Question about Ford Cars & Trucks

1 Answer

Can you put ford xr6 body control module into a ford xr8 when l looked at my body control module two of the black wires coming two of the wiring looms have been cut and can't find the end of the ones where they go to behind the dash

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Ford Master
  • 2,553 Answers

Check the model numbers it they are same you can swap.

Posted on Dec 09, 2014

Testimonial: "l don't think you under stand the the question Stand have a read of it again."

  • michael bombardieri
    michael bombardieri Dec 09, 2014

    some expert when l swap will my wires l need to join up again will they just grow back or do l water them Stand you need to have a sleep go have a lay down mate.

  • michael bombardieri
    michael bombardieri Dec 09, 2014

    stand stop taking drugs

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Peugeot xr6


have you checked for spark with plug in wire while cranking

Apr 14, 2013 | Cars & Trucks

1 Answer

I need to locate and change the Intake Air Control Unit on a 2000 Pontiac Sunfire 2.2 liter. Where is it located? Thank you


Should be on the throttle body, look for a little cylinder shaped black object with 3 or 4 wires coming out of it, should be 4 wires though, and is held by 2 screws, to remove the 2 screws you'll need either torx or allen key set. It is called ( IAC ) = Idle Air Control valve.

If its a module or like a module look on top of the air intake hose, usually a little flat black box.

Mar 03, 2013 | Cars & Trucks

1 Answer

THE IMMOBLISER IN BY DAEWOO IS CAUSING PROBLEMS IT WONT START IN THE MORNING TAKE GOOD 10 MINS TO GET THE RED LIGHT ON THE DASH BOARD TO STOP FLASHING AND WHEN I TRY TO START THE CAR THE RED LIGHT IS BOLD,...


look for large wiring loom under steering column that is patch harness going to immobiliser module,
two black large connectors that look the same disconnect and isolate connect original loom connector from top to bottom body harness original connector and presto no more immobiliser its bypassed vehicle now works.

Sep 07, 2011 | 2002 Daewoo Lanos

1 Answer

Trying to locate spout connector on 87 ford 4.9L pickup. I know approx. where it should be, but what does it look like?


it will be in the wire loom coming of the distributor or ignition module, should be gray or black in color and be square shaped. It plugs in, hold the house and pull the plug out.

Jan 26, 2011 | 1987 Ford F 150

1 Answer

The power windows are not working at all. Tried the fuses.


ok,make sure you tried all the windows on all the door switches,,,,what i think you may find is broken wires,sounds like it,,,,,when you open the drviers side door,look in the crack where the body of the car meets the door and you will see a black wire harness,you are going to carefully cut open that harness loom with a sharp razor knife,Be careful not to cut yourself and not to cut into the wires inside the loom,,,once you got it cut open you will need to inspect the wires inside,,they get dry and brittle from all the opening and closing of the door and the wires chaff open and short and some even break apart,,ive seen 6 broken wires in 1 ion door jam,,,,all the wires for all the windos run thru here because of the master switch being in that door...,,if oyu do find broken ones go get the pinkish red **** connector,make sure they are heatshrink connectors so they are weather proof,fix all the wires and heat the connector up to shrink it tight then electrical tape over each connector seperately,then put loom back on and electrical tape the complete loom from door to body,,,,,and all should work...ive never seen a bad windows switch knock out all 4 windows so i doubt its that,,,but good luck,hopefully this helps you

Oct 29, 2009 | 2005 Saturn ION

1 Answer

Vacuum lines cut on 99 f250


Most likely goes inside the cab,for the ac/heater control,look in all the black looms under the hood,the wire looms,for some reason they run plastic vacuums threw the looms.

Aug 07, 2009 | 1999 Ford F250 Regular Cab

2 Answers

1999 cadillac deville blower dont operate. What should the voltage be at the red wire and the gray wire or the black wire ? Iam assuming the red wire should be 12 volts, the gray wire should be variable...


red black and gray are just half the connections. Red is positive 12 volts coming from fuse of circuit breaker. The black wire is either the ground or the main hot wire going to the blower motor (3 pin connection only), and the gray wire (if is is small in size) is a variable voltage coming from the body control module requesting speed for the blower motor.The blower control module varies voltage on the main wire going to the blower motor, supposedly in accordance with the requested voltage from the body control module. Usually if all fuses are okay and present on the apprpriate wire of the blower control module, the a blower motor that will not run or stays running after the key is turned off is the fault of the blower control module. If the blower control module has failed the the cause must be determined (over amping blower motor) or else new blower control module may fail when powered up.Usually blower control modules have more than three wires. Usual connections are: B+ (battery voltage) GND (chassis or engine ground), two large wires going directly to blower motor (can be any color, but are usually 10 guage in size), and an optional wire that reports voltage level back to the body control module.

Jan 11, 2009 | 1999 Cadillac DeVille

2 Answers

Looking for the Power Control Module, PCM, on 1996 F350 7.3L


The PCM will be to the right side of the steering column where it comes through the firewall as you look under the hood. there will be 2 wire looms, one is the back side of the fuse box and the other is the PCM.

Dec 29, 2008 | 1996 Ford F350 Crew Cab

1 Answer

I have problem with connection of ford xr6 electronic ignitio


the yellow blue is the + side of coil but to be safe get a test light connect one end to the negative side of battery or a good clean earth on the engine turn ignition. Check which wire has power .The one with power is for the + side of coil . Check test light on battery to make sure it works

Dec 27, 2008 | 2007 Ford F

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...