Question about 1988 Jeep Cherokee

1 Answer

1988 Jeep Cherokee - can a cooling fan hub bearing be replaced?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 190 Answers

Anything can But it would be cheaper to replace it since you most likely can't get a part number off the old one let alone they are pressed in and for you to remove it and attempt to repress one in IF you can find one will be a nightmare, . around 60 buck from an auto parts store or about 9 hours to attempt to replace 1 with no idea of how long it will last if you find it.. Good luck. BCB

Posted on Dec 09, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: How do replace front axle bearings on a 92 jeep

You have to pull off the wheel, brake assembly, and rotor. If it is a 4x4, i suggest you take it to a mechanic. If it isn't, once you pull all that off you will see a little cap cover. take a small screwdriver and pop off the cap. There will be a clip. pull off the clip and pull out the axle bearing. Make sure you grease the axle bearings before you put the new one in. Then put it back together in the reverse of these instructions. Hope this helps.

Posted on May 02, 2009

  • 6982 Answers

SOURCE: 2001 Jeep Grand cherokee cooling fan runs on

Likely your fan relay internal contacts have burned closed. Relay should be either in the power distribution center or in front of the battery.

Posted on Nov 06, 2009

  • 59 Answers

SOURCE: cooling fan not kicking on causing the jeep to

Check the fan operation by disconnecting the fan wiring. Using the battery use a set of jumper wires to see if the fan runs directly off the battery.

Posted on Jan 18, 2010

  • 11800 Answers

SOURCE: my cooling fan stays on my 2000 jeep cherokee.

That is normal, the system is designed this way to prevent the overheating of the engine's head when you shut down the engine without allowing it to cool itself to an acceptable temperature.

Posted on Jun 19, 2010

ZJLimited
  • 17970 Answers

SOURCE: 2002 jeep grand cherokee replaced radiator cooling

The airbag light will come on and stay on as long as there is an active code in the system, this means that something is malfunctioning right now so we will turn the light on. You really need to have the codes checked for an accurate diagnosis.

Its possible that you have some problem or your sensor go to bad...

1. Disconnect and isolate the battery negative cable. Wait two minutes for the system capacitor to discharge before further service.
2. From the engine compartment, disconnect the right or left headlamp and dash wire harness connector for the front impact sensor from the sensor connector receptacle
3. From the engine compartment, remove the two screws that secure the right or left front impact sensor to the sensor mounting bracket on the right or left radiator support vertical member.
4. Remove the front impact sensor from the sensor mounting bracket.

zjlimited_214.gif

That is for replacement, you just reverse the list for install.

Hope helps.

Posted on Feb 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you repack front wheel bearings on a 98 Cherokee 4X4


OP<
Posted by J Sparacino on Aug 31, 2016
you double posted. why do that????
no, the hubs are integrated bearing hubs.
here read the parts pages,
see any tapered bearings there,
if not sold , pray tell , how can you pack the bearing not in hand.
not only that, there are like 1000000 books on how to pack front bearing, if they were removable and are not.
why not look first then post.? at car and the book, !
or read the FREE FSM, it says what ?, unbolt them
and replace the integrated hub assembly.
that is a fact. 300 times ive posted the free book, now.
and is still there, and the words still real ,still jeep words and all accurate. sigh.
below is rockautos list of after market hub assemblies.
do not get confused at those needle bearings, those are actually front axle shaft bearings, not hub wheel bearings. fact.
wheel bearing are ball or tapered rollers, to handle lateral huge loading.

http://www.rockauto.com/en/catalog/jeep,1998,cherokee,4.0l+l6,1315943,brake/wheel+hub,wheel+bearing+&+hub+assembly,1636?a=Referer+duckduckgo.com+URL+%2F

56a4ac86-d271-4704-9005-ab6d4f0bc76f.jpg

Aug 31, 2016 | 1998 Jeep Cherokee 4WD

2 Answers

How to repack front wheel bearings on a 98 Jeep Cherokee 4X4


YOU CAN"T is the short answer..... sorry,, RTM much>?
ive posted the free fsm like 300 times now on this car.
ever like search.?
first off, on all cars made, what the factory made or dealer sells ins one thing, what the after market does, is another.
a fact.
in fact some cars with Integrated hubs new, the aftermarket sells them and sells the rebuild kits too.
the book covers the service step by step.
what parts you use or by is your call.

now ill read that book for you.
btw I sold my 99 but not the books.
XJ jeep, the book is here, (over 301 posted,)

http://www.morris4x4center.com/knowledge-base/index.htm?utm_source=cj#service

at least you said its 4wd, not all are. 2points for that.

USA XJ jeep, 1998.
1988 pages.
the trick is learning how to navigate the book , chapter #
the fact is we look first, you didn't, what is there who knows.?
maybe the last shop put on serviceable hubs. right?
if you had looked at the back side, you'd have seen 3 bolts
holding it on. and that tells you what?, that they are integrated hubs.
on new car, and at Jeep parts counters. world wide.



26271221-ky1blxw0v1am10ilppsnvnq2-3-0.jpgnow lets do this backwards
lets pretend to buy the part, hark , you can online.
and see all the makers of parts aftermarket in 1 click
no kidding, a fact.
see the 8 makers here,(can be more)
all are 100% integrated, hubs, (not saying there are not other makers, or kits, the world is a huge place and I cant tell you
all answers world wide for sources)

you could off them, take them both to a shop, and ask for them to rebuild them at $100 /hr labor, but, i bet they just laugh at you.
I'm not. but why not just remove it , check it and if bad replace it.
take it to any auto-store in town, NAPA is best. and set it on the counter, and say, got this, answer yes.
how to repack unpackable bearings,.DIY.

shorter answer, R&R it.
get a shop to fix it.
buy the part first, and see what you got first.
look at it and ponder packing it.

Aug 31, 2016 | 1998 Jeep Cherokee

1 Answer

2007 jeep cherockee r front hub replacement


there is no Cherokee, here, usa, only GRAND Cherokee
if not in USA< now's that time to say, our books are not for your car. nor parts.

answering for 2007 WK jeep USA.
can , what does can mean.? I can !
all parts on all cars can be replaced
what are you asking, please.

why not post symptoms first
then say what you've done so far.
then ask how to solve a specific problem.
is this a 4wd question? on 4wd parts or just the wheel bearing hub question.
tell what bad..
eg:
hello, my wheel bearing is bad, (play and noises)
what are the steps to repair it.
easy read the manual
its all there.

click wk
then see chapter.2
see pages
11
and read. starting there.
the parts are here at jeep
see? them?

toss COIN land on 2wd (aka, 4x2)
http://www.factorychryslerparts.com/products/JEEP/2007/GRAND-CHEROKEE4x2--37L-V6--5-Speed-Auto-W5A580/HUB-AND-BEARING-Right-or-Left-Brake-Front--Includes-16-21-22/4414630/52089434AE.html

that be a wild guess on your drive line.....

Feb 24, 2016 | Jeep Cars & Trucks

1 Answer

I need to know what the part is that the fan clutch bolts onto with 4 bolts on the shaft for a 1995 jeep grand Cherokee 4.0?


the fan is bolted to a viscous fan hub. It is designed to have silicone fluid in one half of the hub and when the engine starts cold it locks up and drives the fan until the fluid is pumped back to the other side or reservoir in the hub. It is held there and the fan now spins free When the radiator gets hot there is a bi-metallic strip that holds a valve cluse and this strip bends and allows the valve to open and the fluid is thrown by centrificale force back into the front section and the fan is then jammed because it gets more than it can pump back to the reservoir. The fan spins and draws air through the radiator and cools the coolant down. As the coolant cools down so the metal strip closes off the valve and the fan eventually free wheels again until the next stop where the action is repeated. . If your car has one of these hubs and it tends to over heat when stopped then the hub is the main cause and should be changed. The noise is the fan spinning until the fluid is moved out of the front section

Jan 01, 2014 | 1995 Jeep Grand Cherokee

1 Answer

Left side of jeep I hear a bearing noise


Check front diff. oil level,use only jeep spec.oil and pop in some jeep transmission conditioner,if that`s not the cure it maybe diff. bearings(not a bad job to do)...Good-luck..

Dec 30, 2012 | 2004 Jeep Grand Cherokee

1 Answer

Replace Front Wheel Hub Bearing 2002 Jeep Grand Cherokee 2 wheel drive


Removal
  1. Raise and support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the brake caliper, caliper anchor, rotor and ABS wheel speed sensor.
  4. Remove the cotter pin, nut retainer and axle hub nut.
  5. Remove the hub/bearing mounting bolts from the back of the steering knuckle. Remove hub/bearing from the steering knuckle and off the axle shaft.
Installation
  1. Install the hub/bearing to the knuckle.
  2. Install the hub/bearing-to-knuckle bolts and tighten to specification.
  3. Install the hub washer and nut. Tighten the hub nut to specification. Install the nut retainer and a new cotter pin.
  4. Install the brake rotor, caliper anchor, caliper and ABS wheel speed sensor.
  5. Install the wheel and tire assembly.
  6. Remove the support and lower the vehicle.

Apr 22, 2012 | 2002 Jeep Grand Cherokee

1 Answer

I have a 1988 jeep cherokee and it has a loud squeelling noise and small amounts of smoke that come out of the defrost vent any thoughts?


Sounds like the fan motor is shot...or the fan impeller itself is rubbing on something...more than likely..the motor is shot and you will need to replace it

Jan 17, 2011 | 1988 Jeep Cherokee

1 Answer

How do I change the axel on a 88 jeep wrangler? the u joints need to be replaced and I need to know where to start


Start by removing the center axle nut. (torqued very tight about 175ft lbs...you need a solid breaker bar with about a five foot pipe added for leverage, or 3/4 impact gun. then remove wheel and caliper and rotor. Remove the hub bearing by taking out the three 12pt bolts on the opposite side of the steering knuckle. Once those bolts are loose use wd40 on the hub parting line and hammer on the bolt heads to push the bearing out.Loosen the bolts each time they need to be backed off till the hub is loose. The axle comes out right through the hole where the bearing was. Make sure you grease the joints well because you cant once it's back together.

Jul 16, 2009 | 1988 Jeep Cherokee

1 Answer

1988 jeep cherokee engine problem


Bearings (including main bearings) as well as rear main seal require engine removal to do it correctly. If the engine is tired, then get a different one. Otherwise your determination, financial situation and skill level will tell you what you need to do.The entire job is not difficult but takes some time and you need to make precise measurements in order to get it right. (change oil pump with bearing sets) Parts prices can be found at napa online as well as numerous other places. If you need help along the way, someone here will be happy to help!

May 20, 2009 | 1988 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...