Question about 2004 GMC Yukon

1 Answer

I purchased new tires and wheels for my 2004 GMC Yukon, I'm able to get it in learn mode for the tpm sensors. Upon letting air out its like its not picking up the tpm sensor. Being they

I've tried the learn steps for the tpm sensors, the horn will beep twice but it won't beep when air is left out of the left front tire. Seems like it doesn't recognize the sensors.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • GMC Master
  • 461 Answers

The programming works both ways . It will work also when you put air in.. Sometimes it takes an extra second or two to respond. Once the horn beeps twice the sequence is finished. You must repeat it again ..remember ...driverside front, passenger side front, passenger side rear...driverside rear. All within 3 to 4 minutes.

Posted on Dec 10, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I purchased a 2004 GMC Yukon Feb 7th, and the "service tire monitor" light on the DIC has always been on. What is the problem with it and can it be fixed?


This light comes on when tire pressure is low. Each wheel has individual sensors to monitor tire pressure. You have an issue with one or more of the wheels/sensors. Take it to a reputable repair shop and have the system tested. You may have one or more bad sensors or the vehicle may not have any sensors equipped if the original rims are not installed when you purchased it..

May 15, 2015 | GMC Cars & Trucks

1 Answer

Programing tpms sensor 08 silverado


Hope this helps you.

LEARN MODE CANCELLATION
The TPM system will cancel the learn mode if more then 2 minutes have passed and no sensors have been learned, or if the system has been in learn mode for more than 5 minutes. If the learn mode is canceled before any sensor has been learned, the PDM will remember all current sensor IDs and their locations.

CAUTION: Before proceeding with the steps below, ensure that no other sensor learn procedure is being performed simultaneously, or that tire pressures are not being adjusted on a TPM equipped vehicle within close proximity.

STEP BY STEP:
  1. Turn "ON" the ignition, with the engine OFF.
  2. Apply the parking brake. IMPORTANT: If the learn mode cannot be enabled, ensure the TPM system is enabled in the PDM.
  3. Turn the exterior lamp switch from "OFF" to parking lamps 4 times within 4 seconds. A horn chirp will sound and the low tire pressure light will begin to flash indicating the learn mode has been enabled.
    CAUTION: Over inflating tires may cause personal injury or damage to the tires and wheels. When increasing tire pressure do not exceed the maximum inflation pressure as noted on the tire sidewall.
    IMPORTANT: If a horn chirp does not sound after 35 seconds for any of the 4 sensors, turn the ignition "OFF" to exit the learn mode and repeat the procedure from step 1.
  4. Starting with the left front tire, increase or decrease the pressure for 8-10 seconds, or until a horn chirp sounds. The horn chirp may occur before the 8-10 second pressure increase/decrease time period has been reached, or up to 30 seconds after the 8-10 second pressure increase/decrease time period has been reached.
  5. After the horn chirp has sounded, proceed as in step 4 for the next 3 sensors in the following order:

    Right front
    Right rear
    Left rear
  6. After all sensors have been learned, exit the learn mode by turning "OFF" the ignition.
  7. After the learn mode has been exited, adjust all tire pressures to the recommended psi
  8. After adjusting all tire pressures to the recommended psi, run the tire pressure check in the DIC to see that the correct pressure is listed.

Oct 31, 2012 | Cars & Trucks

2 Answers

A message on my dash came on say serv TPM...any idea what this is?


Tire pressure monitor. First check all tires for proper inflation. If 1 or more is low fill to proper psi. If all are correct need to plug into tire pressure monitor scanner & it will tell you where the problem lies. Most likely 1 of the sensors (valve stems) is faulty & needs to be replaced. Most any tire store will have the proper scanner needed.

Aug 28, 2010 | 2007 Chevrolet Colorado (Extended Cab) New...

1 Answer

How do you reset the tire pressure monitor on 2006 yukon.


with proper air pressure in all tires will auto reset also to much air sets off sensor

Nov 04, 2009 | 2004 GMC Yukon

2 Answers

How do you clear a low tire pressure warning on a 2004 yukon


Have you driven the vehicle over 45 mph.? If not, drive 5 miles above 45mph and the light will reset.
You can also clear clear pressure reading by reseting through the DIC, mode and set buttons.
Owners manual will explain use of the DIC ( Driver Information Center)
Good luck, let me know.
Regards,

Apr 18, 2009 | 2004 GMC Yukon

1 Answer

Gmc sierra 2008 low tire pressure problem


You can follow this to reset it.
Ignition ON, initiate the TPM Learn Mode
using one of the following procedures:

  1. On vehicles equipped with keyless entry, simultaneously press the keyless entry transmitters lock and unlock buttons until a double horn chirp sounds indicating the Learn Mode has been enabled. The left front turn signal will also be illuminated.
  2. On vehicles not equipped with keyless entry, press and release the driver information center (DIC) INFO button until the TIRE LEARN message appears on the DIC display. Press and hold the SET/RESET button until a double horn chirp sounds indicating the Learn Mode has been enabled. The left front turn signal will also be illuminated.
  3. Increase/decrease the tire pressure for 8-10 seconds then wait for a horn chirp. The horn chirp may occur before or up to 30 seconds after the 8-10 second pressure increase/decrease time period has been reached. Once the horn chirp has sounded, the sensor information is learned and the turn signal in the next location to be learned will illuminate.
    After the horn chirp has sounded and the right front turn signal is illuminated, repeat step 2 for the remaining 3 sensors in the following order:
    3.1. Right front

    3.2. Right rear

    3.3. Left rear

    When the left rear sensor has been learned and a double horn chirp has sounded, the learn process is complete and the RCDLR exits the learn mode.
    Ignition OFF, adjust all tires to the recommended pressures

Jan 22, 2009 | 2000 GMC New Sierra 1500

4 Answers

2003 Cadillac seville sts TPMS reset


From 2005 STS Owners manual:
Each TPM sensor has a unique identification code. Any
time you replace one or more of the TPM sensors,
the identification codes will need to be matched to the
new tire/wheel position. Each tire/wheel position is
matched, to a sensor, by increasing or decreasing the
tire’s air pressure. The sensors are matched, to the
tire/wheel positions, in the following order: left front (LF),
right front (RF), right rear (RR), and left rear (LR).
You will have one minute to match the first tire/wheel
position, and five minutes overall, to match all four
tire/wheel positions. If it takes longer than one minute,
to match the first tire and wheel, or more than five
minutes to match all four tire/wheel positions the
matching process stops and you will need to start over.
The TPM matching process is outlined below:
1. Set the parking brake.
2. Press the push-button ignition switch to OFF/ACC.
3. Using the Keyless Access transmitter, lock and
unlock the vehicle’s doors.
4. Press the lock and unlock buttons, at the same
time, on the Keyless Access transmitter. A single
horn chirp will sound, indicating that the TPM
system is ready, and the sensor matching process
can begin.
5. Start with the left (driver’s side) front tire.
6. Remove the valve cap from the valve stem.
Activate the TPM sensor by increasing or
decreasing the tire’s air pressure for five seconds,
or until a horn chirp sounds. The horn chirp,
which may take up to 30 seconds, confirms that the
sensor identification code has been matched to
this tire position. To decrease the tire’s air-pressure
use the pointy end of the valve cap, a pencil-style
air pressure gage or a key.
7. Proceed to the right (passenger’s side) front tire,
and repeat the procedure in Step 6.
8. Proceed to the right (passenger’s side) rear tire,
and repeat the procedure in Step 6.
9. Proceed to the left (driver’s side) rear tire, and
repeat the procedure in Step 6.
10. After hearing the confirming double horn chirp, for
the left rear tire, exit the matching process by
turning the ignition switch to OFF/ACC.
11. Set all four tires to the recommended air
pressure level as indicated on the tire and loading
information label.
12. Put the valve caps back on the valve stems.

Oct 28, 2008 | 2003 Cadillac Seville

1 Answer

06 dts tire monitor reset button?


Programming TPM Sensors
1. Turn the ignition to ON.
2. Press the key fob lock and unlock buttons simultaneously for several seconds. The horn will chirp when the TPM
programming mode is activated. Important: If the TPM programming mode cannot be entered, check if the DIM is
configured with the correct RPO codes.
3. Starting with the Left Front Tire
4. Install the J 41760 over the left front valve stem. Magnets from Radio Shack, P/N 64-1888 (at $2.99), will also work.
They're too small to go over the valve stem cap, but once you remove it they slip over the valve stem just fine
instead of the GM tool.
5. The horn will sound, indicating the Left Front TPM sensor is programmed. Important: If the horn does not sound after
15 seconds, remove then reinstall the TPM sensor programming tool or place the magnet alongside the valve stem.
6. When the horn sounds, proceed to program the next TPM sensor in the following order:
o Right Front Tire
o Right Rear Tire
o Left Rear Tire
7. After the Left Rear sensor is programmed, the horn will sound twice to indicate programming is complete.
Programming Cancellation
1. The programming mode will be canceled if any of the following conditions are met:
o The ignition is turned OFF.
o All four sensors have been programmed.
o The TPM system has been in the program mode for longer than 5 minutes and no sensors have been learned.
2. If more then one minute has passed before the next sensor is programmed, all previously stored codes are
erased from the receiver's memory.
after driving around for a few blocks, if the pressure does not match the tire pressure for each wheel, then the sensor is bad.

Oct 15, 2008 | 2006 Cadillac DTS

Not finding what you are looking for?
2004 GMC Yukon Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...