Question about Cars & Trucks

1 Answer

When my motor start getting hot it stop and I can started right away but stop again soon as I put it in gear coud't be the coil

I wait until the motor get cold and it,s okay until it get warm again

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 110 Answers

Yes, that is very typical of a bad coil, but to be sure, test for spark, when the engine has died.

Posted on Dec 10, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pt cruiser transmission stick


I would go by the hot reading of the cars transmission fluid. Check while in park and idling, check as you stated on level ground. Wait until the car temperature reaches normal operating temperature then check the fluid, not once but at least two, even three times to make sure your reading is accurate. If it shows a cold reading still then add fluid until it is within the hot reading area/marks. NOTE: be aware that when it says hot meaning the fluid in the transmission is hot, not just the cars motor. So you may want to drive it around to warm it up then come back and park it on a level surface and leave it running. Wait 5 mins or so then go out and check the fluid, again it should read between the hot marks if not, add until it does. Hope this clarifies the proper way to check your transmission fluid.

Apr 17, 2014 | 2006 Chrysler PT Cruiser

1 Answer

When my 1972 chevrolet 350 4 barrel is warmed up it acts like its not getting gas and jerks and eventually dies. if i wait a few minutes it will start up but after slight acceleration it starts it aga


Good chance it is not getting fuel, or enough fuel.
When the rig is cold, the choke is closed. As it warms up, the choke opens.
If the metering jets inside the carb are dirty, they may not be letting enough fuel into the barrels. You could also have a vac leak that is masked by the choke until the engine warms up.

Jul 21, 2012 | Cars & Trucks

1 Answer

My 2004 RX8 won't start when the engine is warm, when its cold it starts no problem. If I drive the car till it at operating temp and shut it down I have to wait an hour until start it again


if this car is on the cold start injector when it is defective. Injects additional fuel to the engine is still warm. Is it to feel warm by running more than normal gasoline smell?

Mar 15, 2011 | 2004 Mazda RX-8

1 Answer

When the motor is cold and the outside temperature is below 70 the car will not stay running. Will die with in 30 seconds or so of starting, then you have to wait a minute or two befor the car will start...


Are there any service engine soon lights on associated with this problem?

Possible CTS (Coolant Temperature Sensor) or another sensor giving faulty data for the cool air temperature.

Check spark and gas delivery when cool, below 70 deg. If the spark is not being delivered or the fuel injectors are not delivering fuel at this temperature, it will explain why it doesn't run right until it is warmed up.

Oct 08, 2010 | 2001 Ford Windstar

1 Answer

Heat isnt working...place on heat and turn on but it just stays cold?? Its been like this for like a week or so..it was doing this then started for a few days where it would kinda get warm again and then...


Try bleeding the air out of the cooling system. At the front of the engine, on top, should be a bleed valve. It's small, and looks similar to a grease fitting. This is the highest point in the cooling system and eventually all air in the system will accumulate here.

Make sure the coolant reservoir is serviced to the correct level. With the engine cold, but running, open the bleed valve until coolant starts coming out. Close it and wait for a few minutes. Keep opening it intermittently until no more air bubbles out -- until the engine is warm.

Oct 24, 2009 | 2002 Dodge Intrepid

2 Answers

Starts runs until warm stops


I would replace the coil. and condenser.

Oct 18, 2009 | 1989 Jeep Cherokee

1 Answer

2004 Odyssey, heat and A/C do not work unless van in motion


Since warm air eventually comes out when the vehicle is in motion, you may have an air mix door that is stuck in fresh or is somehow blocking warm air from the heater core.

To see if the air mix control motor is bad, you need to retrieve your Diagnostic trouble codes (DTC's) from the heater control panel. To run the diagnostic function, do the following:
1. Turn the ignition switch ON (II).
2. Turn the fan switch OFF.
3. Press the recirc control button to select Recirc (recirc light on.)
4. Press and hold the recirc button to select Fresh (recirc light off) and continue to hold the button down until the recirc light comes on for two seconds and then goes off.
5. If the system is okay, the recirc light stays off.
6. If there is a problem, the recirc light blinks the DTC to indicate the trouble. One blink=a problem in the air mix control motor circuit. Two blinks=problem in the mode control motor circuit
Three blinks=problem in evaporator temp sensor circuit.
7. Turn the ignition switch off to cancel the self diagnosis function. Run the diagnostic again after repairs are complete.

Note: the air mix control motor has a rod which connects to a plastic link. The link controls the mix doors and also connects to the heater control water valve via a cable. The air mix motor may check okay, but if the link is broken then you will still have problems. the motor is on the bottom of the heater unit in the front passenger's foot well.

May 10, 2009 | 2004 Honda Odyssey

1 Answer

AC is cold, then hot..


you need the tempature blend door motor. My 01 silverado had this issue about 1 1/2 years before i was tired of messing with it they are not hard to replace. The cover (if it is still on) for passenger side floor ducts needs to be removed and the motor is near the right side of "hump" (trans tunnel) mounted horisontial with the armature pointing upwards.

Apr 27, 2009 | 2000 GMC Sierra

2 Answers

4 cyl Engine starts and idles ok...give it throttle and it dies


I need to get a clear mental picture of what exactly is happening.

With this said, you stated that the car "runs fine" until warmed up.

Q: When you start the car when cold it idles fine?
Q: If you allow the car to idle until "fully" warmed does the car stall?
Q: As the car begins to warm up, Does the RPM fluctuate abnormally?
Q: Does the car Only stall when you press on the gas pedal or does it stall just sitting and idling in addition to pressing the gas pedal?
Q: If you can drive it while cold does the car stall during acceleration when warm or only at Stop Signs / Lights?
Q: If you wait 20min or so, can you start the car again?
Q: How many miles are on the car?

Mar 27, 2009 | 1995 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...