Question about Isuzu Cars & Trucks

2 Answers

Where is the cold start valve or injector located on a 1998 isuzu hombre pickup?

Truck was running. started to sputter. put in gas and sea foam. getting plentyn of fuel to the fuel rail. fuel pump has plkenty of pressure. truck turns over but won't ncrank.

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Isuzu Master
  • 14,585 Answers

Check for spark to the plugs. If you don't have it, look at the crankshaft position sensor. If you do, then look at replacing the fuel filter. Clogged filters will give you pressure. But not volume. I would replace it anyway.

Posted on Dec 09, 2014

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 96 Answers

There is no cold-start injector on that vehicle.

Posted on Dec 09, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

My checck engine light is blinking it came on 2 months ago i was told i neede a map sensor or cat convertor light is now blinking and car has hessitation


buy a can of sea foam motor treatment at a auto parts store pour it in the gas tank with at least a half tank of gas disconnect the negative battery terminal for about 15 seconds reconnect, than start car and drive it should solve problem with hesitation if the problem comes back check for a bad injector are fouled spark plug, you should put sea foam or other brands of injector cleaner fuel conditioner in your gas every other fill up ethanol gas fouls plugs and causes injectors to clog because of the carbon that it forms on your pistons valves and intake runners, sea foam will cure this problem

Feb 24, 2015 | 2001 Mazda Protege

1 Answer

Location of cold start injector on 1998 isuzu hombre


Not sure on yours (read a shop manual) but most are located low on intake below the throttle body.

Dec 08, 2014 | Isuzu Cars & Trucks

2 Answers

Sometimes it startes but runs rough lacks power for a bit and blows black smoke


over fuel from bad needle and seat , or leaking injector seals you didn't mention make model year or type of equipment so that answer is the best you get

Dec 03, 2017 | 2001 Chrysler Town & Country

1 Answer

Sputters and dies on cold start, significant drop in gas mileage.


You need to rebuild the carburetor or clean the choke linkage and make sure the choke valve closes cold.

Nov 12, 2013 | 1985 Isuzu Pickup

2 Answers

1998 isuzu hombre will not start after it rains


is it distributer or coil pack style if so id check into them either one could be getting wet

Dec 05, 2012 | 1998 Isuzu Hombre

1 Answer

I have a 1998 isuzu hombre pickup and early mornings or when the engine is cool the engine cranks right up but it seems when the engine gets hot it will turn over several times before cranking and when it...


usually a temp sensor on its way out. engine thinks it has cold air coming in so adjusts for that. but when warm air comes in the engine uses more fuel than it needs so will take longer to start. could also be the maf is dirty and needs cleaning as same as the MAP sensor, when replacing a dirty air filter its best to clean these parts as the muck that has been able to get through the filter will coat them with muck. this changes the sensors readings can become lower or high depending on the condition or evaporation in the air.

Feb 04, 2018 | 1998 Isuzu Hombre

2 Answers

Pickup park for three years running owner went over seas afgan. What to do before starting with old gasoline.


Add fresh gas and a can of Sea Foam, charge the battery, check the brakes if you plan on driving it do these things and you should be good to go.

Sep 09, 2011 | 1989 Isuzu Pickup 2WD

1 Answer

When u go to take off from a stop it dies


Run a can of Sea Foam injector cleaner through your fuel system.

Mar 18, 2010 | 1998 Ford Escort

2 Answers

Crankshaft position sensor on a 1996 isuzu hombre


should be between the crank dampener and the block, i mean they are all relatively the same on all cars should be the only wires running close to the crank dampener

Dec 11, 2008 | 1996 Isuzu Hombre

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14411 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...