Question about Chrysler 300

1 Answer

Is there a way to remove the transmission from a 1999 Chrysler 300 without removing the engine?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert that has over 500 points.

  • Expert
  • 186 Answers

Most transmissions can be removed from underneath the car.

Posted on Dec 07, 2014

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I just replaced my engine for a 06 chrysler 300. Started up fine. But when I put it in gear i get this knocking noise from the bell housing area.

You either left the torque converter bolts loose or the flex plate (flywheel) is Cracked, Usually around crankshaft flange. You can check the bolts without removing the engine, but the flex plate will require engine removal. Look in inspection opening while engine is running and check for run out (rotational wobble) of flex plate. This condition will cause extensive damage to torque converter and front pump seal in the transmission.

Feb 28, 2017 | Chrysler Cars & Trucks

1 Answer

Where is the transmission control relay located on a 1999 Chrysler 300 M

It is located inside the transmission. Unless you are skilled enough to remove the pan and the guts of a tranny leave it for a shop @ $200.

Apr 21, 2015 | 1999 Chrysler 300M

1 Answer

Does the engine need to be removed to replace 1999 chrysler 300 transmission

Nope ,the complete exhaust system has to come off and it can be removed from under the car

Dec 07, 2014 | Chrysler Cars & Trucks

1 Answer

Locating the oil plug on a 1999 Chrysler 300 M

I guess you are talking about the oil pan to drain the engine oil.
the transmission does NOT have a drain plug- that's why I asked in the first place.
But considering that, I think it is about a 13 or 14MM plug located on the right (Passenger) side of the engine under the car. The pan is a structured aluminum piece that hangs down almost even with the frame structure directly under the engine. Remember: righty- tighty, lefty- loosie.

Oct 03, 2011 | 1999 Chrysler 300M

1 Answer

Donde esta el termostato del 300 1999 chrysler

3.2L & 3.5L Engines
  1. Disconnect negative cable
  2. Drain cooling system.
  3. Raise vehicle on hoist.
  4. Disconnect electrical connectors from engine oil and power steering pressure switches.
  5. Disconnect radiator and heater hoses from thermostat housing.
  6. Remove thermostat housing bolts.
  7. Remove housing, thermostat, and gasket.

To install:

  1. Position gasket on thermostat and housing.
  2. Install thermostat housing, gasket and mounting bolts onto block. Tighten attaching bolts to 105 inch lbs. (12 Nm).
  3. Install radiator hose.
  4. Install bypass hose.
  5. Connect electrical connectors from engine oil and power steering pressure switches.
  6. Connect negative cable.
  7. Fill cooling system.
  8. Inspect for leaks.
  9. Lower vehicle on hoist.

Jan 23, 2011 | 1999 Chrysler 300M

1 Answer

Will a transmission in a 1999 chrysler concord interchange with on in a 1999 chrysler 300 m

yes they are the same transmission outside and have the same disignation of 42LE, but they may be different gear ratio's, they have tags on them that can id the internal differences, the 300 uses a 3.5 liter, which is not avail in the Conord

Jun 22, 2010 | 1999 Chrysler Concorde

1 Answer

Changing thermostat in 1999 chrysler 300

The thermostat is located at the end of the lower radiator hose at the engine Next to the oil filter. Sometimes it is easier to change the oil at the same time cause if you remove the oil filter it makes it easier to get to one of the bolts to remove the housing where the thermostat is. Hope this helps

Mar 19, 2010 | 1999 Chrysler 300M

1 Answer

Told the chrysler sebring crank sensor needs repair.......and that transmission needs to be removed to do it in this will run fine then just stop...with no immediate is a 1999....

Because it's on the back of the transmission bell housing, where the transmission and engine meet, it is very difficult to replace. I have replaced one and also had a dealership replace them. The transmission was not removed. I would recommend taking it to a repair shop where they have the proper tools for this repair/replacement. It will cost around $300.00. Call around for prices.

Aug 06, 2009 | 1999 Chrysler Sebring

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides