Question about Holden Cars & Trucks

1 Answer

How to fix LHS front door remote. Lock on holden statesman wl

New door lock

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Expert
  • 79 Answers

More than like if its just on door that wont look and the hoon sounds the door actuator will be faulty and you will need to replace the actuator.
To do this you will need pull the inside door handle off.
remove all door trim covers to access screw and disconnect mirror wiring.
remove all screws around door trim.
very carefully remove door trim once the trim is off you see a plastic inner door liner don't rip gently remove half .
look inside door and you will see the door actuator and lock,carefull lift up locking tabs so you can remove all door rods from actuator.
on the outside of door undo the 3 bolts and actuator will come out.
get the new actuator and fit it the same way the old one come out.
Before refitting the trim grab some silicon and reseal plastic to door to keep water out..

Posted on Feb 19, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Holden statesman sle 1979 colour mulberry can you tell me the paint identification number Thanks Alan


Hi Alan Check all id Plates normally have paint code
(1) near front strut mounts (2) front panel top, in front of radiator (3) Firewall Panel across rear of engine (4) B pillers inside of front doors.these are the normal areas for id Plates. If no luck try car panel shop normally have colour cards to match paint with paint code. Good luck

May 25, 2017 | Holden Cars & Trucks

1 Answer

Remote doesn't work to unlock drivers door nor doesn't the key work to unlock what should I do


The lock rod must have fallen off due to a broken retainer. remove the door panel and repair whatever issues you find with the lock rod. If the plastic rod retainer is broken the dealer can supply a new one for about $2.00 US

Jun 06, 2016 | 1998 Holden VT Commodore

1 Answer

Hi, I have a Holden Astra TS city 98 model car and the remote on the key will open all the doors except the drivers door, so to lock all doors I have to put the key in the drivers door or use the remote &...


A plastic clip that holds the lock linkage is probably broke or worn. You need to pull of the inner door panel to see whats going on inside. Use the remote and see whats happening. It could be bent rod in door from someone using a slim jim to unlock it when they locked the keys in it at some point. Bend the rod and try the remote again untill it works properly.

Aug 31, 2014 | Cars & Trucks

1 Answer

Wl statesman problems


short circuit in the wiring or the blinker stalk is faulty and constanly contacted

Jul 13, 2014 | 2002 Holden Caprice

1 Answer

Free wheel hub LHS not locking


Thegrease inside the hub may have gone hard. So you might need to pull it off, open it up and give it a good clean in kero, and finsihing off with degreaser. Wash out degreaser with warm detergent water. Reassemble and apply some new grease for lubrication. Not too much that it leaks out too easily. Also make sure your clean out any dust in the narrow gaps between the out rotating parts. This dust and grime just makes it hard to lock and un-lock the hubs. After cleaning ut the dust using WD40 or simillar, and constant working back and orwad in a container of kero, re-lubricate with WD40. Should last a few years before it needs to be done again.

Apr 06, 2014 | 2003 Holden Jackaroo

1 Answer

Doors lock remote driver


you could need new batteries in the remote.

Dec 17, 2013 | 1998 Holden VT Commodore

1 Answer

Open door manually


can it open from the outside? There is a child safety lock inside the door when open it could have been put on child proof not allowing a young child to open the door from the inside but it will still open from outside. if this is not the problem then your rod has disconnected from the latch mechanism inside the door, you may need a slim jim tool or try to remove door panel from inside, this will be difficult when door is shut but maybe possible depending on the door panel itself, they may have some screws but most just snap in.

Dec 10, 2013 | Cars & Trucks

1 Answer

Program remote 1996 chrysler lhs


Setting in the car remote in hand turn the key on and off ( don't start the car ) three times within 5 seconds. Now press the door lock button until the doors lock and stop it should now work.

Oct 03, 2009 | 1997 Chrysler LHS

2 Answers

How do i shut off or disengage the alarm system on a 1996 chrysler lhs ligths flash ,horn honks, and car will not stay running. i do not know why alarm set it self do not remoteless entry key pad so i am...


Man,I just bought a 96 chrysler lhs(salvage title) and we drove it home...Had no keypad.My girl and I got out and she left her purse...I opened the door and that car started honking and everything...Alarm wouldnt cut off so,What i did was go to the driver's door,Put the DRIVING KEY IN THE LOCK and locked and unlocked the door...Then,the alarm went off.Try that and if it doesnt work...Try to use those buttons.

Mar 08, 2009 | 1996 Chrysler LHS

1 Answer

Need of programming instructions for keyless entry for 1996 LHS


System operation
System will automatically lock all doors when vehicle is driven in excess of 15 mph
Pressing UNLOCK (on remote) once deactivates system and unlocks driver door only
Pressing UNLOCK (on remote) twice w/in 5 seconds deactivates system and unlocks all doors
Alarm/central locking functions can be altered using remote transmitter


Programming

Access data link connector (DLC)- druvers sude fascia
Switch ignition on
Jump DLC terminal 1 and ground
Ensure doors lock and unlock, indicating programming mode active
Press any button of each remote to be programmed
Ensure doors lock and unlock after each remote operation - indicating programming complete
Remove jump lead to exit programmming code

A maximum of two remotes can be programmed

Jan 20, 2009 | 1997 Chrysler LHS

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Holden Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14380 Answers

Are you a Holden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...