Question about Cars & Trucks

1 Answer

I have a Clark 743 bobcat and i have lost forward and reverse on one side it takes up in both directions but will not drive. can any one help?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 42,075 Answers

It could be sheared splines , broken chain hydraulic motor failure drive sprocket loose on shaft.

Posted on Dec 06, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I get a wiring diagram for a G series Clark Melroe Bobcat 753 2003 model please


Here is a link to the complete manual, https://www.slideshare.net/jieruikong/bobcat-753-service-repair-manual-pdf.

Feb 23, 2017 | Cars & Trucks

1 Answer

I have lost forward gears on Jeep Grand 2.7CDR taking only in reverse


the transmission computer computer has gone into fail safe mode

an electronic failure not a mechanical failure
could be something simple as a computer re-set or
a transmission solenoid s

will need a jeep service center
or automatic transmission work shop to fix it



26314380-xmqclvgem1na1ssuwwrabsdr-1-0.jpg

Oct 17, 2016 | Jeep Cars & Trucks

1 Answer

Have a 763 bobcat n right side wheels won't go forward any ideas on what this might b??


Broken chain in drive line on right side or chain sprocket.

Oct 02, 2016 | Cars & Trucks

1 Answer

BOBCAT V417 RUNS BUT HAS NO FORWARD OR REVERSE


it is possible that while the brake light is on then there will be no drive action as the hydraulics will be isolated by the brake system. Check the reason for the brake light on and you may find the reason for no drive.

Dec 18, 2013 | Cars & Trucks

1 Answer

Ford e-250 transmission problems


My Econoline 250 with 4.2 lost fluid from hose leak, fixed leak everything was normal for 3 days till I drove it on highway. When it went into overdrive lost forward power. Turned off OD and did ok for a while. Lost forward gears slowly, put in fluid, hard to tell when full. Reverse is fine but have to rev up engine to get forward to engage, then everything is fine at lights and such till take out of drive, then have to rev engine to about 2500rpm to engage drive. Help?

Nov 05, 2013 | 1990 Ford F250

1 Answer

I have an '04 Silverado w/4l60e. When I shifted from reverse to drive the vehicle moved forward as usual but after 100 ft. I heard a loud crunch and lost forward motion. I can use 1st and 2nd range also...


The direct drive sungear is most likely the problem inside the transmision. The brass bearings do wear and the gearing get sloppy causing this noise. A complete tear down of the trans will have to be performed or a rebuilt trans is needed. If this has many miles on it replace the trans

Jun 30, 2010 | Cars & Trucks

2 Answers

I have 1998 Chevy Suburban 4wheel drive half ton. Was driving out of parking lot when a loud bang frome the rearend. The car still kept going without further noise. When I got home I found out it would go...


If it slips in reverse and 3rd gear the direct clutches are damaged or the 3rd gear /direct piston is cracked. If 3rd is solid but you lost reverse instantly then the reverse servo or band broke. If this is the case you can tell by putting the truck in manual low one,take off and get up to about 25 mph,normally when you let off the gas your truck would compression brake,with the low reverse band inop truck will coast like its in neutral. If this is the case before pulling the trans,drop the pan and pull the low servo cover (round with 6 bolts w/10 mm heads) If it is broken you can easily fix it by buying a new one for under 30$ from the dealer.

It is very common for the reverse band to break. Probably time for a rebuild.

Sep 13, 2009 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

How do I fix a 1995 buick park avenues front seat motors?


I had that problem with the motor for seat back tilt.
I had to remove the seat and take the cables out of the motor and connect the drive cables to 2 drills one in forward and one in reverse. I lubricated the threaded shafts and the drive unit with WD40 then ran the drills back and forward till it started moving again. then I lubed again with more wd40 and ran seat back all the way forward and back many times. reassembled and tested the motor by connecting 12 volt cordless drill batery to the motor to verify it is now working.
The problem that I am now having is no power to the drivers side and do have power on pasenger side, think they are the same fuse. Need schmatic/wire diagram to continue my trouble shooting . This should help with yours. test each motor with the cordless drill battery. reverse polarity to reverse direction.

May 30, 2009 | 1995 Buick Park Avenue

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...