Question about 1993 Dodge Power Ram 50

1 Answer

How to remove front rotor

Nothing

Posted by on

1 Answer

You Tube Video

Posted on Dec 05, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front rotor will not tighten down


Nothing. The rotor is held on by being sandwiched between the wheel and the hub. You slide it (the brake rotor) over the studs and mount the caliper over the rotor. Then fasten the caliper to its attach points. When you mount the tire/wheel and tighten the lugnuts this prevents the rotor from coming off. Get yourself to the local library, and checkout the automotive repair manual for your make and model of car. Run through the steps for removing/replacing the brake rotor. Verify you did all the steps correctly!! Good luck.

Nov 08, 2013 | 2005 Pontiac Grand Prix

1 Answer

ROTOR REMOVAL


It may have a center locking nut. Remove the center nut and see if this helps. careful though this is also where the wheel bearings are located. If it does not, place a pry bar behind the rotor and pull while one person hits the other rotor from the back with a hammer (3 - 4 lb hammer) then hit the front.

Mar 31, 2012 | Mercury Mystique Cars & Trucks

1 Answer

How to remove crossfire front brake rotors


front rotor removal you need to remove the brake caliper including the brake caliper bracket so nothing is in the way, there should be a 7mm set screw in the rotor remove that, then get some pb blaster and spray the center part of the hub and the back part of the hub very liberally then you have to use a hammer and beat it off, a way to make it easier is to rotate the rotor as you beat it. It will come off.

Sep 27, 2011 | 2005 Chrysler Crossfire

2 Answers

How to remove the rotor on a navigator?


front or rear brake rotor? b sure to shut off the air ride system! the switch is located in the rear kick panel! lift and support front remove tires !the caliper has two mounting bolts remove those and hang caliper to the side using a metal coat hanger! now look at the bracket that was connected to the caliper remove those two bolts !the rotor should come off

Mar 16, 2010 | 2001 Lincoln Navigator

1 Answer

Help with doing pads and rotors in back.


Interesting!... What/Where did you hear about 'factory bolts shearing" I've done some research and have found NOTHING with regard to this. The rear brake service procedure is no different than the front (except, you must release the emergency brake in order to remove the rear rotors). I don't understand your concern. I sincerely hope you are resurfacing (remachining) rotors and replacing pads. It's important rotors be remachined (resurfaced) when replacing pads... if not, rotors can overheat and wear out faster than their normal lifetime.

Jun 05, 2009 | 2003 Hyundai Santa Fe

1 Answer

I need to know the procedure for r and r on a front rotor if this is something that can be done at home with limited tools?


1999 Taurus/Sable Section 06-03: Brakes, Front Disc 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Disc Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Be careful to avoid damage or interference with caliper bleeder screw fitting and front disc brake rotor shield (2K004).
  1. ani_caut.gif CAUTION: Handle front disc brake rotor (1125) and disc brake caliper (2B120) assembly in such a way as to prevent deformation of front disc brake rotor , and nicking, scratching or contamination of brake linings/rotor surfaces.
    NOTE: To prevent damage, do not allow disc brake caliper to hang by the front brake hose (2078) .


    Remove caliper anchor plate bolts and discard. Position disc brake caliper out of the way. Prevent separation of caliper housing from anchor bracket because contamination of guide pin journals can occur.
  1. NOTE: If excessive force must be used during front disc brake rotor removal, the front disc brake rotor should be checked for runout prior to installation.


    If additional force is required to remove front disc brake rotor , apply Rust Penetrant and Inhibitor F2AZ-19A501-A or equivalent meeting Ford specification ESR-M99C56-A on front and rear rotor/hub mating surfaces. First, strike front disc brake rotor between lug bolts (1107) with a plastic hammer. If this does not work, attach 2-3 Jaw Puller 205-D027 (D80L-1013-A) or equivalent and remove front disc brake rotor . Remove front disc brake rotor from wheel hub (1104) assembly by pulling it off the lug bolts.
Installation
  1. If original front disc brake rotor is being installed, make sure rotor braking and mounting surfaces are clean.
  1. ani_caut.gif CAUTION: Failure to clean rust and foreign material from rotor and hub mounting faces when installing new or old front disc brake rotors will result in high rotor runout, which will speed up the development of brake roughness shudder vibration.
    Apply a small amount of Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A or equivalent meeting Ford specification ESE-M1C171-A to pilot diameter of front disc brake rotor.
  1. Install front disc brake rotor on wheel hub assembly.
  1. Install disc brake caliper and new caliper anchor bracket bolts on front disc brake rotor . Tighten caliper anchor bracket bolts to 88-118 Nm (65-87 lb-ft).
  1. ani_caut.gif CAUTION: Failure to tighten lug nuts (1012) in a star pattern may result in high rotor runout, which will speed up the development of brake roughness, shudder and vibration.
    Install wheel and tire assembly on vehicle. Tighten lug nuts to 115-142 Nm (85-104 lb-ft) using Rotunda Accutorq® Lug Nut Socket 164-R0303 or equivalent on a 1/2 inch air impact wrench, or use a torque wrench.
  1. Lower vehicle.
  1. Pump brake pedal prior to moving vehicle to position brake linings.
  1. Road test vehicle.









May 25, 2009 | 1999 Mercury Sable

1 Answer

Removing the front rotors on a 2005 dodge


They should just come off. but may need some hammer to assist. they tend to rust up like most other rotors. nothing special needed.

Feb 14, 2009 | 2005 Dodge Ram 2500 Truck

2 Answers

Humming


It may be the bearing. located underneath the wheel rotor on the wheel axle. Lift up the car and remove the wheel, brake pads and rotor. remove the rotor and turn the nut that holds to axle in place by removing a small pin. (if there is one) and turning counter clockwise. you will see the bearing under the rotor. Check for missing bearings , dirty oil debris, etc. If it has any of this , replace with new bearing. The exact way you removed it. Do not overtighten the nut. This will cause the bearing to overheat. just tighten enough for the bearing to fit snug with no movement.Make sure you grease up the new bearing good.

Dec 16, 2008 | 2003 Nissan Altima

1 Answer

1998 honda civic front rotor replacement


Varvah, front rotor: Jack up the car, put on safety stands, remove wheel, remove caliper mounting bolts (2), hang caliper in place w/ bungy cord, rope, etc. so you don't stress the brake line, remove caliper mounting bracket bolts, remove bracket from rotor, remove retaining screws on the front of the rotor, remove rotor. If it's stuck, get 2 - 8x 1.25 mm screws (longer version of what u removed), tighten them in the rotor, they will push it off easily. Reverse to install, tighten bracket to 80 ft lbs, caliper to 20 ft lbs. Let me know if u need more info. Countrycurt0

Oct 09, 2008 | 1998 Honda Civic

Not finding what you are looking for?
1993 Dodge Power Ram 50 Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...