Question about 1999 Daihatsu Sirion

Open Question

Daihatsu Sirion 1999 when the gear is on (N) the engine works fine when shifting to Drive the engine goes off

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76848 Answers

SOURCE: Gearbox not doing reverse and Now just revving after Gear 2

Sorry to tell you that you have a failed transmission and it will need to be rebuild or replaced.

Posted on Jun 28, 2016

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gearbox not doing reverse and Now just revving after Gear 2


Sorry to tell you that you have a failed transmission and it will need to be rebuild or replaced.

Jun 28, 2016 | 2005 Daihatsu Sirion 1.3

2 Answers

My daihattsu sirion 1300auto 2009intermittently enter in the limp mode and o/d ligt keep blinking and the car stuck in 3rd gear any suggessions?


What is he limp mode. you have not got enough fluid are u checking it warm and in park car has to be running to check tranny only, DO NOT OVERFILL IT LESS IS BETTER THAN OVER.

Sep 19, 2014 | 2009 Daihatsu Sirion 1.3

1 Answer

What dos vvt system malfunction it mean ?


Variable Valve Timing System Malfunction, and possible causes - dirty or low engine oil
- Valve timing
- Oil control valve
- Variable Valve Timing controller assembly
- Engine Control Module (ECM)

Read more: http://engine-codes.com/p1349_toyota.html#ixzz38fIMYdTd

Jul 27, 2014 | 1999 Daihatsu Sirion

1 Answer

Daihatsu sirion 1999-issue-not keeping idle,


Most times engine surging is caused by a manifold vaccuum leak. Lightly spray some carburetor cleaner around the intake manifold and vaccuum lines to check for a leak.

Oct 29, 2013 | Cars & Trucks

3 Answers

Is replacement of 2007 Daihatsu Sirion 1.3 fanbelt a relatively simple task or is it for a professional mechanic only?


DO IT YOURSELF... It IS fiddly but perfectly do-able.. easiest way to do it is to remove plastic 'dirt shield' from driver's side inner wing (next to drive shaft and brake line) obviously wheel removed, or rotated is ok.. removal of modern plastic 'tat' is simple (area of cylinder head) allowing as much finger access as possible..not much room down the side of these puppies!! Next you need to de-tension the 'serpentine' belt BUT I WOULD RECOMEND DRAWING BELT & PULLEY SET UP FIRST or taking several photos.. as a reminder of if belt goes over or under (makes sense when you see it) Use blunt engineer's screwdriver (or any blunt long driver, rod, etc) to help push and pull old and new belt about.. REMEMBER TO RE-TENSION THE TENSIONING PULLEY...BUT DONT OVER DO IT!! THE BELT WILL TIGHTEN EVEN MORE AFTER SHORT RUN IN.. ALLOW SLIGHT DEFLECTION.. 6 to 10mm should do... cleanliness is the key really, as with all engine jobs(!) Allow 2hrs to do... if you've never done before... ok?

Mar 04, 2013 | 2007 Daihatsu Sirion 1.3

1 Answer

How much engine Oil?


The engine oil capacity of a Daihatsu Sirion, 1000 cc Auto, 1999 is roughly 2.5L assuming the sump was drained and new oil filter installed.
This amount will bring the oil level on the dipstick to the upper line.
As a caution, put in 2L initially, then run the engine for a few moments then switch off. After a few minutes recheck cleaned dipstick level and top up as necessary.

Mar 16, 2010 | Daihatsu Charade Cars & Trucks

1 Answer

1999 Daihatsu Sirion


Your engine is probably an EJ-DE twin cam 12 valve.

Generally Daihatsu belts have marks on them that line up with dimples on the sprockets for the intial phasing. You rotate the engine to top dead centre on No1 piston and install the belt from there. The cams should be not be putting any pressure on the intake and exhaust valves of No1 when phased correctly.

Aug 13, 2008 | 1988 Daihatsu Charade

Not finding what you are looking for?
1999 Daihatsu Sirion Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daihatsu Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76848 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Daihatsu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...