Question about 1979 Ford Bronco

1 Answer

I have a 1979 bronco with a 351w engine im tyring to hook up my choke to the washer motor i ran a 14 g wire from the one that came out of the firewall to the choke and blew the fuse and found that the fuse should be 20 and the one that blew was 15 what do i need to do to get 12 v at the choke and why did they put a smaller fuse in?????

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 1,249 Answers

I would wire up a relay between the battery and the choke solenoid. Fuse the choke separately in the engine compartment. You could run the relay coil off the same washer wire as before, but this way the washer fuse wouldn't have to source current to the choke. i have a 1979 bronco with a 351w engine im tyring  - 25315115-wng3opgl1pug32fsc4t4fc4i-3-0.jpg

Posted on Dec 09, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1979 firebird esprit wiper motor location


drivers side of the engine compartment.upper firewall area,directly behind the brake booster(big round disk looking thing)

Feb 08, 2013 | 1979 Pontiac Firebird

1 Answer

We have a 1979 bronco with a 460 put into it... i am willing to take any suggestions b/c im at my wits end, went through countless solinoids, an alternator and a starter,and still the truck does not...


several possibilities. 1) Take you battery to your local auto parts place and have it checked. 2) make sure that there is no corrosion on the battery terminals. 3) place a volt meter on the battery while it is running. If it is 13.6V to 14.3V that it is charging. If it is lower, than the voltage regulator (should be on the firewall or fender) is probably defective. 4) check the wiring between the voltage regulator and the battery. Good luck!

Apr 05, 2011 | 1979 Ford F 350

1 Answer

I have a 91 bronco w/ a 351w. I need to replace the ignition control module. Do I need to pull the distributor? If so, is there anything special I need to do as far as putting the distributor back in?


the ignition control modual is not in the ditributor but either atatched to the side of the distributor or located on the firewall/fender well.removing the distributor is not nessisary.

Nov 19, 2010 | 1991 Ford Bronco

1 Answer

Ford 351 windsor engine diagram


ford-351-windsor-engine-diagram-p05qnqdskqjeezv3eiltmave-1-0.jpg Here's a mechanical blow-up of an 80's 351w engine.



ford-351-windsor-engine-diagram-p05qnqdskqjeezv3eiltmave-1-2.jpg and the firing order layout.
hope this helps...

Jun 23, 2010 | 1991 Ford Bronco

1 Answer

I have a 1994 ford bronco with a 5.8 351w. when ignition is turned to accessories the fuel pump will come on for 2-3 sweconds then go off,but after a few minutes it will come on and stay on. when the...


Take your Bronco to an Autozone or Oreillys for a free scan. Offhand a new ignition switch would seem like a good idea, because the fuelpump should not be working in the ACC position.
If a new ignition switch does not help the fuelpump problem the pump is wired to an accessory. You need to look up the fuse info in an owners manual.

Dec 01, 2009 | 1989 Ford F 150

1 Answer

Took the efi 5.0 out my 89 bronco and installed a 351w carburated out a 84 bronco.wiring in the 84 was screwed.replaced the distributor with a points distributor and coil and no matter how i wire it it...


I dont know what "points distributor" you installed or how you made sure you installed it correctly. But a more simple way would be to get a distributor that has the coil pack built in. That kind only would require 2 wire connection. Positive 12 v and ground. also it has a 3rd connection you may use that is for the tac. very simple.
The one you have now ... do you get spark to the spark plugs. If so I would fool around more with being sure it is installed correctly, find TDC and be sure the rotor is pointing to the #1 cylinder, ALSO that you have the plug wires going in the right order on the cap. I dont think you will have luck with the computer compatible question.

Oct 01, 2009 | 1989 Ford Bronco

1 Answer

Wondering I have a 1986 ford bronco II I am wanting to put a 351w in it is there any way to get a wiring harness for that that will plug into the engine any my bronco


will a bronco 2 have enough clearance for the 351? i know the motor mounts are different and i am sure the tranny and transfer case wont line up right....i am not sure a wiring harness is gonna be your biggest worry here

Jul 18, 2009 | Ford Bronco II Cars & Trucks

Not finding what you are looking for?
1979 Ford Bronco Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...