Question about 2007 Nissan X-Trail 2.2D

Open Question

Remove the headlamp assembly from a T30 - not just change a lightbulb!

T30 2004. Remove the entire headlamp assembly.

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: Removal of Headlamp bulb?

The Xterra doesn't have stock xenon headlights, so are your lights aftermarket? If not, there is a retaining ring on the back of the headlight housing (under the hood) and you just turn the ring counter clockwise to detach and the the bulb comes right out. Installation is the reverse of removal.

Posted on Nov 24, 2008

michigan man
  • 3533 Answers

SOURCE: Can not get the headlamps adjusted properly.

it is very possible because there is springs on the back of some assemblies and it is very possible the spring is off
I always adjust my headlights at night while facing the side of a building or a glass window that way you know you have them both the same but if you do it in the day time all you need is a small lever to get them both the same

Posted on Feb 06, 2009

  • 2 Answers

SOURCE: Change bulb in front headlamp

Yes you do have to remove the bumper, there are 2 screws underneath the assembly which the bumper obstructs. Once you get to this point it is pretty straight forward.

Posted on Jun 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do change low beam lightbulb on a 2007 dodge ram 1500


Removal & Installation-Get at it from behind the lens assembly.
These instructions show how to remove and replace the whole light assembly but shows a diagram
on what it looks like.

To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following: dod_ram15_02-04_headlmp.gif

    • Negative battery cable
    • Push pins
    • Bolts connecting headlamp unit to fender
    • Bulb sockets from headlamp unit
    • Headlamp unit
To Install:
  1. Install or connect the following:
    • Bulb sockets
    • Headlamp unit to fender with the bolts
    • Seal and push pins
    • Negative battery cable
prev.gif next.gif

Jan 14, 2011 | 2007 Dodge Ram 1500 Quad Cab Sport

1 Answer

How do i change right turn lamp in my 2004 pontiac grand prix


Answer remove the headlight assembly and the bulbs are located below the Assembly to remove headlamp assembly and access signals: -open the hood
-while pushing rearward on the headlamp,pull up half-way on the (white)plastic retaining clip on the electrical connector - align the square cut-out on the retaining clip with the notch on the headlamp
-pull the headlamp assembly straight out from the vehicle (moving the headlamp up and down slightly may help with its removal)
-locate the front turn signal,parking lamp and foglamp bulbs which are located below the headlamp assembly (turn/parking lamp on top and the fog lamp is below it)
-turn the bulb socket 1/4 turn counterclockwise to remove it from assembly
-pull the old bulb from the socket and replace it with a new one
-turn the bulb socket a 1/4 turn clockwise to reinstall it
-reinstall the headlamp assembly carefully so you dont scratch the paint
-push down on (white)plastic retaining clip on the electrical connector while pushing rearward on the headlamp making sure headlamp is secure.

Nov 26, 2009 | 2004 Pontiac Grand Prix

1 Answer

Never changed a bulb


Headlamps -- remove two long bolts with 7 mm or 8 mm hex heads for each headlamp assembly. These bolts are located in the horizontal body panel above and either side of the headlamp assembly. Headlamp can then be pulled forward far enough to remove the lamps from the assembly (twist about a quarter turn).

Taillamps -- inside the trunk, you may have to move the trunk liner aside, but there are three plastic wing nuts holding each taillight assembly in place. After removing these wing nuts, the assembly can be removed.

Sep 25, 2009 | 2002 Dodge Intrepid

3 Answers

Change low beam


Headlamp Removal & Installation Bulb Replacement To Remove:
CAUTION
Halogen bulbs contain pressurized gas. Mishandling a bulb may result in the bulb shattering into flying glass fragments.
CAUTION
Make sure to wear eye protection when handling a halogen bulb.
CAUTION
Do not touch the glass of a halogen bulb, only handle the bulb by the base.
CAUTION
Do not allow a halogen bulb to come into contact with dirt or moisture.
CAUTION
Make sure to dispose of a used halogen bulb properly.
CAUTION
Do not allow children to handle halogen bulbs.
  1. Turn the lamp switch to the off position.
  2. Make sure the bulb is cool before changing.
  3. Remove the headlamp assembly from the headlamp panel.
  4. Remove the rear access cover from the headlamp assembly.
  5. Disconnect the headlamp connector.
  6. Remove the bulb from the headlamp assembly by rotating the bulb and socket counterclockwise.
To Install:
  1. Connect the headlamp connector.
  2. Install the bulb into the headlamp assembly by rotating the bulb and socket clockwise.
  3. Install the rear access cover onto the headlamp assembly.
  4. Install the headlamp assembly into the headlamp panel.

Jul 16, 2009 | 2004 Chevrolet TrailBlazer

1 Answer

Need to change head light on Grand AM


there are two bars on top of each headlamp assembly. pull them out and the entire assembly simply slides out

Jun 13, 2009 | 2004 Pontiac Grand Am

1 Answer

How do you change a front right park light on an audi A4 2003


The easiest way is to remove the headlamp assy.  To do this removed air duct on RH side. remove 2 philips screws and pull up on other end at air filter box.  Next you will see 2 Torx T30 bolts that are holding to headlamp mouting brackets.  remove these completely.  Get a flashlight and look down inside eng bay you will see 2 more mouting points w/ t30 bolts.  loosen but dont entirely remove these.  Slide headlight out.  The park light socket has a big fin style tab grab firmly and twist counter clockwise.  Be sure after removing the bulb that the socket contacts aren't burnt up.  If they are you need a new socket and bulb.  Before reassembling test lights to make sure they work properly and install in reverse order of removal. 

Apr 25, 2009 | 2002 Audi A4

1 Answer

2004 Lincoln Navigator Low Beam Bulb replacement


your owner manual will list the bulb. It is expensive. tascafordparts.com for discount from Ford Dealer

here's 2003, don't have 2004

Navigator high intensity discharge (HID) headlamp
  1. Remove the front radiator air deflector.
  1. Remove the three bolts and the headlamp assembly.
    • Disconnect the electrical connectors.
1c293b4.gif
8. Remove the headlamp bulb protective cover(s).
  • Remove the HID lamp cover.
  • Remove the high beam cover.
  • Disconnect the electrical connector and push the grommet into the headlamp assembly.
7adecf7.gif
  1. Release the spring tabs and remove the HID low beam bulb.
3394a45.gif

Apr 11, 2009 | 2004 Lincoln Navigator

1 Answer

How to replace front turn light bulb on Caddy SRX 2004?


  1. Open the hood.
  2. Remove the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly to flex forward.
  3. Remove the bolt and the push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.
    1. Gently pull the upper fascia and grille assembly forward only far enough to remove the bolt located at the bottom inboard side of the headlamp assembly.
    2. Pull the headlamp assembly straight out to disengage the snap-in retainer at the lower outboard back surface of the assembly. Turn the assembly so that the front inboard corner clears the front fascia.
    3. Pull the headlamp assembly out and away from the vehicle
    4. Disconnect the headlamp electrical connector.
    5. Remove the headlamp assembly from the vehicle.
    6. Remove the headlamp bulb cover from the headlamp assembly.
    7. Remove the headlamp bulb socket from the headlamp assembly.
    8. Remove the headlamp bulb.
    9. Remove the side marker bulb socket from the outer side of the headlamp assembly.
    10. Remove the side marker bulb.

Feb 12, 2009 | 2006 Cadillac SRX

1 Answer

Changing the headlights


This picture shows the rear side of the headlamp assembly. I've circled the access caps to the high & low beam bulbs (they just twist off (counter-clockwise) to access the bulbs. Depending on which engine is in your Tiburon, access is easier if you remove three 10mm mounting bolts to the headlamp assemblies and remove the entire headlamp assemblies (see illustration)
c173c7f.jpg You'll want to disconnect these two connectors .. then remember to reconnect them when you put the assemblies back on.

Hope this helps

Dec 20, 2008 | 2004 Hyundai Tiburon

1 Answer

Headlamp assembly


Remove the 3 10mm bolts from the top outer edges of the assembly. Then slip your fingers under the front edge and pull up while pulling to the front of the car to remove it from the plastic retainer under the assembly. Reinstall in reverse order.

Nov 18, 2008 | 2001 Mitsubishi Eclipse

Not finding what you are looking for?
2007 Nissan X-Trail 2.2D Logo

Related Topics:

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

723 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...