Question about Cars & Trucks

1 Answer

Install motor now truck wont take gas - Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 92 Answers

I'd check lines or carburetor

Posted on Dec 11, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have 1999 vw jetta engine code c 2.ol 4cyl. just did a motor swap. same year same engine. turns over but wont start gets fuel to the rail and injectors but wont fire...if i hold a rag over it starts


if donor motor was a runner
should have worked and started no issues

if fuel and spark is there
something not connected
crank angled sensor

if engine light is on has fault codes






26342882-a1nesnqyiybqlbjizw04a1uj-4-0.jpg

Nov 06, 2016 | Cars & Trucks

1 Answer

Had a fuel pump installed and now the car wont start.


Check the following:
- Fuel pump pressure.
- Polarity.
- Fuel filter.
If the problem persists keep the starter motor engaged for 8 Seconds.
- Switch the ignition OFF.
- Pull up the error codes with diagnostic computer.

Mar 03, 2014 | 1998 Mazda MPV

1 Answer

I want to install cruise control on my 2003 dodge ram 1500


I doubt that you can. The after market kits are for manual transmissions only. The additional equipment that is required is a stepping motor for the throttle and it wont work on electronic throttles, a new speedometer shaft sensor and the controls. But here is the info: http://www.thecruisecontrolstore.com/2003-2006-dodge-ram-truck-complete-rostra-cruise-control-manual-w-gas-engine/

Feb 10, 2014 | Cars & Trucks

1 Answer

Mercedes 260e wont start


There are a couple of things it may be . Sometimes when a car is run completely out of gas they become air locked.the fuel sytem needs to be bled to remove the air. Most fuel pumps are located in the gas tank and some actually use the fuel to cool the electric pump motor. Running the tank dry may have overheated the motor and burned it out in which case the fuel pump will have to be replaced. Hope this helps.

Dec 13, 2013 | Cars & Trucks

2 Answers

Van stalled and wont start when you try to start it what is wrong with it?


the fual pump could be gone. you will smel gas but its not pumping it out of the tank

Jan 30, 2012 | 1997 Dodge Caravan

1 Answer

After running out of gas in my 1996 vortec v6 4.3L it has spark and has plenty of gas going to the motor but wont start at all


If it has spark and gas...it should start ??? make sure that the gas you put in has NO water in it ??

Jun 26, 2011 | Chevrolet 1500 Cars & Trucks

2 Answers

Just installed a rebuilt 360 in a 1999 dodge truck and it starts and idles but it wont accelerate ?


if it is idling and you push on the gas and nothing happens. sounds like you did not connect the throttle cable back up. Now if it idles and you put it into drive and push on the gas and the engine revs up and you do not move then you didnt hook up the transmission up right. if this is a manual transmission you put the pressure plate on backwards.

Feb 21, 2011 | Dodge Pickup Cars & Trucks

1 Answer

Rebuilt my motor and installed itin the car but wont run


Check for Gas...Check your Timing...You say you rebuit it..was it just the top end, or the whole motor ? I asked, because there is more things to list, but i wont go into too much detail because you might have done most of them anyway..And also check your compression....Goodluck...

Mar 02, 2010 | 1994 Geo Prizm

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...