Question about Seat Cars & Trucks

1 Answer

Remove the rear seat

Seem rear seat is first to be removed to access top mounts on shocks,plastic trim then next

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 284 Answers

What kind of car would have helped a lot. some rear seats you have a clip that you just pull the front of the rear seat up. others have a latch and others have bolts.

Posted on Jan 23, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
shanat
  • 359 Answers

SOURCE: seat belt

just pop up the plastic cover with a screwdriver

Posted on May 24, 2008

  • 29 Answers

SOURCE: replacing rear shocks

rear shocks are under the car, not inside the car.

Posted on Aug 27, 2008

johnthejag
  • 286 Answers

SOURCE: 1998 jaguar xjr rear shocks

Hi

The shockers are removed from under the car.

Good Luck !

John.

Posted on Feb 18, 2009

  • 1 Answer

SOURCE: right rear shock absorber detached from the top mounting point

Turns out that after 26 years and 233 thousand miles, the original strut gave up the ghost: Rust! I took the shock strut assembly out of a 'spare parts' Honda Accord I keep and replaced the broken one in the Honda I am now driving. Mechanically the car is still excellent, but the car is destined to dissolve around me! To remove the whole assembly required taking out one 14mm bolt at the bottom and three 12mm bolts at the top, some WD 40, several pieces of wood for leverage and a heavy mallet.. Since there is a heavy duty coil spring involved, one should take out the bottom bolt first and lift the bottom of the strut free from its position, ( this is where I used a long 2x4 and another piece of wood as the fulcrum point to pry the strut upward) Then undo the top 3 bolts and the whole unit falls out. You will also need to detach the brake fluid line that uses the strut itself as an anchor. The easiest way is to take the line off from the back of the brake drum housing ( 9mm nut) and remove the horseshoe clip and push the curved metal brake line through the small hole where the line is anchored to the strut. Use care as you will need to reattach the brake line again after installing the next shock strut. (Coil spring compression tool required) Needless to say, you will need to jack the car up and remove the rear tire first to access the whole thing.

Posted on Apr 10, 2009

town41200
  • 56 Answers

SOURCE: replacing the rear shocks. How

if i remember right under rub in the floor or hump

Posted on Nov 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove the rear seat


What type of vehicle? Most rear seats you push down and back on front edge to unlock the clip that holds seat in place, but some have bolts along front edge.

Dec 09, 2014 | Seat Cars & Trucks

2 Answers

How to remove rear struts from a Mazda CX-9?


fold rear seats forward and remove the small panel , this will reveal the top nut

Jun 17, 2014 | 2008 Mazda Cx 9

1 Answer

How do you install a driver seat plastic shield on a 2004 Ford Explorer? Its the piece of hard plastic between the door and the seat - part number 1L2Z-7862187-BAC


see if this helps
  1. Remove the rear trim screw.

snorkelbobby_44.gif
  1. Remove the lower trim screw.

snorkelbobby_45.gif
  1. Release the side trim front retaining clip.
  2. Pull the lumbar mechanism out slightly from the seat.
  3. Push down and pull out, releasing the side trim front retaining clip.
  4. CAUTION: Take care when removing the side trim cover. Excessive force will break the mounting tabs.

snorkelbobby_46.gif
Release the side trim from the mounting bracket.

snorkelbobby_47.gif
  1. Disconnect the seat control switch electrical connector.

Mar 25, 2011 | 1998 Ford Explorer

1 Answer

How to replace rear blower motor motor in 2006 chrysler town and country van


from autozone.com:


Removal & Installation

  1. Disconnect and isolate the negative battery cable.
  2. Remove the right quarter trim panel as follows:
    1. Remove first rear seat. Remove the second rear seat, if equipped.
    2. Remove the sliding door sill plate.
    3. Remove the quarter trim bolster.
    4. Remove the upper C-pillar trim and D-pillar trim panel.
    5. Remove the first and second rear seat belt anchors.
    6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
    7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
    8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.


jturcotte_39.gif
Fig. Removing the trim panel to access the rear blower motor

i. Disconnect the wiring harness connector from the accessory power outlet, if equipped.


j. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.


k. Pull first rear seat belt through the access hole.


l. Remove the quarter trim panel from the vehicle.



3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).


4. Twist the blower motor out of scroll housing.


5. Disconnect the blower motor wiring connector.


6. Remove the blower motor from vehicle.

jturcotte_40.gif
Fig. The rear blower motor is held in place by four screws
To install:

  1. Install the blower motor unit into the vehicle.
  2. Reconnect the blower motor wiring connector.
  3. Secure the blower motor into scroll housing.
  4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  5. Install the right quarter trim panel as follows:
    1. Install the quarter trim panel in position in the vehicle.
    2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
    3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
    4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
    5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
    6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
    7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
    8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
    9. Install the D-pillar trim panel and upper C-pillar trim.
    10. Install the quarter trim bolster.
    11. Install the sliding door sill plate.
    12. Install the second rear seat, if equipped, and install the first rear seat.
  6. Reconnect the negative battery cable. Check blower motor operation.

Nov 04, 2010 | Chrysler Town and Country Cars & Trucks

1 Answer

How to replace the blower motor in a dodge 2001 caravan


Removal & Installation
  1. Disconnect and isolate the negative battery cable.
  2. Remove the right quarter trim panel as follows:
    1. Remove first rear seat. Remove the second rear seat, if equipped.
    2. Remove the sliding door sill plate.
    3. Remove the quarter trim bolster.
    4. Remove the upper C-pillar trim and D-pillar trim panel.
    5. Remove the first and second rear seat belt anchors.
    6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
    7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
    8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.

      1549e60.jpg

      Fig. Removing the trim panel to access the rear blower motor

    9. Disconnect the wiring harness connector from the accessory power outlet, if equipped.
    10. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.
    11. Pull first rear seat belt through the access hole.
    12. Remove the quarter trim panel from the vehicle.
  3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  4. Twist the blower motor out of scroll housing.
  5. Disconnect the blower motor wiring connector.
  6. Remove the blower motor from vehicle.

    823bf07.jpg

    Fig. The rear blower motor is held in place by four screws


To install:
  1. Install the blower motor unit into the vehicle.
  2. Reconnect the blower motor wiring connector.
  3. Secure the blower motor into scroll housing.
  4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  5. Install the right quarter trim panel as follows:
    1. Install the quarter trim panel in position in the vehicle.
    2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
    3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
    4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
    5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
    6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
    7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
    8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
    9. Install the D-pillar trim panel and upper C-pillar trim.
    10. Install the quarter trim bolster.
    11. Install the sliding door sill plate.
    12. Install the second rear seat, if equipped, and install the first rear seat.
  6. Reconnect the negative battery cable. Check blower motor operation.

Hope helps (remember to rate this).

Nov 01, 2010 | 2000 Dodge Caravan

2 Answers

How to replace rear shocks on a 2006 cadillac srx Have 125,000 miles on car and need to replace rear shocks


Your car should have different shocks from most cars, with the magnetic, electrical charge viscosity change. Be sure that the shocks are actually not functioning correctly.

Sep 13, 2010 | 2006 Cadillac SRX

1 Answer

How replace the rear shocks on mercedes 420 sel


You will need to remove the rear seats to access the hole just above the shock. Remove the bottom seat cushion first, then find the small bolts that hold the upper seat to the frame. Once removed, you will see access to the top of the shocks (might have a plastic covering the hole).

Feb 14, 2010 | 1991 Mercedes-Benz 420

1 Answer

Do i have to remove the back seat to take rear struts off


Answer
REMOVAL - SHOCK ASSEMBLY
NOTE: Access for the nuts attaching the rear shock assembly upper mount to the vehicle is through the inside of the trunk.

Roll back carpeting on top of the rear shock tower to access shock mounting nuts.
Remove plastic cover from the top of the shock assembly.
Remove 2 nuts attaching the shock assembly upper mount/spring seat to the shock tower.
Raise vehicle on jackstands or centered on a frame contact type hoist. (Refer to LUBRICATION & MAINTENANCE/HOISTING - STANDARD PROCEDURE)
Remove the rear wheel and tire assembly from the vehicle.
Remove two fasteners holding the splash shield to the shock assembly upper mount.
Remove bolt attaching shock absorber to rear knuckle (Shock Absorber Attachment To Knuckle).
Remove the shock absorber from the rear knuckle first when removing the shock absorber from vehicle by pushing down on the rear suspension.
Move shock assembly downward and tilt top of shock outward, then remove shock assembly from vehicle through top of wheel opening

Nov 23, 2009 | 2002 Dodge Stratus

1 Answer

Are their any speical problems or tricks in replacing air adjustable rear schocks on a 2001 buick custom


Removal & Installation

  1. Remove the tire and wheel assembly.
  2. Support the control arm with a jack stand.

    0900c152802427b0.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Use support bracket tool J-23028-01 mounted on a jack to support the rear lower control arm
  3. Remove or disconnect the following:

    Electronic Ride Control (ELC) air tube from the shock Two bolts securing the shock to the control arm Trunk trim to gain access to the shock upper mounting nuts. Cover, the two nuts, and the reinforcement from the top of the shock Shock from the vehicle

    0900c152802427e1.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Remove the cover to gain access to the upper shock absorber mounting components-rear suspension


    0900c152802427e2.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the lower shock absorber mounting to the knuckle assembly-rear suspension


To install:
Install or connect the following:

Shock, reinforcement, and the two nuts. Tighten the mounting nuts to 15 ft. lbs. (20 Nm). Shock cover Trunk trim Shock-to-control arm bolts and tighten the bolts to 18 ft. lbs. (24 Nm) ELC air tube to the shock. Tire and wheel assembly

Apr 09, 2009 | 2001 Buick LeSabre

1 Answer

2004 dodge stratus SE


This is a dangerous job if you do not have the proper equipment for compressing the spring that is around the rear shock. I do not recomend performing this job without the proper equipment. Unloading the spring without it compressed can cuase injury.

If you have the proper equipment this is how you do it.

REMOVAL - SHOCK ASSEMBLY NOTE: Access for the nuts attaching the rear shock assembly upper mount to the vehicle is through the inside of the trunk.
  1. Roll back carpeting on top of the rear shock tower to access shock mounting nuts.
  2. Remove plastic cover from the top of the shock assembly.
  3. Remove 2 nuts attaching the shock assembly upper mount/spring seat to the shock tower.
  4. Raise vehicle on jackstands or centered on a frame contact type hoist.
  5. Remove the rear wheel and tire assembly from the vehicle.
  6. Remove two fasteners holding the splash shield to the shock assembly upper mount.
  7. Remove bolt attaching shock absorber to rear knuckle
  8. Remove the shock absorber from the rear knuckle first when removing the shock absorber from vehicle by pushing down on the rear suspension.
  9. Move shock assembly downward and tilt top of shock outward, then remove shock assembly from vehicle through top of wheel opening.

Aug 04, 2008 | 2004 Dodge Neon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Seat Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76673 Answers

Adam Truesdale

Level 2 Expert

284 Answers

Are you a Seat Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...