Question about 2006 Nissan Sentra

Open Question

How do I remove the power outlet? - 2006 Nissan Sentra

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

05 honda accord have no power in the cigarette lighter and power outlet


Well... because there can be several things that cause this issue, you want to start with the process of elimitation. Is your car powered on when you try and use the outlet? Most veichels will not allow power to the outlets when powered off.
Observe the outlet and remove any foreign objects from the outlet, there may be a fuse or metal from a broken acessory stuck in the outlet.
Start by pluging something that works into the outlet (like a cell phone charger wit an led to indicate power) locate your veichels fuse box as per instruction of the cars manual. Remove fuse cover and locate the fuse location of the outlet in question, often labeled power or accessory. Observe the ratings of the fuse and be prepared to replace it if need be (it's good to keep common spare fuse for your veichel in your glove,trunk,ect). Remove the fuse and use a fuse tester to test the fuse or look to observe if the fuse is blown, if so replace the fuse, if the led on the charger plugged into the outlet emit's light then you have solved your problem, and if not stop work and call a mechanic or post another question. There are other things you could do but nothing that I would advise without you asking.
good luck and thanks
Questions? Just ask! Mr.Mike

Nov 17, 2015 | Honda Cars & Trucks

1 Answer

Replace power outlet on 2006 Avalon


Try some of the Toyota parts outlets on the internet. Some of them show diagrams/ drawings of the parts IE: console . From there you can probably figure it out.

Dec 02, 2014 | 2006 Toyota Avalon XL

1 Answer

Replacing water outlet housing unit on a 2000 alero 2.4l


1. Disconnect the negative battery cable. 2. Drain and recover the coolant. Refer to Draining and Filling Cooling System. 3. Remove the air cleaner assembly. 4. Disconnect the radiator hose and electrical connectors from housing. 5. Remove the heater hose from the coolant outlet housing (1). 5.1. Remove the exhaust heat shield. 5.2. Remove the nut from the exhaust manifold. 6. Remove the bolt which retains the power steering pump and set the bolt aside. 7. Remove the coolant outlet housing bolts. 8. Remove the coolant housing. 534ebc34-93ae-48c6-a1cc-13e34a9022f9.jpg 0a94091d-c74a-40d6-a020-5b4d56595221.jpg

Feb 11, 2014 | Cars & Trucks

1 Answer

The power plug inside the center console has no power at the plug. The fuse is good. Why is there no power to that plug?


Sometimes the wire on the bottom side of the outlet comes loose. Remove the out let and check the wires. If the wiring is good, check with a test light or meter and see if you have power at the outlet. If there is power there, replace the outlet, If not, check the wiring back to the fuse box

Apr 04, 2013 | Cars & Trucks

1 Answer

Thermostat on 2005 aviator location


Removal & Installation

Print


4.6L & 5.4L SOHC Engines

  1. Partially drain the engine cooling system to a level below the thermostat.
  2. Disconnect the upper radiator hose from the water outlet adapter.
  3. Remove the power steering reservoir upper mounting bracket.
  4. Remove the bolts and remove the water outlet adapter.
  5. Remove the water thermostat and the O-ring seal. Discard the O-ring seal.
  6. Installation is the reverse of the removal procedure. Tighten the water outlet adapter bolts to 18 ft. lbs. (25 Nm). Tighten the power steering reservoir upper mounting bracket as shown in the accompanying illustration.

    0996b43f80204ea2.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of the power steering reservoir upper mounting bracket and tightening specifications


    0996b43f80204ea3.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Exploded view of the water outlet adapter and tightening specifications



5.4L & 6.8L Engines

  1. Partially drain the cooling system to a level below the thermostat.
  2. Disconnect the upper radiator hose.
  3. Remove the coolant outlet connection, as follows:
    1. Remove the bolts.
    2. Remove the coolant outlet connection.

  4. Remove the (A) coolant thermostat and the (B) O-ring seal.
  5. Discard the (B) O-ring seal.

    0996b43f80204ef0.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Remove the (A) coolant thermostat and the (B) O-ring seal


To install:

NOTE Thermostat must be installed as illustrated.
  1. Use a new (A) O-ring seal to position the (B) coolant thermostat in the (C) upper intake manifold.

    0996b43f80204ef1.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Use a new (A) O-ring seal to position the (B) coolant thermostat in the (C) upper intake manifold

  2. Install the coolant outlet connection, as follows:
    1. Position the coolant outlet connection on the upper intake manifold.
    2. Install the bolts and tighten to 15-22 ft. lbs. (20-30 Nm).

  3. Connect the upper radiator hose.
  4. Fill the cooling system.

  1. Before servicing the vehicle, refer to the precautions section.
  2. Partially drain the cooling system to a level below the thermostat.
  3. Disconnect the upper radiator hose.
  4. Remove the coolant outlet connection, as follows:
    1. Remove the bolts.
    2. Remove the coolant outlet connection.

  5. Remove the (A) coolant thermostat and the (B) O-ring seal.
  6. Discard the (B) O-ring seal.

    0996b43f80204ef0.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Remove the (A) coolant thermostat and the (B) O-ring seal


To install:

NOTE Thermostat must be installed as illustrated.
  1. Use a new (A) O-ring seal to position the (B) coolant thermostat in the (C) upper intake manifold.

    0996b43f80204ef1.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Use a new (A) O-ring seal to position the (B) coolant thermostat in the (C) upper intake manifold

  2. Install the coolant outlet connection, as follows:
    1. Position the coolant outlet connection on the upper intake manifold.
    2. Install the bolts and tighten to 15-22 ft. lbs. (20-30 Nm).

  3. Connect the upper radiator hose.
  4. Fill the cooling system.


5.4L DOHC Engine

  1. Partially drain the engine cooling system to a level below the thermostat.
  2. Disconnect the upper radiator hose, the heater water inlet hose and the heated PCV inlet hose from the water outlet adapter.

    0996b43f80204ea5.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Disconnect the upper radiator hose, the heater water inlet hose and the heated PCV inlet hose from the water outlet adapter

  3. Remove the water hose connection and thermostat.
  4. Installation is the reverse of the removal procedure. Tighten the mounting bolt to 18 ft. lbs. (25 Nm).

    0996b43f80204ea4.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Exploded view of the thermostat-5.4L DOHC engine

Aug 13, 2012 | 2004 Lincoln Aviator

1 Answer

Cigarette lighter outlets have stopped working - replacing fuses g & j did not resolve problem


remove the outlet and ck the wires for power and ground if you have power and ground than the outlet itself is bad and needs to be replaced.

Feb 24, 2010 | 2002 Chevrolet Malibu

1 Answer

Fuses seem to be in tact but power outlet doesn't work. What next?


if the fuse is good, then remove the outlet and check for power and ground at the outlet. If they are both there, then you need to replace the outlet. Also sometimes the outlet won't get grounded off of the casing so it won't work, which you also need to replace the outlet. nine out of ten times you replace the outlet.

Oct 08, 2009 | 2008 Lexus Rx 330

1 Answer

Fuse for the power outlet


Wiring to the outlet, the outlet itself, or whatever device you are using. Remove the outlet, and see if there is power and ground at the plug. If both are present, you need a socket. If not find where the wire is broken.

Jul 10, 2009 | 2007 Chevrolet HHR Special Edition

1 Answer

2006 Toyota Tacoma, power outlet/cig lighter not working


I am not sure about "fusible link", But the suggeation I can give you is to open dash or where the outlet is located and check the wires in the back of outlet with a light tester.

Jun 03, 2009 | 2006 Toyota Tacoma

1 Answer

Spare 12 volt power outlet failure


First probe the center contact in the power outlet with 12V test and confirm power or not. ( check with ign on since some outlets might only have power with the key or engine on ) If no power and all other interior items operate, remove outlet and check connection. It might not have ever been connected since being built. It happens .

Mar 30, 2009 | 2000 Nissan Pathfinder

Not finding what you are looking for?
2006 Nissan Sentra Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...