Question about 1998 Chrysler Sebring

3 Answers

How to loose stabilizer link nut? - 1998 Chrysler Sebring

Posted by on

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer got voted for 20 times.

  • Chrysler Expert
  • 252 Answers

Those things get really stuck, most of the time i just cut them off and get new ones

Posted on Jan 03, 2015

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

Agreed with SloopJohn. If you are replacing them, don't worry about it breaking. It might actually make it easier to remove. Usually they have a lock nut which always makes it tighter.

Posted on Dec 07, 2014

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 128 Answers

Put a wrench on it and turn it. If there is a bolt, you'll have to hold the bolt head with another wrench.

Posted on Dec 07, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

How to Replace a Stabilizer Link in a Toyota Tundra car?


1) First of all make sure the vehicle is completely cool. Then disconnect the battery ground wire.
2) Then place the vehicle on a rack or raise the front of the vehicle on supports.
3) Then remove the front wheels and tires.
4) The Loosen the nuts that connect the stabilizer bar links to the lower control arm.
5) Then remove the nuts and disconnect the links from the lower control arm.Stabilize the link with the help of the wrench. Remove the nut and remove the retainers, cushions and link. Pull the bolts then remove the stabilizer bar along with the brackets and cushions.
6) Then put the new stabilizer in position. Install the two cushions and the two brackets. Tighten the bolts to 19 to 22 foot pounds. Then steady the stabilizer bar link with a wrench. Put the link on the lower control arm. Install a new nut. Torque the nut to 10 to 14 foot pounds.
7) Put the front wheels and tires back on the vehicle. Lower the vehicle.
8) Then Road test the vehicle to assure proper handling.

This will help.goodluck.


on Feb 28, 2010 | Toyota Tundra Cars & Trucks

Tip

How to Remove a Stabilizer Link in a VW Passat car?


The instructions to replace the Stabilizer Link in a car is follows:-- 1) First of all make sure the vehicle is completely cool. Then disconnect the battery ground wire.
2) Isolate the removed battery ground wire to avoid accidental contact with the terminal during the procedure.
3) Then place the vehicle on a rack or raise the front of the vehicle on supports.
4) Then remove the front wheels and tires.
5) Then carefully loose the fasteners that hold the ends of the sway bar.
6) Then remove the nuts and bolts from the brackets.4
Then remove the stabilizer (sway) bar from the vehicle.
NOTE:-- While removing the stabilizer bar be very careful that no proximate cables get caught on the bar and pulled out.
That is all.the Stabilizer Bar and Links are removed. This will help.Good luck.

on Feb 28, 2010 | Volkswagen Passat Cars & Trucks

1 Answer

What does the control arm on the front left driver side supposed to look like fully assembled


Hello! First diagram is the lower...Second is the upper..Guru...saailer

LOWER IDENTIFICATION:




Item
Part Number Description 1
5495 Stabilizer Bar Link Bolt and Bushing Assembly 2
18A192 Nut, Washer and Bushing Assembly 3
808264 Bolt 4
5005 Frame 5
5B326 Torsion Bar (LH) 6
5B327 Torsion Bar (RH) 7
620481 Nut 8
5C491 Nut and Washer 9
3079 Front Suspension Lower Arm (LH) 10
3078 Front Suspension Lower Arm (RH) 11
3A130 Tie Rod End 12
808166 Nut 13
808167 Nut 14
5K483 Front Stabilizer Bar Link 15
5482 Front Stabilizer Bar 16
5484 Front Stabilizer Bar Bushing 17
3B353 Front Stabilizer Retainer 18
N807396-S100 Bolt A
- Tighten to 40-55 Nm
(30-40 Lb-Ft) B
- Tighten to 150-200 Nm (111-148 Lb-Ft) C
- Tighten to 21-29 Nm
(15-21 Lb-Ft)


UPPER IDENTIFICATION:
Item Part Number Description 1 3C156 Damper Assembly (RH) 2 805348 Nut and Washer 3 - Shock Absorber Insulator
(Part of 18198) 4 3C157 Damper Assembly (LH) 5 3020 Front Suspension Bumper 6 3083 Front Suspension Upper Arm Assembly A - Tighten to 34-47 Nm
(25-35 Lb-Ft)



LOWER DIAGRAM FOLLOWED BY UPPER:

2_12_2012_9_47_51_pm.gif2_12_2012_9_54_26_pm.gif

Feb 12, 2012 | 1996 Ford Explorer

2 Answers

I have replaced the stabilizer links on my 2008 Pontiac G6 base model and I cant find the torque specs for the nuts.


Thanks for using FixYa.


Stabilizer Links

Removal & Installation

  1. Raise and support the vehicle.
  2. Remove the front tire and wheel assembly.
  3. Disconnect the stabilizer link from the stabilizer shaft.
  4. Disconnect the stabilizer link from the strut assembly and remove from the vehicle.

To install:
  1. Connect the stabilizer link to the strut assembly.
  2. Tighten the stabilizer link nut to 48 ft. lbs. (65 Nm).
  3. Connect the stabilizer link to the stabilizer shaft.
  4. Tighten the stabilizer link nut to 48 ft. lbs. (65 Nm).
  5. Install the front tire and wheel assembly.
  6. Lower the vehicle.

Mar 04, 2011 | Pontiac G6 Cars & Trucks

1 Answer

Remove and replace Front Sway bar


Hello ggagne.
Here is the procedure.

  1. Raise and suitably support the vehicle.
  2. Remove the left tire and wheel assembly.
  3. Remove the pinch bolt from the lower intermediate steering shaft
  4. Loosen all insulator clamp attaching bolts.
  5. Place a jack stand under the center of the rear frame cross member.
  6. Remove the rear frame-to-body bolts.
  7. Lower the rear of the frame just enough to gain access to the stabilizer shaft.
  8. Remove the insulator clamp bolts and the clamps from the frame.
  9. Remove the insulators from the stabilizer bar.
  10. Remove the stabilizer bar links from the control arms.
  11. Pull the stabilizer shaft rearward.
Installation
  1. Insert the stabilizer shaft to the left side of the vehicle. Important: DO NOT tighten the stabilizer link nut at this time. The weight of the vehicle must be supported by the control arms such that you can obtain the vehicle design trim heights before tightening the link nut.
  2. Loosely install the stabilizer shaft link at the control arm.
  3. Install the insulators on to the stabilizer bar.
  4. Connect the insulator clamps to the frame.
    • Tighten the stabilizer shaft bracket bolts to 48 Nm (35 ft. lbs.) .
  5. Raise the frame into position while you guide the steering shaft onto the gear.
  6. Install the new frame-to-body attaching bolts.
  7. Remove the jack stand.
  8. Install the pinch bolt and tighten.
  9. Install the left tire and wheel assembly.
  10. Lower the vehicle.
  11. Support the weight of the vehicle by the control arms.
  12. Tighten the stabilizer link nut.
    • Tighten the stabilizer shaft link nut to 23 Nm (17 ft. lbs.)
There you are, I hope your job goes well.
Thank you for using FixYa.

KL

Nov 13, 2010 | 2002 Buick Century

1 Answer

Replace broken sway bar for a 1996 ford windstar


Section 04-01: Suspension and Wheel Hubs, Front 1996 Windstar Workshop Manual REMOVAL AND INSTALLATION Stabilizer Bar Removal
  1. Raise and support the vehicle. Refer to Section 00-02 .
  1. Support vehicle with hoist or safety stands behind front sub-frame (5C145).
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the 6 mm drive hole in the front stabilizer bar link ball stud, do not use an Allen wrench to break loose or tighten or final tighten the front stabilizer bar link-to-shock absorber nut.
    Using care not to damage the front stabilizer bar link ball stud seal, remove the RH and LH front stabilizer bar link-to-front shock absorber nut.




  1. Using care not to damage the front stabilizer ball link stud seal, remove the RH and LH front stabilizer bar link-to-front stabilizer bar nut.
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use extreme care not to damage the ball joint boot.
    With another set of support safety stands under front sub-frame, remove two rear sub-frame retaining bolts. Lower rear of the front sub-frame to obtain access to stabilizer bar brackets (5486).
  1. Remove front stabilizer bar bracket bolts, stabilizer bar brackets, stabilizer bar bracket insulators and front stabilizer bar (5482) as required.
Installation
  1. Clean front stabilizer bar to remove dirt and contamination in area of stabilizer bar bracket insulator installation position.
  1. Lubricate inside diameter of new stabilizer bar bracket insulator with Rubber Suspension Insulator Lube E25Y-19553-A meeting Ford specification ESF-M99B112-A or equivalent. Do not use any mineral or petroleum based lubricants as they will deteriorate the rubber stabilizer bar bracket insulators.
  1. Install new stabilizer bar bracket insulators onto front stabilizer bar and position them in approximate location.
  1. Install stabilizer bar bracket on stabilizer bar bracket insulators and install new bolts. Tighten to 55-63 Nm (40-46 lb-ft).
  1. Raise front sub-frame and install new front sub-frame-to-body retaining bolts. Tighten to 115-132 Nm (85-97 lb-ft).
  1. Install front stabilizer bar link (5K483) to front shock absorber. Use care not to damage link ball joint boot seal.
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the 6 mm drive hole in the front stabilizer bar link ball stud, do not use an Allen wrench to break loose or tighten or final tighten the front stabilizer bar link-to-shock absorber nut.
    Install a new front stabilizer bar link-to-shock absorber nut. Tighten to 90-100 Nm (66-74 lb-ft).

  2. 66a0f1a.gif

Apr 28, 2010 | 1996 Ford Windstar

3 Answers

Replace swaybar 1999 silverado



Removal & Installation

  1. Raise and support the vehicle.
  2. Remove the tire and wheel.
  3. Remove the stabilizer shaft nut from the link bolt.
  4. Remove the stabilizer shaft link bolt.
  5. Remove the stabilizer shaft link insulators and spacers.
  6. Remove the oil pan skid plate, if equipped.
  7. Remove the stabilizer shaft insulator bracket bolts.
  8. Remove the stabilizer shaft bracket.
  9. Remove the stabilizer shaft.
  10. Remove the stabilizer shaft insulators.
  11. Inspect all of the parts for wear and damage.

To install:
  1. Install the insulators to the stabilizer shaft.
  2. Install the stabilizer shaft.
  3. Install the brackets over the insulators and the stabilizer shaft.
  4. Install insulator bracket bolts and tighten to 37 ft. lbs. (50 Nm).
  5. Install the stabilizer shaft link insulators and spacers.
  6. Apply Loctite® on the threads of the stabilizer link bolts then install the bolts.
  7. Install the stabilizer shaft nut to the link bolt and tighten to 89 inch lbs. (10 Nm), and continue to tighten the nut until 2-4 threads protrude above the nut.
  8. Install the oil pan skid plate, if equipped.
  9. Install the tire and wheel assembly.
  10. Remove the safety stands
  11. Lower the vehicle.

Mar 30, 2010 | 1999 Chevrolet Silverado 2500

1 Answer

Corvette sway bar installation


Stabilizer Bar: Service and Repair
Front
Removal Procedure
1. Raise and support the vehicle. Refer to Vehicle Lifting.
2. Remove the tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation.
3. Remove the stabilizer shaft link nuts from the stabilizer shaft.
4. Remove the stabilizer shaft insulator clamps from the front crossmember.
5. Remove the stabilizer shaft from the vehicle.
Installation Procedure
1. Install the stabilizer shaft, insulator clamps and bolts to the crossmember.
2. Install the stabilizer shaft links to the stabilizer shaft.
Notice: Refer to Fastener Notice in Service Precautions.
3. Install the stabilizer shaft link nuts.
- Tighten the stabilizer shaft link nuts to 72 Nm (53 ft. lbs.).
4. Install the stabilizer shaft insulator clamp bolts.
- Tighten the stabilizer shaft insulator clamp bolts to 58 Nm (43 ft. lbs.).
5. Install the tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation.
6. Lower the vehicle.



Stabilizer Bar: Service and Repair
Rear
Removal Procedure
1. Raise and support the vehicle. Refer to Vehicle Lifting.
2. Remove the tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation.
3. Remove the stabilizer shaft link nuts from the stabilizer shaft.
4. Remove the stabilizer shaft clamps, bolts and nuts retaining the shaft to the crossmember.
5. Remove the stabilizer shaft from the vehicle.
Installation Procedure
1. Install the stabilizer shaft to the vehicle.
Notice: Refer to Fastener Notice in Service Precautions.
2. Install the stabilizer shaft insulator clamps to the stabilizer shaft and the crossmember.
- Tighten the stabilizer shaft insulator clamp bolts to 65 Nm (49 ft. lbs.).
- Tighten the stabilizer shaft insulator clamp nuts to 95 Nm (70 ft. lbs.).
3. Install the stabilizer shaft links to the stabilizer shaft.
- Tighten the stabilizer shaft link nuts to 72 Nm (53 ft. lbs.).
4. Install the tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation.
5. Lower the vehicle.


Oct 30, 2009 | 2001 Chevrolet Corvette

1 Answer

Front Sway bar(Stabilizer bar)


please give good rating if this helps


Section 04-01: Suspension and Wheel Hubs, Front 1996 Taurus, Sable Workshop Manual REMOVAL AND INSTALLATION Stabilizer Bar Removal
  1. Raise vehicle on a hoist. Refer to Section 00-02 .
  1. Support vehicle with hoist or safety stands behind front sub-frame (5C145).
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use extreme care not to damage boot seal. Do not use power tools to tighten nut, or bearing and seal damage will result. Install nut using hex hold feature to prevent the stud from rotating.
    Remove and discard nuts retaining stabilizer bar link (5K484) assembly to front stabilizer bar (5482) and front shock absorber (18124) with an 8 mm closed-end wrench and an 18 mm open-end wrench.


    ccf2026.gif

  1. Remove nuts retaining steering gear (3504) to front sub-frame, and move steering gear off the front sub-frame.
  1. With another set of support safety stands under front sub-frame, remove two rear subframe retaining bolts. Lower rear of the front sub-frame to obtain access to stabilizer bar brackets (5486).




  1. Remove front stabilizer bar U-bracket bolts and replacestabilizer bar brackets and/or front stabilizer bar as required. Discard lower suspension arm stabilizer bar insulator (5493) and bolts.
Installation
  1. Clean front stabilizer bar to remove dirt and contamination in area of stabilizer bar insulator installation position.
  1. Lubricate inside diameter of new lower suspension arm stabilizer bar insulator with Rubber Suspension Insulator Lube E25Y-19553-A or equivalent meeting Ford specification ESF-M99B112-A. Do not use any mineral or petroleum based lubricants as they will deteriorate the rubber lower suspension arm stabilizer bar insulators.
  1. Install new lower suspension arm stabilizer bar insulators onto front stabilizer bar and position them in approximate location.
  1. Install stabilizer bar bracket on front sub-frames and install new bolts. Tighten to 30-40 Nm (22-29 lb-ft).
  1. Raise front sub-frame and install new front sub-frame-to-body retaining bolts. Position steering gear onto front sub-frame and install retaining nuts. Tighten to 115-135 Nm (85-99 lb-ft).
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use extreme care not to damage boot seal. Do not use power tools to tighten nut, or bearing and seal damage will result. Install nut using hex hold feature to prevent the stud from rotating.
    Install stabilizer bar link to front shock absorber and to front stabilizer bar, making sure that the stabilizer bar link is properly positioned. The letters "Top LH" and "Top RH" are moulded into the stabilizer bar link for correct assembly to the front shock absorber strut.
  1. Install new nuts and secure stabilizer bar link assembly to front stabilizer bar and front shock absorber. Tighten to 77-103 Nm (57-75 lb-ft) at front shock absorber strut and 47-63 Nm (35-46 lb-ft) at front stabilizer bar.
  1. Remove safety stands.
  1. Lower vehicle.

Apr 11, 2009 | 1995 Ford Taurus

Not finding what you are looking for?
1998 Chrysler Sebring Logo

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...