Question about 2011 Dodge Avenger

1 Answer

Need to drain transmission fluid change filter reinstall pan gasket reinstall refill transmission

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 137 Answers

See the manual.

Posted on Dec 09, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change the transmission oil filter in a 1999 isuzu rodeo


Drain transmission fluid. Remove transmission oil pan. Remove and replace transmission filter. re-install oil pan with new gasket and refill with new transmission fluid.

Jun 29, 2014 | 1999 Isuzu Rodeo

2 Answers

Where is trans filter located


Hi,
The follwoing is from the GM Shop Technical Manual.
Changing the filter requires removing the transaxle oil pan and gasket,
Remove or disconnect

bendarden.jpg

  • Raise vehicle and suitably support.
  • Loosen oil pan bolts and drain fluid,
  • Remove oil pan attaching bolts.
  • Remove pan pan and gasket.
  • Remove the oiil filter using a long screwdriver pry filter neck out of the seal.
  • Check oil filter seal for damage or wear. If needed, remove and replace
Install or connect
  • install new oil filter and/or seal.
  • install the old pan gasket since it can be reused, unless sealing ribs are damaged. If damaged, use new gasket.
  • Install the oil pan and attaching bolts.
  • Tighten pan bolts to 13 lb. ft,
  • Lower vehicle.
  • Refill transxle to proper level with DEXRON III or DEXRON-IIE fluid.
  • Checkoil pan gasket for leaks,

May 21, 2011 | 1995 Buick LeSabre

1 Answer

How to change transmission fluid on 2005 Chevy Express


Purchase trans fluid & filter kit from parts store. With vehicle parked and wheels chocked, undo trans pan slowly loosening bolts allowing one corner to allow fluid to drain (into a catch container of course). Pull pan once drained, remove old gasket, undo screws holding filter in place, replace with new filter, attach gasket to pan, retighten pan, refill.

Mar 05, 2011 | 2005 Chevrolet Express

2 Answers

Changing automatic transmission fluid?


on the bottom of the vehicle you will see a large rectangular pan with about 20 -10, or 12mm bolts.
you have to remove the bolts in such a way as to let all the fluid inside it, be drained from one point as you remove all the bolts. once removed remove the filter inside the pan, and if its a cork gasket going on, dont tighten it up too tight as to pinch the gasket. reverse to install, then fill with type F transmission fluid, about 4 to 6 qts.

Jan 02, 2011 | 2006 Ford Escape

1 Answer

So..I'm a female nerd!! How and can I change the transmission fluid myself? It is a 96 chevy blazer 4 wheel drive


It's not too hard at all. You'll need a decent size drain pan. You'll want to remove all but a couple of the transmission pan bolts on the bottom of the transmission. Let the fluid drain out as you loosen the last couple bolts. Once most of the fluid has drained out, remove the last couple bolts and let the pan done and pour out the remaining fluid, discard the old pan gasket. I would also replace the transmission filter, the new filter should have a new pan gasket with it. Remove the old filter, install the new filter, use some gasket cement to glue down the new gasket to the pan and reinstall and fill with new fluid. I would also check your transfer case fluid level, the transfer case is behind the transmission.

Nov 18, 2010 | 1996 Chevrolet Blazer

1 Answer

I need to know how to change the transimission filter on a 1996 ford thunderbird v8. Or at lest where to find a diagram on how to do it


Copied from AutoZone.com:


REMOVAL & INSTALLATION


See Figures 1 and 2
  1. Raise and safely support the vehicle on jackstands.
  2. Place a drain pan under the transmission.
  3. Loosen the pan attaching bolts and drain the fluid from the transmission.

Always place used fluids and oils into a sealed storage container and take to an approved recycling collection facility. Never dump used fluids or oils on the ground or in a trash receptacle. Contamination to the environment can and will occur.
  1. When the fluid has drained to the level of the pan flange, remove the remaining pan bolts working from the rear and both sides of the pan to allow it to drop and drain slowly.

Some AOD transmissions will have a plastic plunger type plug floating loosely in the pan when draining the fluid. It is of no importance and was used in the assembly process of the transmission. Discard it before reinstallation of pan.
  1. When all of the fluid has drained, remove the pan and clean it thoroughly. discard the pan gasket. If equipped, remove the pan magnet.




0900c1528006bc40.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Unfasten the remaining bolts, then remove the transmission fluid pan from the vehicle



0900c1528006bc41.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: On some vehicles, such as this 1995, you must remove and clean the pan magnet
To install:
  1. Place a new gasket on the pan, then install the pan on the transmission. If equipped, don't forget to install the pan magnet. Tighten the pan attaching bolts as follows:

    C3 and C5 Transmissions: 12-16 ft. lbs. (16-22 Nm) A4LD Transmissions: 8-10 ft. lbs. (11-13.5 Nm) AOD Transmissions: 71-119 inch lbs. (8-13 Nm) 4R70W Transmissions: 9-11 ft. lbs. (12-15 Nm)
  2. Add the correct type and quantity of fluid to the transmission through the filler tube.
  3. Lower the vehicle. Start the engine and move the gear selector through shift pattern. Allow the engine to reach normal operating temperature.
  4. Check the transmission fluid. Add fluid, if necessary, to maintain correct level.


FILTER SERVICE


See Figure 3
  1. Remove the transmission oil pan and drain the fluid. For details, please refer to the procedure located earlier in this section.
  2. Remove the screen and the filter from the valve body. Most screens are retained using a fastener; through some may use an interference fit between the screen tube and valve body.




0900c1528006bc42.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: After the pan is removed, you can remove the transmission fluid filter
To install:
  1. Install a new filter using a new gasket or O-ring.

If the transmission uses a filter equipped with a fully exposed screen, it may be cleaned and reused.
  1. Install the transmission oil pan and properly refill the transmission.

Aug 26, 2010 | 1996 Ford Thunderbird LX

1 Answer

Change transmission pan gasket


Drain the fluid through the allen drain bolt, if equipped.
Retorque drain plug to 36 foot pounds

Remove the 10mm bolts around the perimeter of the transmission pan.

It often helps to loosen the transmission mount and pry the transmission up to aid in access to some of the bolts.

Drop the pan and remaining fluid.

Clean the pan with brake parts cleaner or equivalent, do NOT use a lint producing rag, let it air dry.

Install a new cork gasket, NO sealant and reinstall pan with bolts torqued to 43 inch pounds.

Refill transmission fluid with 3-4 quarts fluid. Check level once warmed up and adjust if necessary.

Oct 16, 2009 | 1997 Toyota Camry

1 Answer

I would like to change the transmision fluid in my 1996 s-10 pickup 4.3 eng any advice???


Unfortunately GM didn't put a drain plug in the transmission pans. You'll need a transmission service kit which will have the filter and new pan gasket. Put a large catch can under the pan, loosen all the bolts and crack the pan loose from the transmission and allow the fluid to leak out. Next remove all but two bolts letting the fluid drain as you go. With one hand on the bottom of the pan supporting it remove the last two bolts. Lower the pan down and drain the rest of the fluid out. The rest is pretty simple and hopefully less messy. Wiggle the transmission filter out, remove the grommet and replace it with the one supplied in the kit. Clean the pan, especially the magnet of metal shavings. Clean the gasket surfaces. Place the new gasket on the pan and thread a bolt in each corner into the gasket. Bolt the pan up and refill with transmission fluid.

Apr 05, 2009 | 1996 Chevrolet S-10 Pickup

2 Answers

2003 Dodge Stratus


no drain plug, no car or truck has had a drain plug for decades, reason? they want the filter changed with the fluid, so they make you pull the trans pan to drain the fluid, one very messy job.

Feb 12, 2009 | 2003 Dodge Stratus

1 Answer

Transmission fluid change


More than likely, like most automatic transmissions, yours does not have an oil plug. You need to drop the transmission oil pan to drain the old oil... You need to buy a transmission filter/pan gasket kit. The filter is located on the bottom of the tranny. You will see it when you remove the pan. Replace the filter, thoroughly remove any traces of old gasket material, clean the mating surfaces, and reinstall the pan with the new gasket. Torque the pan bolts to the manufacturers spec (you should be able to get this where you buy the filter/gasket kit). Refill the transmission through the dipstick (Capacity for the Voyager is 4 quarts, make sure to use ATF Plus (Type 7176) for your particular tranny, NOT Dexron, Mercon, or generic automatic transmission fluid, Chrysler transmissions do not like any other kind and tend to fail quite quickly with the wrong fluid). Fill to the full cold level. Start the engine, move the shifter through all gear ranges, and put it back in park. Leave the engine running and refill to cold full. Drive the car for 5-10 minutes and, with the engine still running and the car in park, fill to Hot full. You should be ready to go!

Aug 26, 2008 | 1997 Chrysler Town & Country

Not finding what you are looking for?
2011 Dodge Avenger Logo

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...