Question about 2004 Volvo V70

1 Answer

I replaced both axles , but when I brake it pulls to the driver side ( only when I brake)

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Volvo Master
  • 1,253 Answers

Likely suspects include:
unevenly worn brake pads
unevenly worn brake discs or drums
air in brake lines
uneven tire wear
wheels out of alignment

Unless you can troubleshoot effectively and perform the needed repairs, I would take the vehicle in for service. It could end up saving you lots of time and money in unneeded parts and labor.

Posted on Dec 07, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pull cv axle in 2001 ford escort 4 cylinder


remove wheel on side. remove brake caliper/brakes, disconnect lower ball joint, remove axle shaft hub nut. push axle out of hub, then pull half shaft out of transmission. install reverse.

Mar 07, 2015 | Ford Escort Cars & Trucks

1 Answer

How to remove the axel shafts from the Diff. 94 ford expl.


Do one side at a time, Jack the front wheel off the ground and remove. Remove the Brake Caliper and Rotor. Remove the large center nut in the Hub. Now remove the two bolts holding the lower part of the strut to the A-Arm and separate. You should be able to pull the hub down far enough to get the end of the axle out with some wiggling and possibly swearing, it not you can remove the lower A-Arm and just pull it off. PLACE A DRIP PAN UNDER THE SPOT WHERE THE AXLE GOES INTO THE TRANSMISSION BEFORE PULLING THE AXLE! Replace the axle to trany input seal and reverse order my instructions. Repeat for other side. This is a good time to replace Brake Pads and Rotors as well.

Apr 02, 2014 | 1988 Ford Ranger

2 Answers

Front end grinding


The end of the drive axle that goes into the diff is in splined into the side gear of the diff and will be dry as there would be no way to stop the oil coming out of the diff past the splines. The diff seal runs on the outside of the side gear and seals the oil in the diff. The drive axle slides in and out of the splined section to compensate for the changing lengths of the axle on turns. Grease on the splines would be a big help as it would allow the splines to move when under drive load.. Check the hub bearings for condition and adjustment and check the hub itself for wear indicators.

Dec 14, 2013 | 1994 Jeep Grand Cherokee

1 Answer

How do i replace the front axle seal drivers side n a 2004 escalade


remove axle nut, remove lower ball joint nut, pop drive shaft loose with punch or wood dowel , pop lower ball join from knuckle pull up push axle out of knuckle , pull back knuckle and tie in place pop out axle with big screwdriver or pry bar ,remove seal replace.

Aug 01, 2012 | 2004 Cadillac Escalade

1 Answer

I replaced the driver side wheel hub and now it pulls to the right and seems to float. Do both sides turn on a front wheel drive


Yes they do and they work independantly of each other. Each wheel has it's own axle and hub coming from the transmission mounted underneath the motor. If the car is pulling to the right you need to check the brakes and make sure they are not grabbing. Front wheels usually have disc brakes and the calipers tend to bind up and grab over time, this will cause the car to pull to the right. You might also have an alignment issue and that can cuase the car to pull, even a low tire will cause this. The floating issue is probably due to a worn strut and it is not doing its job as a shock absorber. When your replaced the hub did you also replace the axle? The axles must also match up to each other. The car could also be pulling to the right because you replaced the left hub and it now is turning with less friction than the right. You should go ahead and replace the right and check the brakes for any grabbing or worn rotor. Once this is done get an alignment and this should resolve the pulling issue.

Jan 08, 2011 | 1989 Ford Tempo

2 Answers

How do i chage a c/v axle on a hyundai tiburon


Specifically for 2003 Tiburon V6 6 speed, but may work for you as well.
-Loosen tire lugs
-Remove center caps with screw driver or similar tool (careful not to scratch caps)
-loosen axle nut

-Jack the car up and place on jack stands
-Chalk rear wheels
-finish removing tire lug nuts and tire
-remove cotter pin and finish removing axle nut
-remove brake pads
-remove caliper and brake assembly
-remove rotor (possible PITA), use extreme caution hammering a stuck rotor!

IMPORTANT STEP:
*remove 2 bolts from strut mount assembly. This will allow you enough clearance to "cleanly" pull axle out with minimal force/hammering. No axle puller tool necessary and no messing with the lower ball joint.

-Now gently tap the axle out of the hub assembly
-pull the rest of the axle out of the hub assembly by hand or pry with long screw driver or pickle fork. Again, since you removed the 2 strut assembly bolts, your hub assembly should have dropped down and away from the axle quit a bit to allow you enough clearance to remove axle from hub assembly

**Follow next steps for DRIVER SIDE ONLY**
-Next, place a fluid pan to catch any leaking trans fluid before removing axle from transmission side.
-Using a long screwdriver or pickle fork, pry the axle away from the transmission
-Remove entire axle and replace with new one
-Installation is reverse of removal steps. (not difficult, just line up the splines and everything should "pop" in place

Jun 09, 2010 | 2003 Hyundai Tiburon

3 Answers

How to replace rear Axle seal on 4x4 chevy


this is very hard if you do not know what you are doing. Ill try to step you through this
  • pull wheels
  • drain pun-kin case
  • pull rear cover
  • in between the spider and axle sets pull C ring with needle nose pliers
  • pull hub and axle out CAREFULLY as there are roller bearings on the end of the axle housing
  • pull seal out at the end of axle housing
  • tap in new seal CAREFULLY and straight DO NOT BEND IT or it will be junk
  • replace axle carefully as the roller bearings are still there
  • replace C clip to original position
  • replace axle diff cover and replace the gasket with a new one
  • refill diff case
  • install tire
  • your good to go

May 03, 2010 | 2002 Chevrolet Silverado

2 Answers

Drivers side rear axle is leaking, not brake fluid, has disc brakes, what do i need to do to replace seal?


i will tell you right off this is a job for a qualified mechanic,the axle has to be pulled off first you jack up that wheel dismantle the brakes and rotor and behind the axle hub are four bolts that hold on the axle remove them and axle will come off the rear end cover does not have to come off and the axle fluid also does not have to come out,but now that axle is out you will notice that a wheel bearing is holding the seal in place this is pressed in you can buy these as a set at the dealer but must be removed by a pro. as not to harm axle and it has to be pressed back in

Feb 06, 2010 | 1995 Jeep Grand Cherokee

1 Answer

1999 jeep grand cherokee limited


Remove the brake parts tie the brake caliper out of the way, break loose the tie rod and lower ball joint, move the steering knuckle out of the way, pull the axle straight out with a sharp snap motion.

Jul 03, 2008 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
2004 Volvo V70 Logo

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...