1994 Isuzu Trooper

1 Answer

I LEFT MY CAR PARKED OVER NIGHT IN NUTRAL ADN NEXT


Alfa's have a Nylon ball with the gear selector (under the gearbox). They wear pretty easily. This could be pretty worn, either that or you're running low on gearbox, or "selespeed" oil. Check them out. They're pretty important and can cause serious problems to the gear box if not looked after.

Aug 04, 2009 | 2000 Alfa Romeo 156

1 Answer

Hi, I was trying to fill the oil in the gearbox. But I opened a wrong one nut. when I make that nut loose I hear something falling inside the gearbox. Now the gears r not working fully


this would be the detent ball i believe you might better have to to a shop to repair before that gets ground into the gears. or try draining fluid and see if you can get out. should be a spring and ball

Sep 03, 2008 | Volkswagen Golf Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...