Question about Ford Fusion

1 Answer

I have a ford fusion 2007 police pack, the signal lights and the high beam won't work how do i make it work ?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Ford Master
  • 519 Answers

Check Multi-Function Switch and/or Connection.

Posted on Dec 12, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
sparky1500
  • 1066 Answers

SOURCE: head lights not working

check your relays, they are like big fuses in your engine compartment, if your low beam and high beam relays are the same model, switch them and see if this enables low beams and disables the high beams. if it not the relays, or fuses, then it is probably your wiring harness, an expensive repair.

Posted on Nov 28, 2008

  • 512 Answers

SOURCE: low beams not working on 2007 dodge ram 1500

a possibility is the multifunction switch or the tipm being bad. check the wt/lg wire in the left headlamp assembly and the wt/tan wire in the right assembly for power

Posted on Jan 26, 2009

countrysi248
  • 443 Answers

SOURCE: low beams don't work

there is two things that could be wrong .. check under the hood for your power distribution box .. its black and 3 inches wide and about 8 inches long .. this contains your relays. and some fuses. on the inside of the lid it tells which one is which.. look for low beam relay .. if it is ok check your low beam bulbs and make sure they arent burnt out.. these two things should fix your problem .. or at least one of these should .. holler if you need more. Jerry

Posted on Apr 29, 2009

  • 14036 Answers

SOURCE: low beam and running lights will not come on

check relay and the fuse.

Posted on May 16, 2009

roniecon
  • 6826 Answers

SOURCE: Low beams shut off and won't come on other lights

Either the low beam head light bulbs have went out,or the dimmer switch has gone out.

Posted on Oct 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Headlights not working on low beam


Replace the turn signal switch. All exterior lights run threw it except the high mount brake light.

Dec 01, 2015 | 2007 Chevrolet Chevrolet Uplander

1 Answer

Rear brake cailpers won't collapse on 2007 ford fusion


Open bleeder valve & push caliper piston, in as
you rotate piston to screw in parking brake

Do this by hand,only use a clamp on the front calipers

Apr 08, 2013 | 2008 Ford Fusion

2 Answers

I have a 1995 Ford Explorer Limited and the high beams work but the low beams and fog lights do not, please help....


These trucks are known for bad multifuction switches.
the switch that i talk of is the signal switch , the handle is the switch, it bolts to side of steering column . this switch controls the signals and the headlights and high /low beams. the other thing is the headlight switch connector, the connector some times goes bad and starts to melt or just comes out of the connector. you will need to remove the cover to steering column, the screws are located under the bottom cover in holes. remove cover and check connector and then test for power if you have power going into switch but not coming out then switch is bad.

the last thing is to make sure the bulbs are good , make sure the headlight bulbs are good , and also the driving light bulbs, test for power at the connectors to those lights to.
You will need to do a little testing to find the problem.

Nov 22, 2012 | Cars & Trucks

1 Answer

Why my 2007 police crown Vic won't shift out of


All 2000 and up vehicles utilize a Solenoid which is powered by depressing the Brake Pedal to allow the Shift Lever to be move from Park to any other position. Is the Shift Lever located on the Steering Column or the Floor? In either case typically the Solenoids used by Ford do occasionally go bad. I highly recommend having a certified technician replace the solenoid.

Nov 18, 2011 | 2007 Ford Crown Victoria LX Sedan

2 Answers

2005 police P71 4.6L crown victoria. headlights work fine. pull back on signal handle, the blue light on display illuminates, yet headlights are out. no illumination to high beams. pull on handle again,...


The head light controls on a police car are exactly like those on any other Crown Vic. I have repaired dozens of them. More than likely you have no contact inside the multifunction switch. I would replace the switch as the most likely source of the problem. These are easy to change, just remove both halves of the plastic cover around the steering column and there are two Torx (also called star screws) screws holding the switch onto the column. The screws are on the bottom down in wells of the lower calm shell cover, they are cross points (Phillips)
This is a fairly common failure on police cars (P71 and P73 option).

Aug 28, 2011 | 2004 Ford Crown Victoria

1 Answer

My 95 ford windstar headlights won't turn on..but my high beams and parking lights work


I had the same problem with my 98 and the signal lights switch on the steering column was bad

Jun 13, 2011 | 1998 Ford Windstar

1 Answer

How can I adjust the headlights on my 2007 Fod


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 16, 2009 | 2007 Ford Fusion I4 SEL Sedan

3 Answers

Radio LCD Lights Don't work - 2007 Ford Fusion


I was told by the Ford dealership that I had to replace the entire radio. This is also happening with my Ford Fusion (2007). I opted not to replace w/ the same radio because what if it happens again?? My lights came back after some time, but who knows how long they will last.

Apr 14, 2009 | 2007 Ford Fusion I4 SEL Sedan

2 Answers

One high beam won't work.


There should be black split tubeing from the head light. Untape and check the connections that have been spliced. Usually the police flasher was hooked up at that point. You may have to follow the wires back to find the break.

Jun 18, 2008 | 2003 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...