Question about 2004 Honda Accord 2.4

1 Answer

2004 honda accord camshaft bolt specs on 2.4l vtec

Camshaft bolts specs

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 14,585 Answers

42 inch pounds. Start at the middle of the cam/s and work your way out. You don't have to, but I start by snugging the bolts up (no order. Then toque them down. Then double check, starting at the middle again.

Posted on Dec 09, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am trying to find out the torque spec for a 1999 honda accord 3.2 vtec connecting rod and main bearing


From Helms manual (factory shop manual)
Rod, FI engine: 34 lbs
Rod, Carb engine: 23 lbs
(I use blue thread locker on rod caps)


Crank caps: 51 lbs. (oil threads and under bolt head)

Mar 05, 2015 | 1999 Honda Accord

1 Answer

Replacing alternator on honda accord vtec


unplug the batterie ..the connector of starter and is bolt..put the new one in and reassemble all part in reverse order

Apr 20, 2012 | Cars & Trucks

2 Answers

Head torque specs for 92 honda accord with f22a1


Thanks for using FixYa.

To install:
  1. Install a new head gasket on the engine, making certain it is positioned correctly. The cylinder head dowel pins and the oil jet must be in place. Refer to the illustrations if necessary.
  2. Install the head. Lower it straight down onto the block, aligning it correctly.
  3. Apply clean engine oil to the bolt threads and the contact face of the bolt head. Install the head bolts finger-tight.
  4. On all models except 1988-89 DOHC Prelude and 1992-95 Preludes with 2.3L and VTEC engines, tighten the head bolts following sequence A. On 1988-89 DOHC Preludes, use sequence B. Use sequence C on 1992-95 Preludes with 2.3L and VTEC engines.
    1. On 1984-89 Accords and 1984-91 Preludes, tighten the bolts in two passes. The first pass should bring the bolts to about 22 ft. lbs. (30 Nm). On the second pass, tighten the bolts to their final torque of 49 ft. lbs. (68 Nm).
    2. On 1990-93 Accords, tighten the bolts to 29 ft. lbs. (40 Nm) on the first pass, 51 ft. lbs. (70 Nm) on the second pass, then tighten the bolts to their final torque of 78 ft. lbs. (108 Nm).
    3. On 1994-95 Accords and 1992-95 Preludes, the bolts are also tightened in three passes. Tighten the bolts to 29 ft. lbs. (40 Nm) on the first pass, 51 ft. lbs. (70 Nm) on the second pass, then tighten the bolts to their final torque of 72 ft. lbs. (100 Nm).

      0900c152800b80b4.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Fig. 9: Cylinder head bolt torque sequence A

      jturcotte_2331.gif

      Fig. Fig. 10: Cylinder head bolt torque sequence B


      0900c152800b80b6.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Fig. 11: Cylinder head bolt torque sequence C


  5. If applicable, assemble the intake and exhaust manifolds to the head. Use new gaskets.
  6. If applicable, install the cam, rockers and camshaft holders.
  7. If equipped, install the EGR crossover and air suction pipes.
  8. Connect the exhaust pipe to the manifold using new nuts.
  9. Install the timing belt.
  10. Install the valve cover.
  11. Install the cylinder sensor (if equipped) and the distributor.
  12. If applicable, install the alternator.
  13. Install the power steering pump, then connect the inlet hose to the pump.
  14. Install the accessory drive belts. Adjust the belt tensions.
  15. Install the heater hoses.
  16. Install the cruise control actuator if it was removed.
  17. Connect the spark plug wires. Connect all the wire harnesses and vacuum hoses to the cylinder head, intake manifold and throttle body/carburetor.
  18. Connect the throttle control cable and/or accelerator cable at the throttle body.
  19. Connect the fuel lines.
  20. Install the brake booster, PCV and charcoal canister vacuum hoses.
  21. Install the air cleaner and intake duct.
  22. Refill the engine coolant. It is recommended that the engine oil be changed whenever a cylinder head is removed.
  23. Connect the negative battery cable.
  24. Start the engine, allowing it to idle. Bleed the cooling system. Check the work area carefully for any signs of fluid leakage or any indication of the timing belt rubbing or slapping the covers.

Sep 25, 2011 | Honda Accord Cars & Trucks

1 Answer

2000 honda civic sir 1.6 dual cam vtec head torque and head bolt location


The Head bolts are located below the cams, so you have to take the cams out to get to the bolts.
The torque specs for the head bolts in sequence is 20, 40, then end at 63ft lbs. Be sure to apply anti sieze or dip the head bolts in oil, before you torque them down or you might pull out the threads. (Not a good thing TRUST ME!)
Hope this helps.

Aug 10, 2010 | 2000 Honda Civic

2 Answers

Torque for 1995 honda accord camshaft bolts on a 2.2, 4 cylinder engine


camshaft sprocket bolt torque is 27 ft lbs. the camshaft bearing bolts torque is 9 ft lbs.tighten each bearing cap gradually to prevent binding.your rocker arm bolts torque 6mm bolts to 9 ft lbs and the 8mm bolts to 16 ft lbs.

Nov 23, 2009 | 1995 Honda Accord

4 Answers

Torque specs for 96 Honda Accord 2.2L


the main bearings bolts is to 1st step 30Nm or 22lbs ft and the last step is 75Nm or 54lbs ft in this tighten secuence. 9 3 1 5 7 on the top bolts and........ ........ ........ ... 8 6 2 4 10 botton bolts and the connecting rod 45Nm or 34 lbs ft i hope be help you

Nov 09, 2009 | 1996 Honda Accord

1 Answer

Head bolt torque specs for 200 honda accord 3.0


its a three step process 1st 29ft/lbs 2nd 51ft/lbs 3rd 72.3ft/lbs

Oct 08, 2009 | 1993 Honda Accord

2 Answers

Which engine fits a del sol honda 1993


Anything that is OBD 1 or newer if you want it to be legal, here are the most common options and the basic requirements. 1. B16A2/3: Completely bolt-in Swap, VTEC needs to be wired, SIR II, Hasport shift linkage. Del Sol VTEC for the del sol 2. B18B: Completely bolt-in swap, SIR II, Hasport shift linkage. Del Sol VTEC for the del sol 3. B17A: Completely bolt-in swap, cable-hydro transmission kit(not recommended) or hydraulic b-series transmission, VTEC needs to be wired. 4. B18C1: Completely bolt-in swap, VTEC needs to be wired. 5. B18C5: Completely bolt-in swap, OBD conversion, VTEC needs to be wired. 6. B16B: Completely bolt-in swap, OBD conversion, VTEC needs to be wired. 7. H22A: Mount kit required, Hasport shift linkage, VTEC needs to be wired. 8. B16A: Not recommended! Too much work, more costly compared to B16A2/3's. 9. D16Z6: Completely bolt in, VTEC needs to be wired. 10. D16Y8: Completely bolt in, VTEC needs to be wired. If you want to know more check this out - http://hondaswap.com/swap-articles/en gine-swaps-101-a-29052/

May 18, 2008 | 1995 Honda Civic del sol

Not finding what you are looking for?
2004 Honda Accord 2.4 Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...