Question about Cars & Trucks

1 Answer

1991 D21 - Lost blinkers & flashers. Changed flash box. No luck. Next, I replaced the blinker assembly. Still nothing. What could I be missing?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 26 Answers

Check over your whole wiring harness. a fusable link may be out that you can't find. there's also probably relays involved, and, knowing Japan, they may have a regular fuse on each of them as well. double check the bulbs for the blinkers, too.

Posted on Dec 08, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 71 Answers

SOURCE: fuse diagram on chevy s10 pickup extended cab.

flasher located at bottom of fuse box its round bout the size of a pop bottle lid,hazard flasher located at top

Posted on Mar 27, 2009

VREGG
  • 41 Answers

SOURCE: Blinkers stay solid and dont flash, Hazards work fine.

CHECK GROUND ON TAIL LIGHT HOUSING.

Posted on May 08, 2009

  • 73 Answers

SOURCE: 99 jeep cherokee Blinker problem

Hi Bill,I think before replacing anything else you should give that hazard switch a good workout.The switch doesn't get get used very often and the contacts get corroded and can upset the indicators.Good Luck.

Posted on May 16, 2009

  • 10 Answers

SOURCE: fuse diagram on chevy s10 pickup extended cab.

behind the radio, take the radio and the cover that goes over it. it should be there next to the hazard ligths flasher.

Posted on May 28, 2009

  • 44 Answers

SOURCE: hazards and blinkers not working

There are separate fuses for the turn signals and blinkers, but you should check both of them just to see if they're good.

You may have a burnt out turn signal bulb as well. I know that this sounds like an obvious answer, but a single bulb can sometimes disable the entire system because of the way that some flashers operate.

You could also have a defective turn signal/hazard light flasher. This is located under the dash board on the driver's side between the steering column and the door. You have to remove the sound insulation/kick panel (the cover on the bottom of the dash board) to reach the flasher (it is easy to remove - I don't think you even need tools).

Posted on Jul 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn signals not working on my 98 Mustang. Hazards work fine. Already replaced the multifunction switch. Didn't help.


Sounds more like the flasher to me,in the drivers side fuse panel
square box ,looks like a relay , 5 male spade connectors on back.

Mar 24, 2014 | Ford Mustang Cars & Trucks

1 Answer

Blinker come on but don't flash bulbs and flasher are ok


this usually means you have a turn signal bulb that is burned out. The blinker measures the power to the bulbs and that controls the flash rate. If a bulb is burned out it does not flash.

Also if you changed your bulbs to LED the current draw is less and could cause the same situation

Aug 24, 2013 | 1991 Dodge Dakota

1 Answer

My two front blinkers turnon but won't flash and my rear blinkers flash but fast. how do i fix the problem??


Have you changed the bulbs recently, with the same wattage? this can cause difference in the flash rate.Cehck with a tester meter if the flasher unit is faulty.hope this helps

Jun 30, 2010 | 1991 Nissan Maxima

1 Answer

Where is the flasher relay unit


1ST double check that all the bulbs for the pass. side turn signals are working. if even one is out it can make the blinker not "blink". so compare the pass. side lights to the driv. side to make sure u did not miss something. NEXT,if thats not the problem, then u can locate the flasher by 1ST looking in the fuse box(probably inside the glove box or under the drivers side dash) theres a good chance it might not be there(years ago every car had the flasher in the fuse box) SO TURN ON THE DRIVERS SIDE BLINKER (key on) and LISTEN OR FEEL UNDER THE DASH FOR THE FLASHERS NOISE--LOOK NEAR THE STEERING COLUMN,BRAKE PEDAL, EVEN BEHIND THE ASH TRAY!! hope this helps you!

Sep 07, 2009 | 1994 Buick Century

2 Answers

Hazards and blinkers not working


There are separate fuses for the turn signals and blinkers, but you should check both of them just to see if they're good.

You may have a burnt out turn signal bulb as well. I know that this sounds like an obvious answer, but a single bulb can sometimes disable the entire system because of the way that some flashers operate.

You could also have a defective turn signal/hazard light flasher. This is located under the dash board on the driver's side between the steering column and the door. You have to remove the sound insulation/kick panel (the cover on the bottom of the dash board) to reach the flasher (it is easy to remove - I don't think you even need tools).

May 16, 2009 | 1997 Pontiac Grand Am

2 Answers

97 Chevy truck blinkers not working but hazards do


Try replacing the Flasher first before spending to much money for a possible simple fix. If it's not your flasher then it could be the turn signal leaver.
Ok, this may seem stupid, but that's what they did to the blazer. They set the flasher near the middle and under the center console behind the radio.


It's to the left of the radio right behind the dash. The hazard flasher and the turn signal flasher are side by side.  It right next to the Cig lighter behind the panel. They do mark the turn signal from the hazard flasher on the plastic behind them. Turn is on the right.

Good luck and hope this helps.

May 02, 2009 | 1997 Chevrolet Blazer

1 Answer

2000 blazer break lights stuck on


check the gruond in the black wire in the blinker switch if its ok, sometime the after market parts have ashort life time try to replace the flasher switch ( blinker switch)

Mar 07, 2009 | 2000 Chevrolet Blazer

1 Answer

Blinkers / flasher problems


If you got an owners manual it should tell you in there the location of the flasher. if no manual it should around where the fuse box is.

Feb 13, 2009 | 1991 Oldsmobile Toronado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...