Question about 1999 Chevrolet Silverado 1500

1 Answer

Replace complete fuel line assembly in a Silverado z71 1500 4 whl. drive

Need to know how to remove front driveshaft and fuel line assembly

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Chevrolet Master
  • 808 Answers

Some of these drive shafts require removal of cross member to get them out. The fuel lines run up the back side of engine so removing the cross member will allow more room to gain access to the retaining hardware. jack up transmission and transfer case remove cross member lower down for access.

Posted on Dec 12, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

techbuster
  • 5081 Answers

SOURCE: Torque specs on a 2006 chevy silverado front hub

The nut on the axelshaft is 177 ft. LBS.
The 4 bolts on the bearing hub is 133ft. LBS.

Posted on Sep 14, 2009

  • 599 Answers

SOURCE: 2005 Chevrolet Silverado 1500HD 4 wheel drive

177 ft lbs

Posted on Dec 09, 2009

dgjtex
  • 405 Answers

SOURCE: I have a 1979 Chevrolet

Remove caliper and nut to axle should come of with a little help of a rubber hammer. Knock bolts out from the front and drive new ones in from the back. You can use a lugnut with the flat side down to help pull them in and a hammer to help. Hope this helps.

Posted on Dec 26, 2008

  • 2 Answers

SOURCE: need to replace driveshaft carrier bearing, will not come off transmission end.

First mark the relationship of the two yokes and then remove the universal joint. Now that's done remove the retainer clip from the top of the slip yoke and gently tap the slip yoke out being careful not to damage the splines on the shaft. the bearing that ins on there is pressed in so (A) you can bring it to someone with a press or (B) use a gear/ pulley puller. If you attempt this take your time and have patience don't break anything and think safety first.

Posted on Jan 05, 2010

  • 102 Answers

SOURCE: I would like to replace the headlight assembly of

There is a little aluminum stick in the assembly holding it in. On the top of the headlight twist the stick and remove it. It will look like a tent stake. Remove this stick and then the head light assembly will almost fall out.

Posted on Apr 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I remove the gas tank out of a 2006 Ford 500 no one knows


SECTION 310-01: Fuel Tank and Lines 2006 Freestyle/Five Hundred/Montego Workshop Manual REMOVAL AND INSTALLATION

All vehicles
  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02 .
  1. Release the fuel system pressure. For additional information, refer to Section 310-00 .
  1. Drain the fuel tank. For additional information, refer to Section 310-00 .
All wheel drive vehicles
  1. Remove the rear driveshaft. For additional information, refer to Section 205-00 .
All vehicles
  1. Remove the muffler. For additional information, refer to Section 309-00 .
  1. Disconnect the fuel vapor control tube assembly valve-to-fuel vapor tube quick connect coupling. For additional information, refer to Section 310-00 .
  1. Disconnect the fuel supply tube-to-fuel filter quick connect coupling. For additional information, refer to Section 310-00 .
  1. Disconnect the fuel vapor tube-to-fuel vapor control tube assembly valve quick connect coupling. For additional information, refer to Section 310-00 .
  1. Disconnect the fuel tank wiring harness electrical connector at the rear of the fuel tank.
  1. Release the clamp and remove the fuel tank filler hose from the fuel tank.
  1. Place a suitable lifting device under the fuel tank.
  1. Remove the 2 front fuel tank strap bolts.
    • To install, tighten to 35 Nm (26 lb-ft).
  1. NOTE: Do not bend the fuel tank straps.
    Loosen the 2 rear fuel tank strap bolts and position the 2 fuel tank straps aside.
  1. Lower the fuel tank enough to move forward, clear of the fuel straps then complete the lowering procedure.
  1. To install, reverse the removal procedure.

Procedure revision date: 08/19/2009


May 03, 2016 | Ford Cars & Trucks

1 Answer

How do I replace my carrier bearing in a 1988 Chevy Silverado extended cab long bed?


I'm guessing your you are referring to the drive shaft center support bearing. Remove u-joint 4 bolts at rear diff., then 2 bolts for center support. Slide driveshaft assembly out of trans. and lay on ground. On either side of the center support, make alignment marks on front and rear half of drive shafts with a crayon or tape (very important for re-assembly). Slide rear half off. Press out center support. Clean sleeve with emery cloth or 400 grit sand paper. Press on new center support, lube splines and reconnect drive shaft halves making sure alignment marks meet. Install assembly and torque bolts.

Dec 29, 2013 | Cars & Trucks

1 Answer

Is a 2004 ford f-150 2wd carrier bearing.. ( mid-mount bearing ) on driveshaft replaceable, or do i have to replace entire driveshaft?


it is replaceable
normally it comes complete in the rubber mount
you will have to undo the drive shaft flange at the bearing
remove the drive shaft and take it to an accredited drive shaft repair shop or take the vehicle to an accredited drive line specialist shop
the repair will require that you place the flange back on the shaft after the bearing replacement in exactly the right position or you will get harmonic vibration after the job so talk with the experts first if you want to diy

May 09, 2017 | Gateway Cars & Trucks

1 Answer

I'm trying to figure out how to remove a bearing from driveshaft off 2002 lincoln ls


Which bearing? The hub bearing? I can send it. I have your Ford shop manual & wiring books for $25, plus $4 shipping. Let me know.

SECTION 205-01: Driveshaft 2002 Lincoln LS Workshop Manual
DISASSEMBLY AND ASSEMBLY Driveshaft Center Bearing
Special Tool(s) s2x~us~en~file=st1260a.gif~gen~ref.gif 2-Jaw Puller
205-D026 (D80L-1002-L) or Equivalent s2x~us~en~file=st1368a.gif~gen~ref.gif Puller, Bearing
205-D064 (D84L-1123-A) or Equivalent s2x~us~en~file=st2454a.gif~gen~ref.gif Driveshaft Alignment Bushing Remover Tube
205-D073 or Equivalent
Disassembly
  1. Remove the driveshaft (4602). For additional information, refer to Driveshaft in this section.
  1. Separate the front and rear shaft assemblies.
  1. s2x~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not clamp on the driveshaft tube as a fracture can result.
    Position and clamp the driveshaft at the weld yoke.
  1. Using the special tools, remove the retaining ring and the center bearing and bracket assembly (4A499).
Assembly
  1. Position the center bearing and bracket assembly and the retaining ring on the yoke.
  1. Using the special tool, drive the retaining ring and bearing assembly until fully seated on the yoke.
  1. s2x~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Align the index marks or driveshaft imbalance can occur.
    Assemble the front and rear shaft assemblies.
  1. Install the driveshaft. For additional information, refer to Driveshaft in this section.

Sep 08, 2011 | Lincoln LS Cars & Trucks

1 Answer

Viberation in drive line truck has 7 u joints, replaced the 2 rear ones,vibe still there,but somewhat better. the rest of the seem to be ok is there a different shaft that would fit? at $50.00 a joint it...


Did you change the carrier bearing. It will be cheap compared to a transmission and new drive shaft. Got 1 in my shop right now. Customer did not listen. Check that carrier bearing Cost $1350vs $50

On vehicles covered by this information that are equipped with a two-piece rear driveshaft assembly, the center support bearing may be removed for replacement. To be sure if your driveshaft may be serviced, check with your local parts supplier or dealer for parts availability information.
  1. Matchmark and remove the rear driveshaft assembly. For details, please refer to the procedure located earlier in this section.
  2. Remove the strap retaining the rubber cushion from the bearing support.
  3. Pull the support bracket from the rubber cushion and the cushion from the bearing.
  4. Press the bearing assembly from the halfshaft.

To install:
  1. Assemble the center support bearing to the driveshaft:
    1. If removed, install the inner deflector onto the front shaft half and ***** punch the deflector at 2 opposite points to make sure it is tight on the shaft.
    2. Fill the space between the inner dust shield and bearing with lithium soap grease.
    3. Start the bearing and slinger assembly straight onto the shaft journal. Support the shaft and using a length of pipe over the splined end of the shaft, press the bearing and inner slinger against the shoulder of the front shaft half.
    4. Install the bearing retainer, the rubber cushion onto bearing, the bracket onto the cushion and the retaining strap.

  2. Align and install the driveshaft assembly to the vehicle.

Oct 21, 2009 | 1997 Chevrolet S-10 Pickup

2 Answers

2003 Silverado I bang on the gas tank and it starts but dies off after awhile. Checked the fuel pump, need to know how to change the electric fuel pump. There is 3 fuel lines that I need to know how to...


Just adding to the previous solution... When replacing the fuel pump, it make the job a lot easier to just pull the truck bed off. There are 6 bolts holding it on from underneath (also remove the gas cap screws) and it will lift off the frame. The bolts are very easy to reach with a 6 inch extension as long as you don't have duel exhaust in which case you will need a knuckle. Once the bed is off...you have free and easy access to the top of the fuel tank and pump. Use a brass punch to remove the retaining ring on top of the fuel tank. (a pump replacement kit can be rented at most auto parts stores).

Jun 09, 2009 | 2003 Chevrolet Silverado 1500

2 Answers

Part names


cardan centering bearing
point bolts needed to be removed that connects D.S.to transfercase

May 22, 2009 | 2001 Ford Excursion

Not finding what you are looking for?
1999 Chevrolet Silverado 1500 Logo

152 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...