Question about Cars & Trucks

1 Answer

How do i repair service engine lite on scan code po174 1&2 banks lean

O2 sensor o2 heater sensor oxengen sensor

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 65 Answers

Most often, but not always, the "upstream" O2 sensors have died and thus cause these codes. But often enough, it is the MAF (mass air flow) sensor being dirty that causes these too. Clean the MAF, check its response rate with a scan tool that gives live data. While doing this, also check the performance of the O2 sensors. If you need some spec #s, give me the yr/mk/model of the vehicle and I will try to locate the info for you.

Posted on Dec 10, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi i have a 2002 ford ranger and it has teas codes P0446 P0135 P0141 P2195 P0403 P0171


P0446: EVAP System Vent Control Circuit http://www.autocodes.com/p0446_ford.html

P0135: O2 Sensor Heater Circuit Malfunction Bank 1 Sensor 1
P0135 Ford O2 Sensor Heater Circuit Malfunction Bank 1 Sensor 1

P0141: O2 Heater Circuit Bank 1 Sensor 2
P0141 Ford O2 Heater Circuit Bank 1 Sensor 2

P2195: Oxygen Sensor Signal Biased/Stuck Lean - Bank 1 Sensor 1
http://www.autocodes.com/p2195_ford.html

P0403:Exhaust Gas Recirculation Control Circuit http://www.autocodes.com/p0403_ford.html

P0171: Fuel Injection System Too Lean Bank 1 http://www.autocodes.com/p0171_ford.html

Nov 15, 2016 | 2002 Ford Ranger

2 Answers

What does code p1131 mean on a 2001 ford taurus


P1131 Ford
P1131 Ford - Lack of Upstream Heated Oxygen Sensor Switch Sensor Indicates Lean Bank 1

Repair Importance Level: 3/3

Repair Difficulty Level: 2/3

http://engine-codes.com/p1131_ford.html

Forum Code

Possible causes

- Faulty Oxygen Sensor

- Vacuum leak affecting bank 1 only

- Fuel injector problem bank 1

- Check for cylinder misfire on bank 1

- Engine mechanical condition

Tech notes

Though the Oxygen (O2) sensor, the Engine Control Module (ECM) has detected a lean system, which means that there is either not enough fuel or and excessive amount of air in the system. Start by checking for vacuum leaks.

When is the code detected?

The Engine Control Module (ECM) detected bank 1 oxygen (O2) at its lean limit

Possible symptoms

- Engine Light ON (or Service Engine Soon Warning Light)

P1131 Ford Description

A Heated Exhaust Oxygen (HO2S) sensor indicating rich at the end of a test is trying to correct for an over-lean condition. The test fails when the fuel control system no longer detects switching for a calibrated amount of time.

Read more: http://engine-codes.com/p1131_ford.html#ixzz3izk89wMu

Aug 16, 2015 | Ford Cars & Trucks

1 Answer

The check engine comes on but I dont lose power the code it is showing is sid 152.does anyone know what it is.


some codes dont cause power loss or may not even notice anything wrong but a check engine light a p0152 code means following answer courtesy of OBD-CODES.com === P0152 O2 Sensor (High Voltage) OBD-II Trouble Code Technical Description Article by Dale Dale Toalston ASE Certified Technician 02 Sensor Circuit High Voltage (Bank 2 Sensor 1) What does that mean? The o2 (oxygen) sensors basically measure oxygen content in the exhaust. The PCM (powertrain control module) then uses this information to regulate fuel injector pulse. The o2 sensors are very important to proper operation of the engine. Problems with them can cause the PCM to add or take away too much fuel based on the faulty o2 sensor voltage. A P0152 code refers to the Bank 2, sensor 1, o2 sensor. (Bank 1 would contain cylinder 1 and bank 2 is the opposite bank. Bank 2 doesn't necessarily contain cylinder 2.) "Bank 2" refers to the side of the exhaust that DOES NOT contain cylinder number 1 and "Sensor 1" indicates that it is the pre-cat sensor, or forward(first) sensor on that bank. It is a four wire sensor. The PCM supplies a ground circuit and a reference voltage of about .5 volts on another circuit. Also for the o2 heater there is a battery voltage supply wire and another ground circuit for that. The o2 sensor heater allows the o2 sensor to warm up faster, thus achieving closed loop in less time than it would normally take for the exhaust to warm the sensor up to operating temperature. The O2 sensor varies the supplied reference voltage based on oxygen content in the exhaust. It is capable of varying from .1 to .9 volts, .1 indicating lean exhaust and .9 indicating rich exhaust. NOTE: A condensed explanation of fuel trims: If the o2 sensor indicates that the oxygen voltage reading is .9 volts or high, the PCM interprets this as a rich condition in the exhaust and as a result decreases the amount of fuel entering the engine by shortening injector "on time". The STFT (short term fuel trims) would reflect this change. The opposite would occur when the PCM sees a lean condition. The PCM would add fuel which would be indicated by a single digit positive STFT reading. On a normal engine the front o2 sensors switch rapidly back and forth two or three times per second and the STFT would shift positive and negative single digits to add and remove fuel to compensate at a similar rate. This little "dance" goes on to keep the air/fuel ratio at it's optimal level. Short term fuel trims or STFT reflect immediate changes in fuel injector "on-time" while long term fuel trims or LTFT reflect changes in fuel over a longer period of time. If your STFT or LTFT readings are in the positive double digits (ten or above), this indicates the fuel system has been adding an abnormal amount of fuel than is necessary to keep the proper air/fuel ratio. It may be overcompentsating for a vacuum leak or a stuck lean o2 sensor, etc. The opposite would be true if the fuel trim readings are in the negative double digits. It would indicate that the fuel system has been taking away excessive amounts of fuel, perhaps to compensate for leaking injectors or a stuck rich o2 sensor, etc. So when experiencing o2 related issues, reading your fuel trims can indicate what the PCM has been doing over the long term and short term with regard to fuel. This code indicates that the o2 sensor was stuck too high or in the rich position. The PCM monitors this voltage and if it determines that the voltage is too high out of range for too long, P0152 may set. Symptoms Symptoms may include: MIL (Malfunction Indicator Lamp) illumination Engine may run very rough Engine may be running lean or rich depending on if the o2 sensor is reading correctly or incorrectly Lack of power Increased fuel consumption Causes Potential causes of an P0152 code include: Bad bank 2, 1 o2 sensor incorrectly reading rich condition Engine running rich and o2 sensor Correctly reading rich condition Signal shorted to voltage in harness Wiring harness damage/melted due to contact with exhaust components Vacuum leak (make have lean codes (P0171, P0174) present with it) Leaking injectors Bad fuel pressure regulator Bad PCM Possible Solutions If you have any lean or rich codes associated with this code, focus on fixing these first because these can cause the o2 sensor voltage readings to appear to be faulty when they are in fact only reading correctly. So, with the engine running at operating temperature, use a scan tool to observe the Bank 2,1 o2 sensor voltage reading. Is it high? If so, look at the long term and short term fuel trim readings. The fuel trims are affected by the o2 sensors as noted above. If the LTFT reading for that bank is indicating negative double digits (PCM trying to take away fuel to compensate for problem) try inducing a vacuum leak to see if the sensor voltage then goes lean and the fuel trims increase. If the o2 sensor responds, suspect a problem with the engine, not the sensor. There may be other engine codes to help you. If the o2 sensor reading remains high (0.9 volts or above) and won't respond then shut off engine. With KOEO (Key on engine off) disconnect the o2 sensor and look for signs of corrosion or water intrustion. Repair as necessary. The voltage reading should now be about 0.5 volts. If so, replace the o2 sensor, it's shorted internally. If after unplugging the o2 sensor the voltage reading on the scan tool doesn't change, then suspect wiring problems. Inspect the harness and look for any melted wires or anywhere that the o2 sensor harness is making contact with the exhaust components. If you are unsure, you can check for continuity of all four wires between the sensor and the PCM with an ohmmeter. Any resistance at all indicates a problem. Repair as necessary.

Read more at: http://www.obd-codes.com/p0152
Copyright © OBD-Codes.com

Jul 28, 2015 | Cars & Trucks

2 Answers

2000 navigator system too lean


Too Lean on which Bank of the Motor?

To have a lean O2 Code --you could have a rich fuel
condition & the pcm drove the fuel trim lean

Next you could have a vacuum leak-in the intake or exhaust system

Third you could have a failed O2 Sensor

Front or Upstream Oxygen Sensors get replaced at 100,000 miles

The front sensors are on the exhaust pipe between the motor &
the converter.

Will need a long handled flex head O2 Sensor Wrench

Mar 17, 2014 | 2000 Lincoln LS

1 Answer

What do i have to change if codes po1151 and po155 come up on my 1999 lincoln town car?


P0155 - 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 1)
This code refers to the front oxygen sensor on Bank 2. The heated circuit in the oxygen sensor decreases time needed to enter closed loop. As the O2 heater reaches operating temperature, the oxygen sensor responds by switching according to oxygen content of the exhaust surrounding it. The ECM tracks how long it takes for the oxygen sensor to begin switching. It the ECM determines (based on coolant temp) that too much time elapsed before the oxygen sensor began operating properly, it will set P0155. See also: P0135 (Bank 1).

Potential Symptoms: You will likely notice poor fuel economy the illumination of the MIL.

Causes: A code P0155 may mean that one or more of the following has happened:
O2 Heater element resistance is high
Internal short or open in the heater element
O2 heater circuit wiring high resistance
open or short to ground in the wiring harness

Possible Solutions:
Repair short or open or high resistance in wiring harness or harness connectors
Replace oxygen sensor (cannot repair open or short that occurs internally to sensor)



P0156 - 02 Sensor Circuit Malfunction (Bank 2 Sensor 2)
The o2 (oxygen) sensors measure oxygen content in the exhaust. The PCM (powertrain control module) then uses this information to regulate fuel injector pulse. The o2 sensors are very important for the proper operation of the engine. Innacurate or faulty o2 sensors can cause the PCM to add or take away fuel based on the faulty o2 sensor voltage which can cause a host of problems.

A P0156 code refers to the Bank 2,2 o2 sensor or the downstream (post-cat) o2 sensor on Bank 2. It is a four wire sensor. The PCM supplies a ground circuit and a reference voltage circuit of about 0.5 volts. Also for the o2 sensor heater element there is a battery voltage supply wire and another ground circuit for that. The o2 sensor heater allows the o2 sensor to warm up faster, thus achieving closed loop in less time than it would normally take for the exhaust to warm the sensor up to operating temperature. The O2 sensor varies the supplied reference voltage based on oxygen content in the exhaust. It is capable of varying from about 0.1 to 0.9 volts, 0.1 V indicating lean exhaust and 0.9 V indicating rich exhaust. This P0156 code indicates that the Bank 2, 2 o2 sensor is stuck low for too long or isn\'t active at all.

Symptoms: Often post-cat o2 sensor problems present few symptoms since they are inputs to the PCM to monitor catalytic converter quality and don\'t directly control fuel. sometimes no symptoms are noticeable. However the following may be possible on some vehicles:
MIL (Malfunction Indicator Lamp) illumination
Decrease in MPG
Increase in tailpipe emissions

Causes: Potential causes of an P0156 code include:
Bad O2 sensor
Signal shorted to voltage
Wiring problems due to contact with exhaust components
Holes in exhaust near o2 sensor

Possible Solutions:
If you have access to a scan tool, check the signal voltage for the Bank 2,2 oxygen sensor with the engine at normal operating temperature. Is it stuck low currently? If so, increase RPM for a few seconds and see if it affects the reading. If it begins working with increased RPM, check for holes in the exhaust near the o2 sensor that may cause a false lean. If the exhaust pipe is intact, the sensor is sluggish, replace it.

If the Bank 2,2 o2 sensor voltage reading remains low with increased RPM, unplug it and then observe the reading. It should have increased to about 0.5 volts or thereabouts. If it did, check for water intrusion or other connector problems. If none are found, replace the shorted o2 sensor. If the voltage reading is still stuck low after unplugging the sensor, then suspect a wiring problem. Using a voltmeter, with the o2 sensor unplugged, check for voltage on the signal circuit at the o2 sensor connector(PCM side). It can vary with model, but should be about 0.5 volts and not above 1 volt. If the voltage reading is too high, repair short to voltage on signal circuit. If the signal voltage checks out, suspect the PCM.


Hope this helps (remember to rate this answer).

Jun 06, 2011 | Lincoln Town Car Cars & Trucks

1 Answer

Ù?دÙ? Ù?Ø´Ù?Ù?Ø© فÙ? سÙ?ارتÙ? اÙ?تÙ?ا


Generic OBD II Diagnostic Trouble Codes

DTC CODES P0200 to P0299

P0200....Injector Circuit

P0201....Injector Circuit - Cylinder 1

P0202....Injector Circuit - Cylinder 2

P0203....Injector Circuit - Cylinder 3

P0204....Injector Circuit - Cylinder 4

P0205....Injector Circuit - Cylinder 5

P0206....Injector Circuit - Cylinder 6

P0207....Injector Circuit - Cylinder 7

P0208....Injector Circuit - Cylinder 8

P0209....Injector Circuit - Cylinder 9

P0210....Injector Circuit - Cylinder 1

P0211....Injector Circuit - Cylinder 11

P0212....Injector Circuit - Cylinder 12

P0213....Cold Start Injector 1

P0214....Cold Start Injector 2

P0215....Engine Shutoff Solenoid

P0216....Injector/Injection Timing Control Circuit

P0217....Engine Coolant Over Temperature Condition

P0218....Transmission Fluid Over Temperature Condition

P0219....Engine Over Speed Condition

P0220....Throttle/Pedal Position Sensor/Switch 'B' Circuit


P0157....O2 Sensor Circuit Low Voltage (Bank 2 Sensor 2)

P0158....O2 Sensor Circuit High Voltage (Bank 2 Sensor 2)

P0159....O2 Sensor Circuit Slow Response (Bank 2 Sensor 2)

P0160....O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 2)

P0161....O2 Sensor Heater Circuit (Bank 2 Sensor 2)

P0162....O2 Sensor Circuit Malfunction (Bank 2 Sensor 3)

P0163....O2 Sensor Circuit Low Voltage (Bank 2 Sensor 3)

P0164....O2 Sensor Circuit High Voltage (Bank 2 Sensor 3)

P0165....O2 Sensor Circuit Slow Response (Bank 2 Sensor 3)

P0166....O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 3)

P0167....O2 Sensor Heater Circuit (Bank 2 Sensor 3)

P0168....Fuel Temperature Too High

P0169....Incorrect Fuel Composition


P0170....Fuel Trim (Bank 1)

P0171....System too Lean (Bank 1)

P0172....System too Rich (Bank 1)

P0173....Fuel Trim Malfunction (Bank 2)

P0174....System too Lean (Bank 2)

P0175....System too Rich (Bank 2)

P0176....Fuel Composition Sensor Circuit

P0177....Fuel Composition Sensor Circuit Range/Performance

Nov 29, 2010 | 2005 Nissan Altima

1 Answer

Hur byter jag växellädsolja på


160....O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 2)

P0161....O2 Sensor Heater Circuit (Bank 2 Sensor 2)

P0162....O2 Sensor Circuit Malfunction (Bank 2 Sensor 3)

P0163....O2 Sensor Circuit Low Voltage (Bank 2 Sensor 3)

P0164....O2 Sensor Circuit High Voltage (Bank 2 Sensor 3)

P0165....O2 Sensor Circuit Slow Response (Bank 2 Sensor 3)

P0166....O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 3)

P0167....O2 Sensor Heater Circuit (Bank 2 Sensor 3)

P0168....Fuel Temperature Too High

P0169....Incorrect Fuel Composition

P0170....Fuel Trim (Bank 1)

P0171....System too Lean (Bank 1)

P0172....System too Rich (Bank 1)

P0173....Fuel Trim Malfunction (Bank 2)

P0174....System too Lean (Bank 2)

P0175....System too Rich (Bank 2)

P0176....Fuel Composition Sensor Circuit

P0177....Fuel Composition Sensor Circuit Range/Performance

P0178....Fuel Composition Sensor Circuit Low Input

P0179....Fuel Composition Sensor Circuit High Input

P0180....Fuel Temperature Sensor A Circuit

P0181....Fuel Temperature Sensor A Circuit Range/Performance

P0182....Fuel Temperature Sensor A Circuit Low Input

P0183....Fuel Temperature Sensor A Circuit High Input

P0184....Fuel Temperature Sensor A Circuit Intermittent

P0185....Fuel Temperature Sensor B Circuit

P0186....Fuel Temperature Sensor B Circuit Range/Performance

P0187....Fuel Temperature Sensor B Circuit Low Input

P0188....Fuel Temperature Sensor B Circuit High Input

P0189....Fuel Temperature Sensor B Circuit Intermittent

P0190....Fuel Rail Pressure Sensor Circuit

P0191....Fuel Rail Pressure Sensor Circuit Range/Performance

P0192....Fuel Rail Pressure Sensor Circuit Low In put

P0193....Fuel Rail Pressure Sensor Circuit High Input

P0194....Fuel Rail Pressure Sensor Circuit Intermittent

P0195....Engine Oil Temperature Sensor

P0196....Engine Oil Temperature Sensor Range/Performance

Nov 20, 2010 | 2004 Volvo S80

1 Answer

2006 hundai elantra P2270 code. If this is an O2 sensor, which one?


Possible O2 sensors:

P2270 O2 Sensor Signal Stuck Lean Bank 1 Sensor 2
P2271 O2 Sensor Signal Stuck Rich Bank 1 Sensor 2
P2272 O2 Sensor Signal Stuck Lean Bank 2 Sensor 2
P2273 O2 Sensor Signal Stuck Rich Bank 2 Sensor 2
P2274 O2 Sensor Signal Stuck Lean Bank 1 Sensor 3
P2275 O2 Sensor Signal Stuck Rich Bank 1 Sensor 3
P2276 O2 Sensor Signal Stuck Lean Bank 2 Sensor 3
P2277 O2 Sensor Signal Stuck Rich Bank 2 Sensor 3
P2278 O2 Sensor Signals Swapped Bank 1 Sensor 3 / Bank 2 Sensor 3
---
This is Bank 1 (closer to the dash panel) Sensor 2 (located after the catalytic converter).

---
Note: A malfunctioning front oxygen sensor may cause fuel trim codes to set.
  1. Several Diagnostic Trouble Codes use specific terminology to refer to sensor location. The illustration and key below explain the following terms:
  2. Engine BANK Bank 1 is closer to the dash panel, (also referred to as RH or right hand). Bank 2 is closer to the radiator, (also referred to as LH or left hand).
  3. UP Refers to Sensor 1 or "front sensor". It is located closer to the exhaust manifold and before the catalytic converter.
  4. DOWN Refers to Sensor 2 or "rear sensor." It is located after the catalytic converter.
  5. The following examples show how to interpret oxygen sensor terminology:
  6. B1/S1 = Bank 1/Sensor 1 = Dash panel side, BEFORE the catalyst or "upstream"
  7. B2/S2 = Bank 2/Sensor 2 = Radiator side, AFTER the catalyst or "downstream"

Aug 06, 2010 | Hyundai Elantra Cars & Trucks

2 Answers

I have a 2003 3.0 engine Honda Accord that is giving me trouble codes P2197 P0154 P2254, what do these mean? Thank you.


Here it goes.
P2197 - Front Air Fuel Sensor (O2 sensor) Bank 2 - Sensor 1 Signal stuck lean.

P0154 - Front Air Fuel Sensor (O2 Sensor) Bank 2 - Sensor 1 Heater System Malfunction.

P2254 - Front AIr Fuel Sensor (O2 Sensor) VS Line high voltage.

IF Trouble codes P0134 or P0154 are present diagnose them before code P2254.

The first thing I would do would be check the heater circuit. You will have ground, and 12V+ to the 02 sensor heater line on a cold start. This heats up the oxygen quicker and allows it to operate in the correct amount of time. 9/10 times if there is a heater circuit code it is the oxygen sensor. But 1/10 times it is a blown fuse. So checking the voltage at the sensor is a quick test for P0154.

I would backprobe the signal line when the vehicle is at a full operating temp with a graphing meter (if avail) or use a DVOM. You should see it switch between .1 volts to 1V. It should not continuously move up and down. This indicates the computer is in good fuel control.

Diaginosis the heater circuit first is best because code P2197 can be set from anything that can cause that motor to run lean. (Plugged fuel filter, low fuel pressure/volume, vacume leak).

Hope this gives you a solid path to go on & good luck.

Nov 16, 2009 | 2003 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...