Question about 2001 Ford Explorer Sport

1 Answer

Mechanic fixed my signal light switch with new one but now once wipers turn on I cant turn them off I was told I need a harness cause he broke the pin in side harness

Nothing really I need to know wht is the name of the part I have to purchase to get it fixed

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 22,156 Answers

Just solder the wires together ,make me proud of doing a really good bodge job ,better than i can do .....ahhaha

Posted on Dec 11, 2014

  • joann spivey
    joann spivey Dec 11, 2014

    thank u but do u know wht kind of harness i need if that dont work

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the windshield wiper fuse located in the fuse box on a 06 crown victoria


drivers side inner fender under the hood, look in the owners manual for the number and amps. some are marked under the lid itself

Mar 19, 2015 | 2006 Ford Crown Victoria

2 Answers

I have a 2007 mustang an the wipers wont turn off I had 2 pull the fuse to turn them off can u help me


The windshield wiper motor is a smart wiper motor with an integrated electronics module. The internal components of the motor are the high/low relay, washer pump relay, and the run/park relay and associated electronics.
The windshield wiper motor receives its inputs from the windshield wiper/washer switch. These signals are ground reference signals. When the switch is placed in different positions, various input signals are selected and sent through circuits to the motor. The windshield wiper motor module identifies these selected input signals and activates the motor to the selected function.!
Your probably going to need a new wiper motor ! ! ! But you should always test before replacing parts !
Visual Inspection Chart Mechanical Electrical
  • Windshield washer pump hoses
  • Windshield wiper mounting arm and pivot shaft
  • Bussed electrical center (BEC) fuse 10 (30A)
  • Smart junction box (SJB) fuse 3 (10A)
  • Circuitry
  • Windshield wiper motor
  • Windshield washer pump
  • Windshield wiper/washer switch
  • The wipers stay on continuously
  • Circuitry
  • Windshield wiper motor
  • Windshield wiper/washer switch
  • Go To Pinpoint Test C .
PINPOINT TEST C: THE WIPERS STAY ON CONTINUOUSLY s6b~tr~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use the correct probe adaptor(s) when making measurements. Failure to use the correct probe adaptor(s) may damage the connector.
Test Step Result / Action to Take C1 CHECK THE WINDSHIELD WIPER/WASHER SWITCH
  • Key in OFF position.
  • Disconnect: Windshield Wiper/Washer Switch C2137.
  • Carry out the windshield wiper/washer switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  • Does the windshield wiper/washer switch pass the component test?
Yes
GO to C2 .

No
INSTALL a new windshield wiper/washer switch. REFER to Wiper/Washer Switch in this section. C2 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR A SHORT TO GROUND
  • Disconnect: Windshield Wiper Motor C125.
  • Measure the resistance between the windshield wiper motor C125, harness side and ground as follows:

    Windshield Wiper Motor C125 Pin Circuit C125-10 56 (DB/OG) C125-11 58 (WH) C125-1 63 (RD) C125-9 61 (YE/RD)

    s6b~tr~en~file=n0011980.gif~gen~ref.gif
  • Are the resistances greater than 10,000 ohms?
Yes
GO to C3 .

No
REPAIR the circuit(s). TEST the system for normal operation. C3 CHECK FOR CORRECT WINDSHIELD WIPER MOTOR OPERATION
  • Disconnect all the windshield wiper motor connectors.
  • Check for:
    • corrosion.
    • pushed-out pins.
  • Connect all the windshield wiper motor connectors and make sure they seat correctly.
  • Operate the system and verify the concern is still present.
  • Is the concern still present?
Yes
INSTALL a new windshield wiper motor. REFER to Wiper Motor in this section. TEST the system for normal operation.

No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
You

Feb 20, 2015 | 2007 Ford Mustang Coupe

2 Answers

Where is the fuse box for the wipers


It is under the dash panel right hand side , kick panel ? Fuse F1.1 10amp . an fuse F1.113 30 amp.
Visual Inspection Chart Mechanical Electrical
  • Windshield washer hoses
  • Wiper linkage
  • Multifunction switch
  • CJB fuses:
    • 1 (10A)
    • 38 (25A)
    • 113 (30A)
  • Circuitry
  • Windshield wiper motor
  • The windshield wipers are inoperative
  • Multifunction switch.
  • Circuitry.
  • Ignition switch.
  • Windshield wiper motor.
  • Go To Pinpoint Test A .
PINPOINT TEST A: THE WINDSHIELD WIPERS ARE INOPERATIVE Test Step Result / Action to Take A1 CHECK CIRCUITS 65 (DG) AND 1002 (BK/PK) FOR VOLTAGE
  • Key in OFF position.
  • Disconnect: Windshield Wiper Motor C125.
  • Key in ON position.
  • Measure the voltage between windshield wiper C125 pin 5, circuit 65 (DG), harness side and ground; and between windshield wiper motor C125 pin 8, circuit 1002 (BK/PK), harness side and ground.
    s3j~tr~en~file=a0039065.gif~gen~ref.gif
  • Are the voltages greater than 10 volts?
Yes
GO to A2 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A2 CHECK CIRCUITS 57 (BK) AND 875 (BK/LB) FOR OPENS
  • Key in OFF position.
  • Measure the resistance between windshield wiper C125 pin 6, circuit 57 (BK), harness side and ground; and between windshield wiper motor C125 pin 3, circuit 875 (BK/LB), harness side and ground.
    s3j~tr~en~file=a0037610.gif~gen~ref.gif
  • Are the resistances less than 5 ohms?
Yes
GO to A3 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A3 CHECK THE MULTIFUNCTION SWITCH
  • Disconnect: Multifunction Switch C202a.
  • Carry out the multifunction switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  • Did the multifunction switch pass the component test?
Yes
GO to A4 .

No
INSTALL a new multifunction switch. REFER to Section 211-05 . A4 CHECK CIRCUIT 57 (BK) FOR OPEN
  • Measure the resistance between C202a pin 4, circuit 57 (BK), harness side and ground.
    s3j~tr~en~file=a0045222.gif~gen~ref.gif
  • Is the resistance less than 5 ohms?
Yes
GO to A5 .

No
REPAIR the circuit. TEST the system for normal operation. A5 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR OPENS
  • Using the following table, measure the resistance between the multifunction switch C202a harness side and the windshield wiper motor C125 harness side:

    Multifunction Switch C202a Windshield Wiper Motor C125 pin 7, circuit 56 (DB/OG) pin 10, circuit 56 (DB/OG) pin 3, circuit 58 (WH) pin 11, circuit 58 (WH) pin 5, circuit 61 (YE/RD) pin 1, circuit 61 (YE/RD) pin 1, circuit 63 (RD) pin 9, circuit 63 (RD)

    s3j~tr~en~file=a0045221.gif~gen~ref.gif
  • Is the resistance less than 5 ohms?
Yes
GO to A6 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A6 CHECK FOR CORRECT WIPER MOTOR OPERATION
  • Disconnect all wiper motor connectors.
  • Check for:
    • corrosion
    • pushed-out pins
  • Connect all wiper motor connectors and make sure they seat correctly.
  • Operate the system and verify the concern is still present.
  • Is the concern still present?
Yes
GO to A7 .

No
The system is operating correctly at this time. Concern may have been caused by a loose or corroded connector. TEST the system for normal operation. A7 CHECK THE WINDSHIELD WIPER MOTOR
  • Key in OFF position.
  • Disconnect: Windshield Wiper Motor C125.
  • Carry out the windshield wiper motor component test as described in this section.
  • Did the windshield wiper motor pass the component test?
Yes
The system is operating correctly at this time. Concern may have been caused by binding or incorrect pivot arm adjustment. REFER to Windshield Wiper Blade and Pivot Arm Adjustment in this section. TEST the system for normal operation.

No
INSTALL a new windshield wiper motor. REFER to Windshield Wiper Motor in this section. Hope this helps !

Feb 16, 2015 | 2002 Ford Expedition

1 Answer

When the key is turned wipers come on, and the right turn signal blinks fast. We think it might be a short in the wires but can't find out where. Is there something else that could be causing the


Technically, the wipers and turn signals are on two different circuits. But its possible the wires have melted together. One place to look would be in the steering col where the wiper switch and turn signal switch come together.
You could try unplugging the harness to see if the wipers still run.

Jan 18, 2013 | 1999 Dodge Stratus

1 Answer

Turn signal handle broke off and is hanging by wires


You can buy the turn signal switch at Napa or other auto parts stores. It's a combination switch. Remove the steering wheel and remove the 2 screws that hold the turn signal switch on, unplug the wires and installation is reverse of removal.

Apr 02, 2010 | 1992 Ford F150 SuperCab

1 Answer

Car would not start. Mech stated had a fuel pump


sound as a grounded B+ wire (voltage supply), sorry but need a good honest electrician, he might need to tear down electrical harness to trace, find and repair if possible grounded wires, hope is not too much damaged

Nov 17, 2009 | Chevrolet Tahoe Cars & Trucks

1 Answer

Electrical nightmare


You need to replace the combo switch. That switch controls turn signals, wipers and high beams. It is only held in by 2 screws and the hardest part is getting to the jack plugs to unplug the thing. Also if you have cruise control be very careful not to break the cruise stalk. The crusie switch mounts in the turn signal/combo switch. If you know how to use a phillips screwdriver you should be able to DIY Good luck.If this helped rate me. If you need anymore help get back to me.

Dec 24, 2008 | 1987 Mercedes-Benz Mercedes Benz 190 Class

2 Answers

Why can't I get my wipers to work


check the fuse first if not that, than replace the windshield whiper motor under plastic panel between the hinges of the hood.

Dec 08, 2008 | 1994 Lincoln Town Car

1 Answer

Changing turn signal switch on 93 oldsmobile cutlass supreme


Removing the turn signal mechanism from the steering column is easy and can be accomplished in under a half hour. First you should remove one of the battery cables as you should have no power available when removing or installing the wiring harness.then remove the front of the steering wheel.These usually just snap on or off. Remoce the steering wheel using a small puller once you have removed the nut. . Usually available for aroung $10. Now that the signal mechanism is exposed you can wemove the plastic horn ring and also the 3 screws securing the mechanism to the steering column. Leave the mechanism on the colum for now. You can however reomove the screw that holds the lights, wiper and turn signal arm and let it hang free as there is no need to replace it if everything is working. Next you have to remove the two panesl under the dash immediately under the steering column. Tracing the wiring from the turn signal to where it enters a wiring block. This block has all the wiring from the turn signal, lights , cruise control and turn signals all on different modules. You are only concerned with the module from your tirn signals. To remove this module you have to separate the block by using a small ratchet and a 7mm socket. once the the bolt holdingb the block has been completely loosened the inner block can be oulled away from the outer block. Now the module containg the turn signal harness can be removed from the inner blosk and now you are close to removing the harness but first there is a plastic sleeve that protest the wiring as it passes along the lower part of the colimn. Squeezing one end of the sleeve you can push it out until it clears the colum. it can now be opened and reomoved from the harness. Now you can reomve the mechanism from the column and ease the harness up throught the steering solumn being careful to guide it through. The last two wires on the module , a beize and green wire that ties internally to the column will need to be cut and spliced into the new harness. Using the reverse proceedure you can install the new turn signal. First time may take a hour or so . One gets better with practice. Good luck John

Dec 01, 2008 | 1993 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
Cars & Trucks Logo

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...