Question about Cars & Trucks

1 Answer

Is there a fuse for the waterpump - Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 5,252 Answers

Never heard of an electric water pump in a car. All that I know of are driven by a belt on the front of the engine, sometimes the timing belt, sometimes the serpentine belt.

Posted on Dec 06, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a fuse tjat runs the waterpump


No, The water pump either runs with one of the belts or on some vehicles runs directly off one of the timing gears

Dec 06, 2014 | Cars & Trucks

1 Answer

Rodeo waterpump blew now wont start


Hi, The first thing I would check is the BATTERY. Check the connections and wire conditions. The waterpump has no connection to the battery. The motor drives the pump. Hope that helps.

Aug 13, 2014 | Cars & Trucks

1 Answer

What would cause 98cavalier to overheat while sitting still


multiple possibilities. thermostat bad. loose fins on waterpump. cooler fan not engaging for some reason - fuse, etc. low amount of coolant. start with simple things first - coolant - check to see if fan engages - thermostat.

Jun 03, 2014 | 1998 Chevrolet Cavalier

1 Answer

Does the heater core have its own fuse? in a 95 crown vic..if so whats the number


the heater/ac has a fuse. the heater coil is conected to the block or waterpump with a lead and return there is no fuse in the heater core its self. i belive this is a 30amp fuse under the dash #9

Nov 24, 2013 | 1995 Ford Bronco

1 Answer

Waterpump


pull out your coolant res.
pull off your belt.
you will see the old waterpump.
remove all four bolts.
clean off gasket off waterpump mount on motor.
place gasket.
install.

Jun 30, 2012 | 1999 Pontiac Sunfire

1 Answer

Overheating


my car is overheating .i have replaced the thermostat,but it is still overheating ,idont know where the waterpump is located,and i i also need to know what ,fuses and relays are involved with this problem

Mar 07, 2011 | 1997 Chevrolet Lumina

1 Answer

Procedure on changing waterpump


  1. first drain the cooling system.
  2. loosen bolts on the waterpump pulley and remove the inner fender cover on the pass/side.
  3. remove the surpentine fan belt, note; make a diagram of the belt routing so belt will go back on the right way.
  4. remove the bolts you loosened on the pump pulley, use a pry bar to pry engine back to have enough room to remove the waterpump pulley.
  5. remove the bolts holding waterpump, you will want a pan under the van to catch coolant when waterpump is removed,
  6. remove the pump and clean old gasket off the block and install new pump,
  7. reverse to install new pump and fill system with coolant allow engine to run until thremostat opens,hope this is helpful. heres a few diagrams of the waterpump and the cover and the belt routing, good luck and hope this is helpful.
  8. e0c2b8f.png3e5449e.giff12ccdc.gif

Oct 27, 2010 | 2005 Dodge Caravan

2 Answers

Do you have to remove power steering belt pulley to change the water pump?


no, just remove the belt, then the cover over the waterpump then the waterpump pulley,NOTE; loosen waterpump pulley bolts before removing the belt,just loosen dont remove!,next is to remove bolts holding waterpump and pump comes out,9e51b2d.gif

Apr 10, 2010 | 2004 Chevrolet Impala

1 Answer

My 2001 dodge sport 3.3 lt is over heating and i did replace the therm


check the antifreeze the waterpump may be going check all fuses

Sep 21, 2009 | Dodge Caravan Cars & Trucks

1 Answer

Engine will not start on 2000 chrysler cirrus


anti freeze has rust because these have crappy heater cores mine has been pressure cleaned 3 times this year oil on plug is vave cover leak mine is leaking as well when you replace waterpump on this car you should replace timing belt as well as waterpump runs on timing belt as far as it not starting check to see if you have spark if not check crank sensor

Mar 27, 2009 | 2000 Chrysler Cirrus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...