Question about Cars & Trucks

1 Answer

LC Smith #14637 I need new back & forestock (wood)

Posted by on


1 Answer

This is car question section

Posted on Dec 08, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I lost keys to 77 dodge.if i take the door lock off and take it to a lock Smith Wood it work for the ignition? Key is the same.and if so how do i remove it?

.You need to disassemble the inside door panel. It is held to the door with a couple of screws and several clips on the back side of the panel. The lock is attached to the door with a horseshoe type clip that will slide away from the lock cylinder from inside the door.There will be a rod attached to the cylinder with a metal clip that you will also have to disconnect. It may be easier/cheaper to change the ignition cylinder and have new keys ( supplied with cylinder ) than go to lock smith

Apr 11, 2015 | Dodge Cars & Trucks

1 Answer

What is the age of my Smith & Wesson 32 calb lemon squeezer gun?

Go to and ask how old is a smith and wesson 32 caliber lemon squeezer gun #L88176

Jan 04, 2015 | Cars & Trucks

1 Answer

Unlock steering wheel & ignition cyclinder to replace it with new one

double posted backup one (i gave 3 choices there)
define cant. (cant figure)
or the anti-theft bolts confusing you , the FSM covers all that
why not read that first. then ask questions.

to make cars not easy to seal they make it like this,
90 to now.
it needs to be removed the whole assembly.
anti theft bolts,off, , assmbly off, may take steering wheel off too.
the hand to lock smith (just did a 91) and he
uses special smith drift pins to drive the hidden (backside away from thieves, internal lock pin, he tumbler comes out or he drills it out.
then a new pin, and holding new tumbler, and then test it , ok ,
the reversses all above.
the fsm covers this all step by step, why must you avoid books.
or read

Oct 18, 2014 | 1994 Toyota Camry

1 Answer

2008 sequoia jbl no sound

my guess, is you didnt read the operators guide.?????
and the warning, "back all NAV and RADIO codes", so when
the battery dies, (it will) you dont need to go to the dealer.
posted 30 times.. now. just me and 1000 others, (i searched)
so if the battery died, the radio shuts down the amp. but
you can see scans work. ?
it does this because (all newer cars) to stop thieves.
they pull the battery, and horn , take the radio , and bingo its just a brick to them , in fact we call it, bricking the radio.

any dealer can give you the code or any certified lock smith.

its a new world, and i bet we both dont like it....

Jan 20, 2014 | Toyota Sequoia Cars & Trucks

1 Answer

How do I replace motor mounts on a 1989 Honda Accord LXi 2dr? Am I suppose to support the engine with a jack by the oil pan and if so, should I put a piece of wood between the jack and the oil pan to not...

You got it
Wood under oil pan
May need a long pry bar also
Just don't pry on any aluminium items,trans case
& such.
Do all motor & trans axle mounts & be done with
not having to come back there ever again
Support the car with jack stands & be careful when
raising the engine some, that the sub frame stays
on the jack stands & only the motor moves just
enough to get the mounts out.

Jul 19, 2013 | Cars & Trucks

1 Answer

Brake pads

The part that is hitting it is the brake caliber. The piston needs to be pushed back in. Get a 4-inch clamp and a piece of wood and put the wood over caliber, then clamp and tighten and push the piston back in.

Jun 02, 2013 | Cars & Trucks

1 Answer

2004 Honda Pilot, passenger side motor mount is leaking fluid. I can get to the bolts easy enough, but do I have to support the engine while I remove & replace this mount, or will the engine be...

yes i would highly recommend you support the engine to prevent the engine from lowering to much. you will also need to support it so you can install the new mount. use a jack with a block of wood-as wood is softer. it is perfectly safe to support the engine with the jack and wood under the oil pan.

Dec 11, 2009 | 2003 Honda Pilot

1 Answer

I need to get under the hood of my car but I my keys are locked in the car so I cant use the hood latch to pop it

Need loc smith get you in ore slim jim to pop the loc. try hanger and wedges of wood ore plastic but just warn you could scrap the window and paint up some ore crack the window if your not carfull. I borke in 2 out the 3 of my cars the ford sport trac had pay someone didnt have the secuirty code set on it to pop the doors
Cost 80 bucks and take them under 3 minutes get your car call loc smith .
Ore you could do the dumb way i did one time a diging bar in the smallest window and then had pay more for the window

Jul 24, 2009 | 1998 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

78289 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14405 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides