Question about Cars & Trucks

1 Answer

How can I get interior lights on, all the sockets are working yet the lights don't work.

They are all brand new and have a slide switch to turn them on and off manually and at the other end is female adapter for plugging in (what I don't know, maybe old head phones lol) I am plugged into 110v house current, I've tried turning the motorhome on in auxiliary battery power but to no avail, what am I missing? And any idea where I can get a manual too, Thanks Carmen

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 7 Answers

My answer is going to be a fuse! Find the owners manual and in the manual locate fuse box or junction box and start looking fora blown fuse! Possibly fuse that says auxiliary!

Posted on Dec 11, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Inside lights will no go off when all doors are closed on my 1995 ford windstar


Could be the interior lamp relay , stuck contacts inside the relay ! Located in the I/P fuse panel .

Mar 12, 2017 | Ford Cars & Trucks

1 Answer

My turn signals don't work and my interior lights don't work I check fuses please help


Is the interior light switch turned all the way off? As for the signals check for 12V at the bulb. If its there you have a bad bulb, poor connection, bad socket, or poor/open ground. If no voltage at the bulb you have an open circuit or bad signal switch, you need to do more troubleshooting of the circuit to find the problem.

Feb 05, 2015 | 2000 Mazda Protege

1 Answer

Why won't my interior lights and windows don't roll up


check the fuses in the fuse panel. make sure the interior light isn`t burnt out and needs replacing. also some light switches(for the headlight) have a switch built within it that if its turned too far one way it will shut of the interior light function. if this not the problem then check for power and ground at the interior light socket as there could be damaged wire. if the fuses are good and the power windows don`t work then you will have to check the window switch for power and grounds as the other windows are feed through the drivers switch. if you have power and grounds then you may need to replace the switch. if you have no power or grounds then you will have to check for a broken wire were the wires go from the door to the body of the car as they have a problem with breaking. there is also a power window relay in the relay box.

Jun 09, 2014 | 2002 Mercury Sable

1 Answer

03 chevy venture rt.front parking light&turn light don't work replace bulb&socket


The rapid flashing occurs because of the light problem. If the 20A PARK LP fuse in the underhood fuse block is OK, the front marker lamps and the park lights should turn on when you set the headlamp switch to PARK. If the 10A T/SIG fuse in the instrument panel fuse block is OK, and the ignition switch is on, moving the turn signal multi-function switch to signal a right or left turn should cause the turn signals to flash. If this doesn't happen, check for a missing ground connection to the socket you replaced and check to be sure the replacement lamp was not forced into the socket backwards (it happens).

Sep 17, 2012 | 2003 Chevrolet Venture Passanger

1 Answer

Brake lights and turn signals not working


on gms the brakes are hot always to fuse from it to brake switch from it to turn/hazard switch if both brake and turn dont work replace turn signal switch and it is hard to do ,remove bottom steering cover then top cover you need special inverted touqix socket to remove top and regular touqix bit for bottom lower cover must be removed two screws hold switch on one on top other turn wheel and you will see at bottom on front of switch . follow wires to big plug under dash loosen bolt in center pull plug apart section for turn switch slides in remove then replace on column wires may be hooked fight loose and pull up through along top and out with wires push new down down same spot and replace every thing takes me about 1 to 1/2 hours to do some times less.

Aug 04, 2012 | GMC Cars & Trucks

1 Answer

Power door locks don't work; interior lights don't work; intermittent front wipers don't work but low and high setting do; headlights switch doesn't work; interior dome lights don't...


these trucks have a generic body control module in the left kickpanel. just remove the plastic trim from the drivers floor molding to access the module. inspect the wire for green dust or gel. if there is signs of this then you have a corrosion problem. disconnect you battery and then try cleaning the corrosion all off using contact cleaner and penetrating oil. once the corrosion is gone then reconnect everything and try to see if it works. If not then it is possible that the module is damaged. you will need a new one.

Oct 28, 2011 | 2001 Dodge Durango

1 Answer

The lighter does not work and I can not use a GPS system. Someone suggested it may be the fuse box, but I don't know which fuse it is because the fuses are not labeled and I don't have an...


Check all the fuses.
But the same fuse works a number of things such as the coutesy lights and an under hood light if equiped. If your interior and any under dash lights work then the fuse is good. You could also have a bad ground or a bad socket. Or even the GPS plug may not fit will in the cigar lighter socket well enough.

Aug 19, 2011 | 1989 Chevrolet S-10 Blazer

2 Answers

In my rear tailights, the breaklight component is not functioning. i replaced them with brand new lights. the center breaklight located in the back window is still working. Cant figure out why they wont...


Have had this problem many time's here at my shop, if center brake light come's on which you said it does, fuse and relay are good, the problem is your turn signal switch cause the brake light circuit goes through the switch, the switch is bad even though the turn signal's still work's, good luck, hope this was evrey helpful.

May 17, 2010 | 1997 Ford Contour

1 Answer

Interior Lights malfunction


trace to switch (can't remember name, but it has to do with the timing of lights) and clean contactpoints. if not replace switch>

Nov 21, 2008 | 1998 Plymouth Voyager

1 Answer

Interior light


hi have a look at the drivers door switch the contacts get dirty and don,t always make contact yates210456

Oct 19, 2008 | 2004 Volkswagen Golf

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...