Question about Cars & Trucks

1 Answer

How do i install 1/4window rubber

Nothing yet

Posted by on

1 Answer

You use a bit lenght of paracord
its cord made for parachutes

look on ebay
and a little bit of washing up liquid mixed 50 50 with water
and paint it on the rubber and the rest

happy days and nice and easy
look on you tube how to rework a rubber seal on a car window
or similar video
lots of tutorials there watch a few first

Posted on Dec 09, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the rubber boot,does it go through the bottom of control arm?


this cannot be answered because it refers to nothing, no make , model year, what the rubber boot covers --nothing
ask your question again giving all the details as questions are not linked on this site

Jan 11, 2016 | Cars & Trucks

1 Answer

How to replace the exhaust system on a 2001 Chrysler Sebring LXi?


Two or three bolts at the exhaust manifold. Heat them to get them off. Cut the rest off with a saws-all. Don't cut the rubber hangers, reuse them. Weld or use hose clamps to re install.

Feb 01, 2015 | 2001 Chrysler Sebring

1 Answer

How do I install the bed on a 2004 Dodge Dakota


Where the frame meets the bed directly you should need no rubber or shims. Some beds have raised areas that need a bushing to fill the gap between the bed and frame but most need nothing. Body shops do use shims on beds to get them level if there have ever been any accidents, the frame is out of plum or the bed is not level. So if you get it on and it is too high or low an any certain area just shim it up till it gets where you you want it and looks level and fit.

Oct 17, 2014 | 2004 Dodge Dakota

1 Answer

Fuel leak


You need to be a little more specific in your questions, but we'll take it in its rawest form. A fuel regulator is nothing more than a pressure valve. It either has a rubber diaphragm or a piston and rubber o-rings and rubber seals. If you have external leaks, you have a degraded rubber seal. The only option is to replace the unit with a new or used regulator.

europartsplus.com

Sep 08, 2014 | 1996 Ford Explorer

1 Answer

Car does nothing in reverse gear,on newly installed 350 turbo trans, that sat on garage floor,out of car for an extended amount of time..


i would use a little rubber alcohol a few table spoons in the tranny because it will make the seals swell a little bit might work after that

May 09, 2014 | Cars & Trucks

3 Answers

The thermostat will not stay in place no rim to stop it from falling in side engine housing i have the rubber that ataches on part but theirs nothing to stop it from falling in side first i've ever saw...


Buy a can of permatex gasket adhesive. Spray dome onto the gasket, thermostat housing and thermostat (make sure only to apply to where the gasket contacts the thermostat) and let it set up. It acts as a contact cement and will make it much easier to install your thermostat.

Mar 08, 2011 | Buick Century Cars & Trucks

2 Answers

How do i install a manual antenna


Manual Atenna?.. -- unscrews and screws?? (counter-clockwise to 'UNSCREW' and 'CLOCK-WISE' to screw in the new one.... pretty simple... ya think?

Feb 20, 2011 | 2002 Hyundai Accent

1 Answer

The crank shaft pulley was out of alignment when i was changing the serpentine belt. when i tried to push it back on a rubber piece came out one side. so i pulled the whole thing off to reset the whole...


That rubber piece was probably your front crank seal. I would recommend replacing it now as there could easily be nicks in it and it will puke engine oil all over the place while you drive. A new one should only cost between 10 - 15 dollars. When you install the new one try to install it as evenly as possible all the way around. Then on your crankshaft pulley there will be a keyed slot, put a little bit of silicon inside the slot before installing it back on the vehicle. This will help stop leaks. Put the bolt in the pulley and tighten it until it completely seats, this should align it with all of the other pulleys and you should be good to put the belt back on.

Feb 16, 2011 | Chevrolet Malibu Cars & Trucks

1 Answer

How do you install a thermostat on a 2.4L grand am 2000 4cyl?


this was not a 1997 Cavalier it was a 2000 pontiac grand am. did not put a thermostat in it . I put it back the way it was.

Nov 25, 2008 | 1997 Chevrolet Cavalier

1 Answer

Self installation of front windshield


Wrap rope in the inside of the windshield gasket with the window in place. Lay the window in place and from the inside of the car, pull the rope. The rope guides the windshield gasket to the inside of the windshield opening and next thing you know it, the windshield is in place.

Jul 01, 2008 | 1984 Volkswagen Jetta

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...