Question about Dodge Ram 1500

1 Answer

How do I do a full key down sequence on a 2003 ram 1500.

Left key in ignition over night and anti-theft program turned on. Locked out everything.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 127 Answers

You Don't Instead You Replace The Car You Have With A KIA Sedona With A 10 Year Warrenty! The Car You Have Is A Piece Of Junk!

Posted on Dec 08, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I reset the ProLock system?


Hi Carol , do you mean PATS passive antitheft system ? Locked up your car ,do you mean it won't crank over an start ?
The passive anti-theft system uses radio frequency identification technology to deter a driveaway theft. Passive means that it does not require any activity from the user.
  • During each vehicle start sequence, the ignition key identification code is requested by the vehicle protection anti-theft electronics.
  • If the key's ID code has been programmed into the system, the powertrain control module (PCM) (12A650) is signaled to enable the vehicle to start.
  • If the key's ID code is not programmed into the system, or if no encoded key is detected, then the powertrain control module is signaled to disable the vehicle.
The passive anti-theft system communicates the state of the security system to the powertrain control module via the J-1850 communications network data link connector (DLC). The powertrain control modulebased on the communications from the passive anti-theft system, will determine if the vehicle's engine is enabled to start. The passive anti-theft system differs from the active anti-theft alarm system in that the passive anti-theft system enables/disables the vehicle from starting and only operates with the ignition switch in RUN/START position. The active anti-theft alarm system has perimeter protection capabilities and operates only with the ignition switch OFF. Refer to Section 13-11A for active anti-theft alarm system information.
Vehicle Disabling The passive anti-theft system will be activated and disable the vehicle from starting if any of the following conditions exist:
  • damaged encoded key
  • unprogrammed key
  • non-encoded key (key has no electronics)
  • wiring concern
  • transceiver concern
  • Passive Anti-Theft System (PATS) control module concern
  • J-1850 Communications Network concern
  • Powertrain Control Module (PCM)

Apr 15, 2015 | 1995 Ford Taurus

1 Answer

Lost ignition key 2009 Dodge Ram 1500


I doubt it.
With the key in lock position the shifter should be locked and the steering wheel will lock as soon as you turn it.
You would need to power several of the circuits including the wire going to the starter.
Did the truck have an alarm / anti-theft system ?

Jul 01, 2012 | 2009 Dodge Ram Pickup 1500

3 Answers

How do you reset anti theft on a 2007 equinox


TURN ON IGNITION SWITCH TO ON POSITION.ENGINE OFF.REPEATEDLY PRESS VECHICLE INFORMATION BUTTON UNTIL PRESS TO RELEARN REMOTE KEY IS DISPLAYED.PRESS SET RESET BUTTON UNTIL REMOTE KEY LEARNING ACTIVE IS DISPLAYED. IF THAT PROCEDURE DONT WORK.INSERT MASTER KEY INTO IGNITION SWITCH.NOW SWITCH IGNITION ON SWITCH IGNITION OFF.REMOVE MASTER KEY.WITHIN 10 SECONDS INSERT NEW KEY.SWITCH IGNITION ON.ENSURE SYSTEM WARNING LAMP SWITCHES OFF.NEW KEY NOW PROGRAMMED.IF YOU STILL HAVING PROBLEM RESETING THEFT SECURITY SYSTEM THE DEALERSHIP HAS TO FIX.REPROGRAM IT.

Mar 14, 2011 | 2007 Chevrolet Equinox LS New Cars

1 Answer

Wont turn over antitheft device preventing car from starting only have 1 key and it is the orriginal what do i do


close the doors. Put your Master Key in the door. turn it to the 1st position right, then 2nd position right, then 3rd position left. this will reset the starter immobilization sequence which is part of the anti theft system monitored by the EWS system. then put the key in the ignition and fire it up try this

Sep 12, 2010 | 2003 BMW 325

1 Answer

Hi. I have a 2003 ford windstar with ford anti theft. While driving ,the engine just stopped and the anti theft symbol on the dash kept flashing,and the engine will not turn over.I disconnected the...


you will have to take your vehicle to the nearest dealer the theft system is the issue most likley you will have to replace the ignition switch but you will have to get it properly diagnost do yourself a favor and save u time and money

Nov 27, 2009 | 2003 Ford Windstar

1 Answer

Reprogam alarms & key less entry


SECTION 419-01A: Anti-Theft — Perimeter 2002 Explorer/Mountaineer Workshop Manual DESCRIPTION AND OPERATION Anti-Theft —Perimeter The perimeter anti-theft system consists of the following:
  • driver door disarm switch
  • vehicle security module
  • keyless entry remote transmitter
  • door ajar switches
  • liftgate ajar switch
  • liftgate glass ajar switch
  • hood ajar switch
------------------------------------------------------------------------------------
Anti-Theft —Passive The passive anti-theft system (PATS) contains the following components:
  • theft indicator
  • encoded ignition key
  • PATS transceiver module
  • powertrain control module (PCM)
  • standard corporate protocol (SCP) communication network
Principles of Operation
The PATS uses a specially encoded ignition key. Each encoded ignition key contains a permanently installed electronic device called a transponder. Each transponder contains a unique electronic identification code out of over 18 billion, billion combinations.
The passive anti-theft system (PATS), also known as SecuriLock ®, uses radio frequency identification technology to deter a drive-away theft. This system is known as SecuriLock® in North America, Safeguard® in the U.K., and PATS in Continental Europe. Passive means that it does not require any activity from the user.
The SecuriLock® System (PATS) is not compatible with aftermarket remote start systems, which allow the vehicle to be started from outside the vehicle. These systems may reduce the vehicle security level, and also may cause no-start issues. If equipped the remote start system must be removed before investigation of PATS-related, no-start issues.
Each encoded ignition key must be programmed into the vehicle's powertrain control (PCM) before it can be used to start the engine. There are special diagnostic repair procedures described in this section that must be carried out if a new encoded ignition key is necessary.
This system contains a new feature named Unlimited Key Mode. This feature allows a customer to program more than eight keys to the vehicle if they request it. Each vehicle in Unlimited Key Mode is set up with a special Unlimited Transponder Security Key. This allows all the customer vehicles to share the same keys, but no other keys from outside can be used to operate the vehicles. For an individual customer, any randomly selected Security Key is acceptable. Refer to Unlimited Key Mode Programming in Key Programming Switch State Control in this section.
The PATS transceiver module communicates with the encoded ignition key. The module is located behind the steering column shroud and contains an antenna connected to a small electronics module. During each vehicle start sequence, the transceiver module reads the encoded ignition key identification code and sends data to the PCM.
The control functions are contained in the PCM. This module carries out all of the PATS functions, such as receiving the identification code from the encoded ignition key and controlling the engine enable. The PCM initiates the key interrogation sequence when the vehicle ignition switch is turned to RUN or START.
All elements of the PATS must be functional before the engine is allowed to start. If any of the components are not working correctly, the vehicle will not start.
The PATS uses a visual theft indicator. The indicator will prove out for three seconds when the ignition switch is turned to RUN or START under normal operation. If there is a PATS concern, this indicator will either flash rapidly or glow steadily when the ignition switch is turned to RUN or START. The PATS system also flashes the theft indicator every two seconds at ignition OFF to act as a visual deterrent.
The PATS will be activated and will disable the vehicle from starting if there is a:
  • incorrectly encoded ignition key
  • damaged encoded ignition key
  • unprogrammed key
  • non-encoded key (key has no electronics)
  • damaged wiring
  • damaged transceiver
  • damaged PCM
Inspection and Verification
  1. Verify the customer concern by operating the system.
  1. Visually inspect for obvious signs of mechanical and electrical damage.
-------------
Key Programming Using Two Programmed Keys NOTE: This procedure only works if two or more programmed ignition keys are available and it is desired to program additional key(s). If two keys are not available, follow the procedure in Key Programming Using Diagnostic Equipment in this section.
NOTE: PID SPARE_KY must be enabled for this procedure to operate. If this PID is not enabled, follow the security access procedure above and select SPARE KEY PROGRAMMING SWITCH: ENABLED.
NOTE: If the programming procedure is successful, the new key(s) will start the vehicle and the THEFT indicator will illuminate for approximately three seconds.
NOTE: If the programming procedure is not successful, the new key(s) will not start the vehicle and the THEFT indicator will flash. If the programming procedure was not successful leave the ignition switch in the RUN position for at least 30 seconds then repeat the key programming procedure from Step 1. If the failure repeats, refer to Diagnosis and Testing to review the DTCs and carry out pinpoint tests as necessary.
NOTE: A maximum of eight ignition keys can be programmed to a passive anti-theft system (PATS) equipped vehicle. If more are needed, refer to Key Programming Switch State Control in this section.
NOTE: If the steps are not carried out as described, the programming procedure will end.
NOTE: Ignition keys must have correct mechanical key cut for the vehicle and must be a PATS encoded key.
NOTE: If the vehicle is in unlimited key mode, this spare programming procedure still functions. Any two keys that can start the vehicle may be used to program in an additional unlimited key.
  1. Insert the first programmed ignition key into the ignition lock cylinder and turn the ignition switch from OFF to RUN (maintain the ignition switch in RUN for three seconds).
  1. Turn the ignition switch to OFF and remove the first key from the ignition lock cylinder.
  1. Within seconds of turning the ignition switch to OFF, insert the second programmed ignition key into the ignition lock cylinder and turn the ignition switch from OFF to RUN (maintain the ignition switch in RUN for three seconds).
  1. Turn the ignition switch to OFF and remove the second key from the ignition lock cylinder.
  1. Within 20 seconds of turning the ignition lock cylinder to OFF, insert the unprogrammed ignition key (new key) into the ignition lock cylinder and turn the ignition switch from OFF to RUN (attempt to start the vehicle).
  1. If it is desired to program additional key(s), repeat the key programming procedure from the beginning.
-------------------------------------------------------------------------------------
NOTE: The security access procedure is utilized to obtain passive anti-theft system (PATS) security access. PATS security access must be granted to erase ignition keys, enable/disable unlimited key mode, and enable/disable the spare key programming switch (PID SPARE_KEY). The security access procedure invokes an inherent 10 minute time delay prior to granting security access during which the diagnostic tool must remain connected to the vehicle. Once security access has been granted, a security access command menu is displayed which offers various command options. (For additional information, refer to Powertrain Control Module (PCM) Configuration Command Index).
NOTE: Once security access has been granted, multiple security access commands should be executed (if necessary) prior to exiting the command menu. This avoids the carrying out of an additional security access procedure and the associated 10 minute time delay.
  1. From the diagnostic tool Ford Service Function (FSF) card, enter PCM. Select SECURITY ACCESS. This procedure will take 10 minutes to carry out, during which the ignition switch must be in RUN and the diagnostic tool must be connected to the vehicle.
  1. After the 10 minute security access procedure has been completed, a new menu will be displayed with command options. Select only those functions necessary before exiting out of this menu. Once exited out of this menu, the security access procedure must be repeated again to carry out additional commands.

Oct 01, 2009 | 2002 Mercury Mountaineer

1 Answer

98 explorer will turn over but not start


Yes you have a problem with the theft system. Have you tried a different key? It has a transponder system.

Aug 22, 2009 | 1998 Ford Explorer

1 Answer

2003 ford winstar only key broke in the ignition so i replace the the ignition and reprogramed brainbox however vehicle anti theft light keeps blinking when vehicle is on and off


the anti-theft light is supposed to blink when the car is locked to show the system is armed.

Does it flash while driving?

Principles of Operation
The PATS uses a specially encoded ignition key. Each encoded ignition key contains a permanently installed electronic device called a transponder. Each transponder contains a unique electronic identification code out of over 18 billion, billion combinations.
The passive anti-theft system (PATS), also known as SecuriLock ®, uses radio frequency identification technology to deter a driveaway theft. This system is known as Securilock® in North America, Safeguard® in the U.K., and PATS in Continental Europe. Passive means that it does not require any activity from the user.
The SecuriLock® System (PATS) is not compatible with aftermarket remote start systems, which allow the vehicle to be started from outside the vehicle. These systems may reduce the vehicle security level, and also may cause no-start issues. If equipped the remote start system must be removed before investigation of PATS-related, no-start issues.
Each encoded ignition key must be programmed into the vehicle's powertrain electronic control (PCM) before it can be used to start the engine. There are special diagnostic repair procedures described in this section that must be carried out if a new encoded ignition key is necessary.
This system contains a new feature named Unlimited Key Mode. This feature allows a customer to program more than eight keys to the vehicle if they request it. Each vehicle in Unlimited Key Mode is set up with a special Unlimited Transponder Security Key. This allows all the customer vehicles to share the same keys, but no other keys from outside can be used to operate the vehicles. For an individual customer, any randomly selected Security Key is acceptable. Refer to Unlimited Key Mode Programming in Key Programming Switch State Control in this section.
The PATS transceiver module communicates with the encoded ignition key. The module is located behind the steering column shroud and contains an antenna connected to a small electronics module. During each vehicle start sequence, the transceiver module reads the encoded ignition key identification code and sends data to the PCM.
The control functions are contained in the PCM. This module carries out all of the PATS functions, such as receiving the identification code from the encoded ignition key and controlling the engine enable. The PCM initiates the key interrogation sequence when the vehicle ignition switch is turned to RUN or START.
All elements of the PATS must be functional before the engine is allowed to start. If any of the components are not working correctly, the vehicle will not start.
The PATS uses a visual theft indicator. The indicator will prove out for three seconds when the ignition switch is turned to RUN or START under normal operation. If there is a PATS concern, this indicator will either flash rapidly or glow steadily when the ignition switch is turned to RUN or START. The PATS system also flashes the theft indicator every two seconds at ignition OFF to act as a visual deterrent.
The following will activate the PATS and will disable the vehicle from starting:
  • incorrectly encoded ignition key
  • damaged encoded ignition key
  • unprogrammed key
  • non-encoded key (key has no electronics)
  • damaged wiring
  • damaged transceiver
  • damaged PCM

May 26, 2009 | 2003 Ford Windstar

1 Answer

Problem with starting my 2003 dodge ram


My father has the same problem with his 2001 Chrysler Sebring, the key will go into the ignition switch but wont turn. Called the dealer and seems the tumblers inside the ignition have gotten stuck, the solution... put the key in the ignition and tap it gently with a hammer (plastic tip if you have it) and it worked fine. Not sure what the guys at Autozone are pull but on a Ram 5.7 Hemi there are individual coils, not one, I should know I also have a 2003 Ram 1500 and have changed the plugs (not fun)... I have a code scanner (Hypertec) and when I've gotten a check engine light I check it with the scanner. Turned out mine had a problem with the air sensor in the intake. $15 part fixed the problems. Good Luck.

Apr 18, 2009 | 2004 Dodge Ram 1500

1 Answer

Problem starting my 2003 dodge ram


no if you took it to autozone obviously you have a good ign coil.im sure you have tried turning the wheel at the same time you turn your key. other than that i would replace the lock cylinder and key.

hope2help shack

Apr 18, 2009 | 2004 Dodge Ram 1500

Not finding what you are looking for?

Open Questions:

Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...