Question about Isuzu Cars & Trucks
- Full engine Rebuilt - Crankshaft Sensor Replaced - Fresh Diesel in tank
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
You can't use a tool to pull codes from an '87 BMW 325(e). You have the 2.7 liter and your DME, or computer is a Motronic. If you had a 325i, then a tool could read the codes because the computer was upgraded that year to a Motronic 1.1 system with a round plug in under the screw cap on the driver's side under the hood. The only tool you can buy is the one for resetting the service interval light and resetting the oil change light. To answer your question about going about finding your driveability problem would be to get a BMW Bentley Manual. This manual shows you how to use a standard voltmeter to check everything from your computer plug in. Your computer is located above the glovebox.
Posted on Jun 05, 2009
SOURCE: reprogramming remote and key
if its early 05 round heart shaped remote it needs programming into system at dealer with Tech2
later 05 to 07 had square (rectangle) shaped remote
1.2 ID Code Additional Registration
Note: This procedure will add additional remotes to the Keyless Entry Control Units memory. A total of 4 remote transmitters may be programmed into the Keyless Entry Control Units memory. When a total of registered and newly registered remotes exceed 4, the oldest one shall be erased.
1 Note: Make sure that all the doors are closed and unlocked. Insert the ignition key into the ignition switch.
Open the driver's side door.
2 Turn the Ignition key to the “ON” position and then to the “LOCK” position three times
(The key should remain in the “LOCK” position)
Note: This step must be carried out within five seconds.
3 “CLOSE” and “OPEN” the driver’s doors once (Leaving the driver’s door in the “OPEN” position)
Note: This step must be carried out within five seconds after step 2 is completed.
4 Wait for 8 seconds (This wait time is critical)
5 Turn the Ignition key “ON” and then to the “LOCK” position once and turn key to the “ON” position (The key should remain in the “ON” position)
OR on/lock once
Note: This step must be carried out eight seconds after step 3 is completed.
6 “CLOSE” the driver’s door
The HAZARD lights should flash 3 times (This acknowledges the Keyless Entry Control Unit has entered programming mode)
7 Operate the lock or unlock button of the transmitters to be programmed; a flash of the HAZARD lights indicates the remote has been successfully programmed into the control unit
8 The HAZARD lights will flash approx 4 seconds after pressing the remote button to indicate the Keyless Entry Control Unit has exited programming mode.
Posted on Jun 21, 2009
SOURCE: isuzu C223 timing
need a injector pump dial indicator to set up lift in pump (movement on dial indicator)0.05mm at correct timing mark on crank pulley 12 deg.
the above is an example for 4JB1 & 4JB1-TC
which are isuzu diesel engines
Posted on Jul 27, 2009
Tips for a great answer:
Jan 22, 2016 | Isuzu Pickup Cars & Trucks
Aug 27, 2014 | Isuzu Cars & Trucks
Jul 13, 2014 | 1998 Isuzu Rodeo
Jun 30, 2014 | 1995 Isuzu Rodeo
Nov 16, 2010 | 1998 Isuzu Rodeo
Mar 08, 2010 | 2002 Isuzu Rodeo
Sep 06, 2008 | 1994 Isuzu Rodeo
Aug 18, 2008 | 1994 Isuzu Rodeo
Jul 13, 2008 | 1994 Isuzu Rodeo
Dec 16, 2017 | Isuzu Cars & Trucks
192 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: