Question about Cars & Trucks

1 Answer

How can i remove the drivers door glass on my 64 fairlane

Posted by on

1 Answer

Remove the inner door panel to
get to the glass

Posted on Dec 08, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 65 mustang stalls whenever i stop then it starts right back up


Hello Larry,

Without the car running... You should be able to open
the throttle.. and literally DROP it back to idle...

Observe the action of the THROTTLE RETURN
DASH-POT
T should visibly SLOW the RETURN
of the throttle linkage like a door closer...

If you do not SEE the slowess... the dashpot
should be replaced (they are getting SCARCE).

SIX CYLINDER (EXAMPLE (only))
http://www.ebay.com/itm/NORS-65-67-MUSTANG-64-67-MERCURY-COMET-FORD-FAIRLANE-FALCON-DASH-POT-C2DZ9B549A-/142309387430?hash=item21224ceca6:g:kE8AAOSwo4pYmKnd&vxp=mtr


You will need to have the THROTTLE RETURN DASH-POT
on your (unspecified) carburetor
tested and adjusted... and the IDLE SPEED correctly set.

Idle Speed and a slow rate of RPM reduction is
critical to the proper function...

Some LESSOR "mechanics" will attempt to raise the
IDLE SPEED to compensate for a malfunctioning
DASHPOT... This will PROFOUNDLY exacerbate
the problem.

Throttle return dashpot (various pictures)
Go to Bing homepage

example DASHPOT (six cylinder)
NORS 65 67 MUSTANG 64 67 MERCURY COMET FORD FAIRLANE FALCON DASH POT...

example 1968 302/5.0L: Falcon, Mustang 2BBL carb
Carter 202 737 Carburetor Dashpot Ford 2 BBL Carburetors Replaces D7ZZ...

Hope this helps

Carnac the Magnificent

Jul 09, 2017 | Ford Mustang Cars & Trucks

1 Answer

I need to replace the drivers front window winding cable. how do i do that ? thanks Ants


best to buy this as an assembly. remove the drivers door panel behind the door is the window motor and regulator assembly. unbolt the regulator from the glass and remove the glass or prop the glass in the up position unbolt the motor and remove the assembly from the door and reinstall the assembly be carefull to position the nuts for the glass and make sure the pads that protect the glass are in place dont over tighten the nuts on the glass part or you will explode the glass

Jan 20, 2011 | 1999 Daewoo Lanos

1 Answer

Drivers door window replacement


Door glass bursting usually occurs due to heavy impact while closing the door or if the car is left in over heated environment. Some time it may occurs due to high beat of music system also.

Replacement of the window by self is not more complicated. You need to remove the door trim panel and other electrical connection from the doors.

Then clean the busted debries from the door thru' a vacuum cleaner. Purchase the right spare glass from the market. Remove the glass rail fittings from the position & fix the glass in the guide rails, then refix all the rails in position.

Put back the electrical connections & door trim in it place.

Jun 05, 2010 | 2001 Hyundai Elantra

1 Answer

How do i replace driver and passenger windows


Remove front door trim panel and water shield Raise glass to align nuts to access holes in inner door panel Remove nuts Separate glass from lift plate Lift glass upward through opening at top of door.

Oct 20, 2009 | 1993 Dodge Caravan

1 Answer

1994 Dodge Caravan driver's window won't close.


Start by removing the plastic insert at the door handle. This can be pried out with a screw driver, remove the door handle, prior out the plastic tabs, remove the screws there will be approximately four or five screws, lift the panel up and pull awar from the door. Remove the door regulator, you do this by using a punch and pundh out the rivets, then you drill out the aluminum holding in the glass using 1/4 inch drill bit, remove the door regulator and check for damage, you also need to remove the door motor and take it apart. The door motor will have three plastic plugs in the motor remove these, you can purchase new plugs at any auto store for $8.51, howevwer I would recommend you replace with ball bearings which can be purchased for $.64 cents each at any hardware store, pack the motor with wheel bearing grease and replace. You will need 1/4 inch bolts and lock washweer and nuts to replace the door regulator. Normally the switch will not be the problem. I would recommend you replace all the door regulators and rebuild all the motors. If one is going bad the others will follow. Expect to take allday to complete the job. Door regulators can be purchased on line for around $18 to 30 dollars. Good luck.

Jul 13, 2009 | 1994 Dodge Caravan

1 Answer

2003 ford taurus drivers window will not go up.


you either need a motor or motor and window regulator assembly.
SECTION 501-05: Interior Trim and Ornamentation 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Front Door Trim Panel Removal and Installation
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the front door trim panel screws.
  1. NOTE: To release the door trim panel two part pin-type retainers, first pull outward on the bottom of the door trim panel.
    Remove the front door trim panel.
    • Disconnect the electrical connectors.
c64985a.gif --------------------------------------
SECTION 501-11: Glass, Frames and Mechanisms 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Front Door Window Regulator And Motor
Special Tool(s) s2h~us~en~file=st1132a.gif~gen~ref.gif Heavy Duty Riveter
501-D011 (D80L-23200-A) or equivalent
Removal and Installation
  1. Remove the front door window glass. For additional information, refer to Front Door Window Glass in this section.
  1. Disconnect the front door window regulator motor electrical connector.
  1. Remove the window regulator rivets.
-----------------------------
SECTION 501-11: Glass, Frames and Mechanisms 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Door Window Regulator Motor Removal and Installation
  1. Close the window.
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the door trim panel. For additional information, refer to Section 501-05 .
  1. If equipped, remove the radio speaker.
  1. Position the watershield aside.
  1. Disconnect the door window regulator motor electrical connector.
  1. Remove the bolts and the door window regulator motor.
---------------------------------------------------

May 04, 2009 | Ford V6 Pony Cars & Trucks

1 Answer

Fallen driver's side window


probably need a new window regulator. ebay. 93 to 98 should fit.

Section 01-05: Trim, Interior 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  1. swv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .




  1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
  1. Pull the shop rag back and forth to release the window regulator handle clip.




  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screws from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
  1. Remove the front door trim panel.
Installation
To install, reverse the removal procedure.
---------------------------------------------------------
Window Regulator, Power Front Door
Removal
  1. Disconnect the battery ground cable (14301) .
  1. Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
  1. Remove the two front door brace bolts and the front door brace.


    415712f.gif

  1. Disconnect the front window regulator electric drive electrical connector.
  1. Remove the four front door window glass regulator track bolts.

    67b6136.gif


  1. Remove the three front window regulator electric drive bolts.
  1. Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
Installation
  1. Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
  1. Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
  1. Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.

Apr 29, 2009 | 1998 Mercury Villager

1 Answer

Drivers door window squeeks when it is opened.


before removing anything, try spraying some graphite spray down the side tracks of the door frame where the glass rolls up and down. do not spray the felts that go cross ways

Apr 26, 2009 | 2005 GMC Sierra

1 Answer

Rear Window- Drivers side- won't work


Removal and Installation
  1. Remove the rear door trim panel. For additional information, refer to Section 501-05 .
  1. Remove the watershield.
  1. Remove the interior weatherstrip.
  1. Remove the exterior-weatherstrip.
  1. Remove the nut and the rear window stabilizer.
  1. syh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removing the rivet center pins, place suitable support between the door outer panel and the glass to stabilize the glass.
    NOTE: Lower the window to access the rivets.
    Remove the two rivets retaining the rear door window glass to the rear door window glass run and bracket.
9eaea6b.gif
  1. Remove the rear door window glass.
  1. To install, reverse the removal procedure.

Apr 09, 2009 | 2000 Ford Taurus

2 Answers

Drivers door glass replacement 1999 ford contour


The first thing that you need to do is Go to the Auto Parts Store and get some Door Panel Fasteners for your car. You will Break a Few in the Repair. Next, Try and Locate ANY Screws or False Screw Hole Fillers in the Door Panel. Once you have found these Start at the Bottom of the Door Panel and slowly Pull it Off. Once you get it off, Clean out the Track that the Window Sits in with a screw Driver. Put some Clear Silicone Sealant into this Track and Insert the Window from the Top. Press Firmly into the Track and Slowly Raise the Window all the way up. Allow 24 Hours or so for the Sealant to Dry before Opening the Window.

Jan 23, 2009 | 1999 Ford Contour

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...