Question about Cars & Trucks

1 Answer

Removal of the turn signal assembly. - Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Cars & Trucks Expert
  • 337 Answers

On what?

Posted on Dec 08, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn signal not working but hazard working. Switch good, flasher relay good.


if all fuses are good and your satisfied the flasher is good the turn signal assembly may be bad. this is the the arm your pushing down to make the turn signals work. its an assembly and may require removal of the steering wheel to replace. hope this helps

Feb 05, 2011 | Nissan Sentra Cars & Trucks

1 Answer

2007 toyota solara high beam doesn't work, fuses, bulbs and low beam are fine. Could it be a defective switch or sensor?


Hi, the likely problem is the combination switch/wand. The part costs $83 at autozone, but you may want to shop around. Instructions are pasted below the diagram. Please let me know if you have questions, and thanks for using FixYa.

jturcotte_627.gif


Removal & Installation

  1. Remove 3 screws and steering column cover
  2. Disconnect the connector.
  3. Release the claw and pull out the turn signal switch assembly.

    jturcotte_628.gif

Fig. Removal and installation of the turn signal switch



To install:

  1. Install the switch assembly.
  2. Connect the electrical connection.
  3. Replace the three screws in the steering column cover.

Dec 27, 2010 | 2001 Toyota Camry Solara

1 Answer

How to change a front turn light in a 1996 taurus.


Lamps, Parking Front Lamp-Lamp Assembly, Taurus
Removal and Installation
  1. Remove Headlamp (13008) as outlined.
Headlamp Assembly
Removal and Installation
  1. ani_caut.gif WARNING: THE REPLACEABLE HALOGEN HEADLAMP BULB CONTAINS GAS UNDER PRESSURE. THE HALOGEN HEADLAMP BULB MAY SHATTER IF THE GLASS ENVELOPE IS SCRATCHED OR THE HALOGEN HEADLAMP BULB IS DROPPED. HANDLE HALOGEN HEADLAMP BULB CAREFULLY. GRASP HALOGEN HEADLAMP BULB ONLY BY ITS PLASTIC BASE. AVOID TOUCHING GLASS ENVELOPE. KEEP HALOGEN HEADLAMP BULB OUT OF REACH OF CHILDREN.
    Position headlamp switch (11654) and headlamp time delay switch (13736) in the OFF position.
  1. Remove two bolts retaining headlamp (13008) to upper support assembly and loosen pinch bolt. Remove headlamp assembly from vehicle.
  1. Remove park lamp bulb and socket (Sable only) and headlamp bulb and socket from Headlamp Assembly as outlined.


    Headlamp Assembly (Taurus Shown, Sable Similar)


    k24744a.gif
  1. Turn lamp socket and wiring (13410) assembly 1/2 turn counterclockwise and remove from parking lamp (13200) housing.
  1. Remove screw from park/turn signal housing.
  1. Using 1/4 inch drive socket extension and swivel, insert tool through two access holes in upper radiator support. Remove screws from park/turn signal housing.
  1. Remove parking lamp from vehicle.
  1. To install, reverse Removal procedure.


    Front Lamp-Lamp Assembly, Taurus


    k23818a.gif

Nov 19, 2010 | Ford Taurus Cars & Trucks

1 Answer

Removing and reinstalling a new headlight assembly in a 95 jeep grand cheerokee


LIGHTING Headlights REMOVAL & INSTALLATION Cherokee, Wagoneer and Comanche Models Fig. 1: Remove the top corner headlight bezel mounting screw 91076p12.jpg
Fig. 2: To access the turn signal bulb or headlight bezel mounting screws, remove the 2 turn signal housing retaining screws 91076p13.jpg
Fig. 3: After removing the turn signal housing from the headlight bezel, remove the 2 bezel mounting screws . . . 91076p27.jpg
Fig. 4: . . . then carefully pull the headlight bezel away from the headlight assembly 91076p11.jpg
Fig. 5: Remove the 4 headlight assembly retaining ring screws . . . 91076p07.jpg
Fig. 6: . . . then pull the retaining ring off of the headlight assembly 91076p06.jpg
Fig. 7: Pull the headlight assembly away from the vehicle just far enough to disengage the electrical connector from behind the headlight 91076p28.jpg
  1. Remove the headlamp bezel and retaining ring attaching screws. Remove the bezel and retaining ring.
  2. Pull the headlight out, disconnect the wire harness and remove the headlight from the vehicle.
  3. Install the headlight in the reverse order of removal.
Grand Cherokee and Grand Wagoneer Models
  1. Open the hood, reach into the engine compartment and locate the lock ring supporting the bulb assembly.
  2. Rotate the lock ring 1?8 turn counterclockwise and pull the bulb straight out from the housing. To install:
  3. Install a new bulb and position the bulb assembly in the lamp housing.
  4. Rotate the lock ring 1?8 turn clockwise to secure.
----
The Grand Cherokee will have an assembly that is fastened with bolts and screws to the body.
Get the new assembly and compare to the old one to see where to unfasten the bolts and other fasteners to aid in removing quickly.

Oct 08, 2010 | 1995 Jeep Grand Cherokee

1 Answer

How to replace the ignition on a 1991 oldsmobile cutlass cierra


If you mean the ignition lock cylinder:

Ignition Lock Cylinder CAUTION
If the car is equipped with an air bag, do not service the steering column or dashboard components. Extreme danger of air bag deployment exists even with the battery removed! Serious injury could occur. REMOVAL & INSTALLATION Without Air Bag
  1. Place the ignition switch in the RUN position.
  2. Remove the lockplate, turn signal switch and buzzer switch.
  3. Remove the screw and lock cylinder. NOTE: If the screw is dropped on removal, it could fall into the column, requiring complete disassembly to retrieve the screw. To install:
  4. Rotate the cylinder clockwise to align cylinder key with the keyway in the housing.
  5. Push the lock all the way in.
  6. Install the screw. Tighten the screw to 14 inch lbs. (2 Nm) for adjustable columns and 25 inch lbs. (3 Nm) for standard columns.
With Air Bag CAUTION
Before proceeding, refer to Section 6 for information on disabling and enabling the SIR (air bag) system; otherwise, serious injury could occur.
  1. Turn the steering wheel so the vehicles wheels are pointed straight ahead.
  2. Place the ignition switch into the LOCK position to prevent undercentering of the coil assembly.
  3. Disable the SIR system. Disconnect the negative battery cable.
  4. Remove the coil assembly retaining ring, then disconnect the inflatable restraint coil assembly. Let the switch hang freely if removal is not needed. To remove the coil assembly proceed.
  5. Remove the wave washer, then the shaft retaining lock ring with tool J-23653-SIR to push down on the shaft lock. Dispose of the ring, it is not reusable. Fig. 1: Special tool J-23653-SIR or equivalent is required for pushing down the shaft lock to remove the shaft ring 86818085.gif
  6. Remove the shaft lock, then disconnect the canceling cam assembly.
  7. Remove the upper bearing spring, race seat and race.
  8. Position the turn signal to the right turn (up) position.
  9. Remove the multi-function lever and hazard knob assembly. Unfasten the round washer head screw and signal switch arm, along with the turn signal switch screws.
  10. Remove the turn signal switch assembly by unfastening the connector from the bulkhead connector. Gently pull on the harness through the column and disconnect.
  11. Make sure the coil assembly does not become uncentered, this could happen if the centering spring is pushed down letting the hub rotate while the coil is removed from the steering column.
  12. Remove the inflatable restraint coil assembly with the wiring harness from the column assembly.
  13. Remove the wire protector, then attach a length of mechanics wire to the coil terminal connector to aid in reassembly. Then gently pull the wire through the column.
  14. Remove the key from the steering column lock cylinder set, then remove the buzzer switch assembly.
  15. Reinsert the key into the lock cylinder, turn it to the LOCK position.
  16. Remove the lock retaining screw, then the cylinder. To install: NOTE: Make sure all fasteners are securely seated before applying the necessary torque. If you fail to do so, component damage or malfunctioning of the steering column may occur.
  17. Install the lock cylinder assembly, insert the retaining screw, then tighten to 22 inch lbs. (2.5 Nm).
  18. Insert the key into the lock cylinder. Install the buzzer switch assembly. Turn the key to the LOCK position.
  19. Install the turn signal switch assembly wiring harness through the column, let the switch hang freely. Connect the wiring to the bulkhead.
  20. Insert the coil assembly wiring harness through the column letting the coil hang freely. Attach the turn signal assembly with the binding head screws. Tighten the screws to 30 inch lbs. (3 Nm).
  21. Attach the signal switch arm with the round washer head screw, tighten the screw to 20 inch lbs. (2 Nm).
  22. Install the hazard knob assembly and the multi-function lever.
  23. Install the inner race, upper bearing race seat and spring. Attach the turn signal cancelling cam assembly, apply grease for lubrication.
  24. Replace the shaft lock and install a new shaft lock retaining ring. Use tool J-23653–SIR or equivalent to push down on the shaft lock. The ring must be firmly seated in the groove on the shaft. NOTE: Set the steering shaft so that the block tooth on the race and upper shaft is at the 12 o'clock position. The wheel on the car should be straight ahead. Set the ignition switch to the LOCK position, as this will ensure no damage to the coil assembly.
  25. Install the wave washer, then attach the coil assembly, make sure it is centered correctly. Fig. 2: Centering the coil assembly is important in assembling the column assembly 86818086.gif

  26. Attach the coil assembly retaining ring, the ring must be firmly seated in the groove on the shaft.
  27. Gently pull the lower coil assembly, turn signal, and pivot (pulse) wires to remove any kinks that may be inside the steering column assembly. If you fail to do this you can damage the wiring.
  28. Complete assembling the steering column assembly.
  29. Attach the negative battery cable.
  30. Check the functions of the turn signal, make sure it cancels when turned on and the steering wheel is turned.
  31. Enable the SIR system. prev.gif next.gif

Aug 01, 2010 | 1991 Oldsmobile Cutlass Ciera

1 Answer

Rear turn signal how to change bulb


open the liftgate remove the screws holding the tail,stop,turn signal and back-up light assembly to the rear door opening. seperate the light assembly from the vehicle body. disengaging the hook holding the outer end of the light assembly to the body. swing the housing out to access the bulb holders. rotate bulb holder and remove blown out bulb. installation is the reverse of removal. hope this will help!!!

Apr 03, 2010 | 2005 Dodge Grand Caravan

1 Answer

How to change the right front turn indicator bulb on 2004 excursion


1. Remove the front turn signal assembly mounting screws and slide the assembly forward, out of the vehicle body.

2.Twist the bulb socket a quarter turn counterclockwise, then remove the bulb assembly from the housing

3.The defective bulb can then be removed from the socket and replaced.

4. Installation of the front turn signal assembly is the reverse of removal.

Jan 21, 2010 | 2000 Ford Excursion

1 Answer

How to change the right front turn indicator on


1.Remove the front turn signal assembly mounting screws and slide the assembly forward, out of the vehicle body.
2.Twist the bulb socket a quarter turn counterclockwise, then remove the bulb assembly from the housing
3.The defective bulb can then be removed from the socket and replaced.
4. Installation of the front turn signal assembly is the reverse of removal.

Dec 31, 2009 | 2000 Ford Excursion

1 Answer

HOW DO YOU REMOVE THE HEADLIGHT ASSY TO REPLACE THE TURN SIGNAL BULB


SECTION 417-01: Exterior Lighting 2001 Escape Workshop Manual REMOVAL AND INSTALLATION Side Lamp/Front Turn Signal Lamp Bulb Removal and Installation
  1. Remove the wheel and tire. For additional information, refer to Section 204-04 .
  1. Position the inner fender well aside.
    1. Remove the bolts.
    1. Remove the pin-type retainers.
    1. Remove the screw.
    1. Position the inner fender well aside.
  2. Remove the lamp socket from the lamp assembly.
  3. Remove the bulb.

06a0ca1.gif

Dec 01, 2009 | 2001 Ford Escape

1 Answer

Replace signal light switch


Turn signal light switch is part of an assembly that includes the wiper switch, and hazard flasher (I believe Suzuki name is head switch assembly). It requires removal of steering wheel with puller, and also proper care/ procedure to temporarily disable air bag (air bag is explosive device).

Jul 29, 2009 | 1995 Geo Metro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...