Question about Jeep Cars & Trucks

1 Answer

How do I remove the turbocharger for a jeep Cherokee 2.8 L crd manual

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 20,706 Answers

Why not FIRST stated the reason.
I'm replacing it.
i'm fixing it.
I don't like it , taking up space.there.. or hate sounds it makes.
I xxxxxxxxx???????
for ever, ?????????

Posted on Dec 13, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
dennymulford
  • 1055 Answers

SOURCE: jeep cherokee CRD Limited

you can get one at auto zone,or go too ebay and order one

Posted on Mar 15, 2009

ewashmidas
  • 362 Answers

SOURCE: both the abs and brake light is on and stays on what could be wro

Your ABS systems use a combination of electronic and hydraulic systems to modulate the brakes individually to prevent them from locking up. Antilock systems consist of wheel speed sensors, a hydraulic control unit (HCU), and an electronic control unit (ECU). Because of how complex the system is your computer does a self-test. If the check is successful, the ANTILOCK and BRAKE lights will go out within a few seconds. If one of the component of the ABS system fails to pass the test one or both lights will remain lit. One or both warning lights may also come on while driving, also indicating a problem. If just the ANTILOCK warning light comes on, some ABS component has failed, but the car still has hydraulic brakes. You or a technician will have to perform further testing to pinpoint cause and the proper repair.

Please let me know if this information is helpful. Positive feedback is appreciated. Thank You!

Posted on Mar 30, 2009

  • 61 Answers

SOURCE: 2003 jeep cherokee 2.8 CRD engine sqeeking noise

It could be that you got some water on your serpentine belt and that will cause it to squeak. Try buying a can of "belt dressing" from an auto store and spray it all over your belt and see if that will stop it. It's a cheap and easy thing to try before replacing expensive parts. Hope this works for you, let me know how it goes. Goodluck!

Posted on May 05, 2009

  • 69 Answers

SOURCE: WG Jeep Grand Cherokee Limited workshop service manual.

see if advanced auto, or autozone carrys it

Posted on Feb 04, 2010

ZJLimited
  • 17970 Answers

SOURCE: jeep grand cherokee 2.7 crd

DTC P0243 - Turbo/Super Charger Wastegate Solenoid A
Description: Open or shorted condition detected in the turbocharger wastegate solenoid control circuit.


Here is the flow chart for that code (some images could need to clicking for zoom)...

P0243-WASTEGATE PRESSURE CONTROL PWM

zjlimited_337.gif

For a complete wiring diagram Refer to Section 8W.

When Monitored: When the ignition is on.
Set Condition: The ECM detects an open or short circuit in the Wastegate solenoid circuit.

Possible Causes
DAMAGED WIRING HARNESS OR CONNECTORS
WASTEGATE SOLENOID
(F504) FUSED IGNITION SWITCH OUTPUT OPEN
(K139) WASTEGATE SOLENOID DRIVER CIRCUIT OPEN
(K139) WASTEGATE SOLENOID CIRCUIT SHORTED TO GROUND
(K139) WASTEGATE SOLENOID DRIVER SHORTED TO VOLTAGE
(K139) WASTEGATE SOLENOID DRIVER CIRCUIT SHORTED TO ANOTHER CIRCUIT
ECM
INTERMITTENT CONDITION

Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING)

Diagnostic Test
1. DAMAGED WIRING HARNESS OR CONNECTORS

zjlimited_338.gif

Turn Ignition off.
Disconnect the ECM harness connectors.
Disconnect the Wastegate Solenoid harness connector.

NOTE: Check connectors - Clean/repair as necessary.


Are any wires or pins damaged?

Yes
Repair or replace any damaged wire or connectors.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).

No
Go To 2


2. WASTEGATE SOLENOID

zjlimited_339.gif

Reconnect the ECM harness connector.
Reconnect the disconnected Wastegate Solenoid harness connector.
Turn the Ignition on, engine not running.
Disconnect the Wastegate Solenoid harness connector.
Connect an incandescent test light across the supply and driver pins at the Wastegate Solenoid harness connector.

NOTE: The ECM will perform a self check of the circuit after approximately 30 seconds, which should light the incandescent test light.


Does the light illuminate brightly after 30 seconds of being connected?

Yes
Replace the Wastegate Solenoid.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).

No
Go To 3


3. (F504) FUSED IGNITION SWITCH OUTPUT OPEN

zjlimited_340.gif

Connect an test light between the Wastegate Solenoid connector Fused ignition switch output circuit and battery negative.
Compare the test light brightness to that of a direct connection to the battery.

Does the light illuminate brightly?
Yes
Go To 4

No
Repair the open (F504) Fused Ignition switch output circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).



4. (K139) WASTEGATE SOLENOID DRIVER CIRCUIT OPEN

zjlimited_341.gif

Disconnect the ECM harness connectors.
Measure the resistance of the Wastegate Solenoid driver circuit between the Wastegate Solenoid harness connector and the ECM harness connector.

Is the resistance less than 10 Ohms?
Yes
Go To 5

No
Repair the open (K139) Wastegate Solenoid control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).


5. (K139) WASTEGATE SOLENOID CIRCUIT SHORTED TO GROUND

zjlimited_343.gif

Measure the resistance of the (K139) Wastegate Solenoid driver circuit between the Wastegate Solenoid harness connector and battery negative.

Is the resistance less than 10 Ohms?
Yes
Repair the (K139) Wastegate solenoid circuit shorted to ground.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).

No
Go To 6


6. (K139) WASTEGATE SOLENOID DRIVER SHORTED TO VOLTAGE

zjlimited_344.gif

Measure the voltage between the (K139) Wastegate Solenoid driver circuit at the Wastegate Solenoid connector and battery negative.

Is the voltage less than 1 volt?
Yes
Go To 7

No
Repair the (K139) Wastegate solenoid driver shorted to voltage.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).


7. (K139) WASTEGATE SOLENOID DRIVER CIRCUIT SHORTED TO ANOTHER CIRCUIT

zjlimited_345.gif

Measure the resistance between the (K139) Wastegate Solenoid driver circuit in the ECM harness connector and all other circuits in the ECM harness connectors.

Is the resistance less than 10 Ohms?
Yes
Repair the (K139) Wastegate solenoid circuit shorted to another circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING)


No
Go To8


8. WASTEGATE SOLENOID

zjlimited_346.gif
Reconnect the ECM harness connector.
Reconnect the disconnected Wastegate Solenoid harness connector.
Turn the Ignition on, engine not running.
Disconnect the Wastegate Solenoid harness connector.
Connect an incandescent test light across the supply and driver pins at the Wastegate Solenoid harness connector.

NOTE: The ECM will perform a self check of the circuit after approximately 30 seconds, which should light the incandescent test light.


Does the light illuminate brightly after 30 seconds of being connected?
Yes
Refer to the INTERMITTENT CONDITION Symptom (Diagnostic Procedure).

No
Replace the ECM.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).

------------------------------------------------------------------------------------------------------------------------------------------------

Keep us updates.

Posted on May 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need new tail lights on crd 2008 Grand Cherokee, where can I buy them? and ship to Icelnad


did you all jeep:?
call them all and ask for international shipping.
they all have email. , all, google for Jeep dealer, click parts, click email.

Dec 16, 2013 | 2008 Jeep Grand Cherokee

1 Answer

How to program new remote for my UK jeep cherokee 2.8 crd 2004


I suggest you try one of those instant download manuals. My
brother ( a mechanic) buys when he can't fix some technical issue with the manual at www.reliable-store.com . A lot of mechanics actually do this. Website is very good for this. Must try it !!

Mar 03, 2018 | Cars & Trucks

1 Answer

What grade of transmission oil do I use for a 2003 jeep grand cherokee crd


The obvious answer to that would be to look in your Owner's Manual.
If you do not have an Owner's Manual, you can get one at:
http://www.jeep.com/en/owners/manuals/

The service manual lists two types depending on which engine your vehicle is equipped with:

4.0L Engine requires ATF Plus 3 or ATF Plus 3 Type 7176
4.7L Engine requires ATF Plus 4 or ATF Plus 4 Type 9602

Jan 08, 2012 | 2001 Jeep Cherokee

1 Answer

Loud Intermittent Buzzing Noise Jeep Cherokee Sport 2.8 CRD 2005


I would need to hear this noise to help, sorry, but you need a shop to look into this.

Feb 07, 2018 | 2001 Jeep Cherokee

1 Answer

I have a 2005 jeep cherokee 2.8 crd the key


disconnect the battery or pull the ignition fuse,then replace the ignition

Sep 21, 2009 | Jeep Cherokee Cars & Trucks

1 Answer

Can't remove the tyre to change


lift up number plate flap then remove the three bolts on under side and this will allow you to access spare tyre

May 26, 2009 | 2004 Jeep Grand Cherokee

1 Answer

Jeep cherokee CRD Limited


you can get one at auto zone,or go too ebay and order one

Mar 15, 2009 | 1998 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

79123 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...