Question about 2002 Toyota RAV4

1 Answer

How can we dismantle jcb0250757 flywheel?

Removing the gear box

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 20,706 Answers

Why not tell the job , we cant guess what you are doing.nor why.

post symptoms first , if any ,then what you've done so far
pretend we are blind( are).
is removing the gear box a statement(past tense) or asking how.
or just what,?????
gear box, is this a M/T box or A/t BOX, (AUTO OR STICK)
the fsm covers all this.,
toyota sells the FSM FACTORY SERVICE Manual,why not buy it?
this book if doing serious and major work?:??? DIY !
or alldata.com, log in and read. it's all there
and not posting engine or trans in car makes all help impossible
what engine options>

generic:
M/T (wild guess)
gain access to and....
remove transmission (long long story here)
remove flywheel bolts its out.

its like 50 steps in the FSM.
the a/T has a flex plate. and is different.

Posted on Dec 20, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have put a new clutch plate,pressure plate and release bearing on peugeot 206 but the gears are not going in when I start the car


Try starting it in gear than shift with rpm dwn shift Rev rpm up by 1500 to up shif let rpm go down by 1500

Oct 28, 2016 | Peugeot Cars & Trucks

1 Answer

Starter grinding flywheel


If you had a flywheel replaced it is possible that it is not reinstalled properly. Check for engine vibration at idle . Check that the starter is in correctly. IT appears that the starter pinion is not meshing correctly with the ring gear and that is your noise . It goes after starting because the pinion disengages from the ring gear. The problem is a misalignment between the pin ion and the flywheel ring gear ( nothing at all about polished gears ). IT is all in the installation of the flywheel -starter and gear box.

Apr 02, 2014 | 2008 Subaru Impreza Wrx

1 Answer

How to install a clutch


Basic . remove drive shaft. remove rear engine mount after supporting gear box on mobile jack and engine ,with blocks under sump undo gear box bolts and if the starter motor is involved . remove the terminal from the battery first. undo the slave cylinder of the bell housing / cable if applicable. pull the gear box to the rear . remove the pressure plate bolts by going around the plate a little at a time . Lift the pressure plat away and catch the clutch plate as it falls out. Make sure that you see the way the clutch plate goes in as if you install the new one incorrectly you will be pulling the box again. check the spigot bearing / bush in the rear of the crank shaft and if faulty or worn replace it . check flywheel face and if you want a good job then have it re-machined to flat again . Follow tensioning procedures when replacing the flywheel. put the clutch plate in position and use a clutch aligning tool to ensure that it is centred. AT this point if the plate is in correctly you should be able to hold it against the flywheel and turn it freely without the hub hitting on the fly wheel bolts. fit the new pressure plate and do the bolts up in the correct manner to the tension specs. . Replace the throw out bearing on to the housing in the throw out fork. Remove the clutch aligning tool ( tap with hammer if it appears jammed ) refit the gear box and associated items in reverse order of removal.

Feb 16, 2014 | Ford Cars & Trucks

1 Answer

Flywheel removing


the simplest way to remove a flywheel is to use an impact gun. To re-tension the flywheel place a gear box bolt in a hole and use a large flat bladed screw driver in the teeth and under the bolt against the turn of the bolt. Some flywheels seem stuck on as they are positioned on a dowel so a hit on the front side will jar them loose.

Dec 29, 2013 | 2003 Ford Explorer

1 Answer

Steps to Replacing a Clutch on mitsubishi express


for the full steps then get a workshop manual as there are some details that will be missed . Basically it is Remove the battery terminal. remove the rear drive shaft ( front also if 4wd). Remove the gear lever at the tower bolts on the gear box. Drain the gear box or be prepaired for the gear oil to run out the end of the transmission when you pull the box. . Place a bottle jack under the sump at the rear of the engine . Place a trolley jack under the gear box. undo the rear transmission mount cross member Undo all the bell housing bolts. lower the jack and the trolley jack and pull the gear box back. Undo the bolts holding the pressure plate on the flywheel a bit each at a time as you go around the plate . Remove the plate and the clutch plate ( be aware that the clutch plate will only go back in one way so watch the way the clutch hub was facing. Remove and replace the bearing in the back of the crank shaft. clean up the flywheel face ( good idea for a good non shudder job is to have the flywheel re-machined ) fit the clutch plate the right way and fit the pressure plate . Use a clutch aligner tool as it will be impossible to fit the gear box with out it. Replace the clutch throw out bearing. Now re install using the reverse processes As I said a manual shows it all

Dec 14, 2013 | Cars & Trucks

1 Answer

Install clutch on 1996 f150 302 5.0


Drop the tail shaft . remove the gear lever from inside the cab. remove the housing bolts and pull gear box back out of the way. remove the clutch pressure plate by evenly undoing the pressure plate cover bolts. lift away along with the clutch plate Remember the way the clutch plate is facing as it will only go in one way. If the flywheel is badly blued or scored remove it and have it machined flat. Check and if necessary replace the bearing/bush in the end of the crank shaft. Fit new clutch plate the correct way or the flywheel bolts will hit the clutch plate and you will have to do the job again. position up the pressure plate and use a clutch aligning tool to hold the clutch plate exactly in line with the bush/bearing in the crank. tighten up the cover plate bolts evenly so as not to warp the pressure plate. Replace the clutch throw out bearing as it will be on the way out. Reposition the gear box back on to the motor making sure that the flange faces remain parallel at all times so that the splines of the input shaft do not bind on the clutch plate splines. Push the gear box all the way home and bolt up. Do not use the bolts to pull the box in as there is something wrong and you will damage something. The box will go all the way home easily if you have done everything correctly. Finish the job.

Oct 13, 2013 | Cars & Trucks

1 Answer

Remove a jimny gearbox from the vehicle


IN cases like yours it would be quicker to lift the engine gear box as an assembly. Some times if you move the box back as far as possible and then jack up the rear of the engine you may be able to slide it forward and down past the flywheel.

May 23, 2013 | Cars & Trucks

1 Answer

Clutch installation


Genewrally speaking you need to remove the gear box. UNdo the bolts holding the clutch pressure plate on the flywheel. . Do this by undoing each bolt a few turns at a time. Remove pressure plate and clutch plate. Clean flywheel face. Remove bearing at center of crankshaft and replace as it will be dry and probably rusty. Fit new clutch plate taking care to observe the correct way the plate is fitted. Normally the raised hub section faces away from the flywheel. THis can be checked by pressing the plate against the flywheel and turning it and it it hits the crank bolts you have it in the wrong way round. Fit the pressure plate over the plate and insert the bolts. Some units have 2 or 4 bolts longer than the restand this is to allow the plate to be depressed a fraction to allow the other bolts to screw in. Place a clutch aligning tool through the clutch plate and into the bearing. Evenly retension the pressure plate bolts going alternately across the cover a bit at a time . When retensioned remove the clutch aligning tool. Remove and replace the throw out bearing on the clutch release forks. Ensure that the clutch kit is all new as mixing parts will not work. Refit the gear box. Basically that is the proceedure but to be exact get the manual for your vehicle to cover any extra steps needed for that vehicle.

Mar 07, 2013 | Ford Transit Connect Cars & Trucks

1 Answer

Noisey thrust bearing


all transmisions must be removed to remove thrust bearing there is no way around it its a ring bearing around a shaft that goes thru the cluch into the flywheel!

Aug 29, 2009 | 2004 Nissan Armada

Not finding what you are looking for?
2002 Toyota RAV4 Logo

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...