Question about 2010 Mercury Mariner

1 Answer

Where is the OBD connector on a 2010 mercury mariner

Nothing at this time. I just need the location.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert that has over 500 points.

  • Expert
  • 213 Answers

Hi Chad,

Here is a follow up for you. The picture provided is from a 2005 with the OBD location. .

Looking at many examples on line from all applications. The majority of these plugs are under the steering column. Either right or left mounted under the dash board.

On some foreign models . Remove the droor between the center console. And it will be mounted on the floor between the seats.

Fare . Well.

Posted on Dec 09, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2010 Mercury mariner squeals while acceerelating. All belts, etc have been checked.

If not the belt or tensioner, check belt driven components, see if pulley is trying to sieze? Turn the pulley, where applicable, can you feel or hear anything? Try to move pulley in and out, up and down, too much movement?
Sometimes you use long steel bar of some kind, engine idling, Tip of bar/rod touches accessory housing, the other end goes on that bone behind your ear, helps to magnify the sound. listen to each component in turn, see if you can locate the sound. Be careful not to get the rod or your clothing caught in pulleys or belt, safety is your responsibility. I guess you could use a mechanic stethoscope to listen.

Sep 04, 2017 | 2010 Mercury Mariner

1 Answer

How to reset tire low light on 2010 Mercury mariner

THe light will reset it self the computer will reset but all the tires have to have 32 psi then drive it about 5 miles it will reset if not you have a bad tire sensor usually if you had a tire flat fix that the one that will be bad becusa when the remove it they alway Berkeley the sensor good lucl

Oct 03, 2015 | 2010 Mercury Mariner Hybrid

1 Answer

How to replace brake pads on 2010 mercury mariner

There is lot more to brake service or work than
just changing pads

Watch some You Tube Video

Sep 26, 2014 | 2010 Mercury Mariner

1 Answer

Change rear brake light on a 2010 mercury mariner

Well, here is an article which may about how do I replace rear brake pads, I hope it might have help to you.

Aug 01, 2012 | 2010 Mercury Mariner

1 Answer

I just bought a 2010 mercury mariner premier 4 cylinder with 75,000 miles. When should the timing belt be replaced? Any other maintenance I should plan on?

The owners' manual will designate when to inspect it.Replace it before 100K to be safe, and assume it's never been replaced unless you have its history. don-ohio

Sep 09, 2011 | 2010 Mercury Mariner

1 Answer

My OBD port is not working on my mountaineer and i went to change the fuse for it and there is no fuse on that Location on the fuse panel..just wondering if this is normal. 2000 mercury mountanieer with...

sometimes you have to wigle the OBD 2 connector on the tester. Sometimes, you have a tool that does not communicate with your OBD 2 system. Go to Autozone and have them do a free scan to see if their tester works.

Fuse 17, 25 amp, yellow in dash fuse panel supplies 12v

PIN 16 Orange, lower right I think is 12v all the time.

Jul 27, 2011 | 2000 Mercury Mountaineer

2 Answers

2005 Mercury Mariner Problem: A/C fan control only work when it's turn on to the do I solve this problem

Most vehicles have a blower motor resistor located on the blower housing. It probably needs replacing. Check the wiring connector too. Sometimes a loose connection can melt or damage the connector.

Nov 03, 2010 | 2005 Mercury Mariner

Not finding what you are looking for?
2010 Mercury Mariner Logo

310 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts


Level 3 Expert

76051 Answers


Level 3 Expert

5516 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides