Question about 2002 Mazda Protege

1 Answer

Correct way to install g timingbelt 02 Mazda protege

Posted by on


1 Answer

You get instruction book with the new belt

You look at your factory service manual before you
start any job

You could try the internet or you tube video

Posted on Dec 08, 2014


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: mazda protege fuel pump 02

to take the seat out you have to pull up on it hard. before u start connect the neg. side of the battery. open the gas cap to help to let the or some of the pressure out of the tank.remove the fuel pump cover and unplug the electrical connector and disconnect the wire on top of the fuel pump. disconnect the fuel supply and return hoses from the pump. be careful when trying to unscrew to screws you might have to tip on them to loosing up the lock tight that was put on the screws from the factory. than carefully lift the pump out. disconnect the electrical and move the hose clamp clear the pump fitting. remove the band securing the pump to the bracket and bracket at the bottom of the pump with the rubber mount. remove pump and always remember that gasoline is extremely flammable so take extra precautions when you work on any part of the fuel system. good luck.

Posted on Jan 27, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Window wont go up

Power window repair - Mazdas247 > ... > Mazda Protege Forum > Protege How-To

Aug 8, 2005 - 10 posts - ‎10 authors

I have a 2002 and last week the driver's side power window died a horrible death. ... Check out my mods -> 2001 Mazda Protege LX aka Rum Runner ... My front pass sidewindow won't go up or down anymore. haven't taken ...

Passenger Window on 2007 CX-7 will not come up ...

2 posts

Nov 28, 2012

Driver's side window auto-up/down issues - Mazdas247

15 posts

Jun 10, 2011

Power Window Problem - Mazdas247

7 posts

Aug 9, 2009

Driver Side window controller won't work

14 posts

Nov 11, 2006

More results from

2003 Mazda Protege 5 Replacing The Power Window Motor ...

? 7:02

Feb 3, 2015 - Uploaded by Steve K.

2003 Mazda Protege 5 Replacing The Power Window Motor and Regulator. Steve K. ... Looks like you just ... Dorman 741-741 Mazda Protege Fr

Oct 30, 2015 | 2002 Mazda Protege

1 Answer

Install timing belt correctly on 02 Mazda protege

The instructions to do that are beyond the scope of this site. Recommend that you buy a manual that describes how to do the job. It's not somethign you should do if you lack the experience.

Dec 08, 2014 | 2002 Mazda Protege

1 Answer

02 mazada protege code P0660

P0660 Intake Manifold Tuning Valve Control Circuit/Open.. Although you may want to first look at a new EGR Valve - particularly in Mazda.
PS: Your local auto parts store can also define OBD II Codes.
Best regards

Sep 24, 2011 | 2001 Mazda Protege

3 Answers

Mazda protege rear strut replacement 02

they're underneath the plastic deck cover in the back, where the speakers are. -just a few plastic fasteners and the wire connector for the rear light, and it'll pop right off. -just did it myself this weekend

Jan 03, 2010 | 2002 Mazda Protege

1 Answer

2002 Mazda Protege timing belt replaced and

Scan PCM for codes. Check that timing is correct again.These DOHC engines are easy to install a tooth out. Start from the top of engine when installing timing belt on this type of engine it's the easiest way to do it. If you took CRANKSHAFT pulley apart make sure the pick up ring behind isn't placed in backwards.

Oct 20, 2009 | 2002 Mazda Protege

1 Answer

02 mazda protege doesnt have any power and it has a knock to it like it missing firing

Well thenRemove 1 plug lead at a time and when the missing stays the same and dosent miss on 2 then you have the correct cylinder OR it could only be the plug faulty or lead ,but if none makes any differance then the knocking will be something else like Tappet lack of oil ,, valve hiting a piston, or timing moved.
Try all of the above and let me know how you get on . Ron

Oct 11, 2009 | 2000 Mazda Protege

1 Answer

2002 mazda protege 5, engine light on

That would be best because if one is bad then the other wont be far behind. Good luck dont forget to rate.

Mar 23, 2009 | 2002 Mazda Protege

1 Answer

Mazda protege antitheft system

2001 protage the battery keeps dying. What could be the problem.

Sep 11, 2008 | 2002 Mazda Protege

Not finding what you are looking for?
2002 Mazda Protege Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides